Home › Engine / Hybrid System › N04C-UH (LUBRICATION) › LUBRICATION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _073179 N04C-UH LUBRICATION _0356102 LUBRICATION SYSTEM G

N04C-UH LUBRICATION  LUBRICATION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ENGINE OIL LEVEL

a.

Warm up the engine, then stop the engine and wait for 5 minutes.


b.

Check that the engine oil level is between the low level and full level marks on the level dip stick.

NOTICE:

Do not fill with engine oil to above the full level mark.


HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

·

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

·

If low quality oil or oil of an inappropriate viscosity is used.

·

When driving at high engine speed or with a heavy load, (when towing or), when driving while accelerating or decelerating frequently.

·

When idling for a long time, or when driving frequently through heavy traffic.


When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



Hide 2.INSPECT FOR ENGINE OIL PRESSURE

a.

Remove the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-UH (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.
A448323C01
0.281,0.5 0.615,0.5 true 1.083,2.75 1.583,2.75 false 1.01,3.406 1.51,3.406 false 1.031,3.833 1.448,3.833 false 1.01,4.24 1.51,4.24 false 2.417,3.719 2.583,3.469 2.583,3.469 2.75,3.469 false 2.271,0.479 2.688,0.479 true 0.104,0.417 0.354,0.667 0.25,0.25 10 true *1 0.917,2.667 1.25,2.927 0.333,0.26 10 false *a 0.833,3.333 1.167,3.573 0.333,0.24 10 false *b 0.854,3.75 1.083,4 0.229,0.25 10 false *c 2.771,3.385 3.104,3.594 0.333,0.208 10 false *d 2.104,0.385 2.323,0.615 0.219,0.229 10 true *e 0.833,4.167 1.167,4.406 0.333,0.24 10 false *b
*1 Engine Oil Pressure Switch Assembly
*a Union Bolt
*b Gasket
*c Union
*d Adapter
*e Oil Pressure Gauge


Install the union and 2 new gaskets to the oil cooler cover sub-assembly with the union bolt.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Install an oil pressure gauge with an adapter.


d.

Warm up the engine.


e.

Measure the engine oil pressure.

Oil pressure:
Engine condition Specification
Idling 190 kPa (1.9 kgf/cm2, 27.6 psi)


HINT:

If the pressure is not as specified, check the oil pump.



f.

Remove the oil pressure gauge and adapter.


g.

Remove the union bolt, union and 2 gaskets.


h.

Install the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-UH (LUBRICATION)>OIL PRESSURE SWITCH>INSTALLATION