Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355905 ENGINE UNIT A

N04C-VQ ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING

a.
A151662C01
0.396,0.938 0.563,0.323 false 1.542,0.802 1.688,0.271 false 2.458,0.656 2.583,0.198 false 0.552,1.354 0.656,1.771 false 2.604,1.083 2.865,1.281 2.865,1.281 2.563,0.729 false 1.635,1.229 1.729,1.583 false 2.625,0.094 2.927,0.281 0.302,0.188 10 false *c 0.698,1.719 1.073,1.875 0.375,0.156 10 false *a 1.771,1.521 2.146,1.677 0.375,0.156 10 false *b 1.667,0.104 1.854,0.292 0.188,0.188 10 false *d 0.552,0.167 0.74,0.354 0.188,0.188 10 false *d 2.823,1.313 3.01,1.5 0.188,0.188 10 false *e
*a No. 1 Camshaft Bearing
*b No. 2 Camshaft Bearing
*c No. 3 Camshaft Bearing
*d Notch
*e Oil Hole


Be sure to face the notches of the No. 1 camshaft bearing and No. 2 camshaft bearing and oil holes of the No. 3 camshaft bearing in the correct direction.


b.
A151661C01
2.844,1.313 2.844,1.573 false 0.448,0.542 0.74,0.771 0.292,0.229 10 false *a 1.438,0.552 1.667,0.75 0.229,0.198 10 false *b 2.427,0.552 2.625,0.729 0.198,0.177 10 false *c 2.677,1.583 2.979,1.729 0.302,0.146 10 false SST
*a No. 1 Journal
*b No. 2 Journal
*c No. 3 Journal
V100135

Front


Using SST, install new camshaft bearings in the direction indicated by the arrows in the illustration.

SST
09215-00101  (09215-00130, 09215-00141, 09215-00150, 09215-00161)
09215-00013  (09215-00021, 09215-00461)

Standard Journal Bearing Diameter:
Item Inside Diameter Outside Diameter
No. 1 journal 57.0 mm (2.244 in.) 60.0 mm (2.362 in.)
No. 2 journal 56.8 mm (2.236 in.) 59.8 mm (2.354 in.)
No. 3 journal 56.6 mm (2.228 in.) 59.6 mm (2.346 in.)


NOTICE:

Install the No. 2 journal, No. 1 journal and No. 3 journal in order.



Hide 13201A 2.INSTALL CONNECTING ROD SMALL END BUSH

a.
A153825

Uniformly chamfer one edge of the bush hole at the small end of the connecting rod sub-assembly.

HINT:
·

Incorrect chamfering can cause the connecting rod small end bush to become out-of-round, which may result in jamming during insertion.

·

Remove dust from the inner surface of the connecting rod hole.




b.
A457681C02
1.167,0.219 1.292,0.219 1.292,0.219 1.854,0.573 true 1.031,1.104 1.24,1.104 1.24,1.104 1.771,1.417 true 1.104,1.573 1.354,1.573 1.354,1.573 1.792,1.74 true 2,1.698 2.51,1.698 true 2,0.938 2.51,0.938 true 1.396,2.01 1.906,2.01 true 0.969,0.115 1.198,0.313 0.229,0.198 10 false *a 0.906,1.49 1.094,1.656 0.188,0.167 10 false *c 1.177,1.927 1.417,2.104 0.24,0.177 10 false *d 0.833,1.01 1.031,1.198 0.198,0.188 10 false *b 2.552,0.854 2.771,1.031 0.219,0.177 10 false *e 2.552,1.615 2.75,1.844 0.198,0.229 10 false *e
*a SST (Spindle)
*b Bush
*c SST (Guide)
*d SST (Bolt)
*e Groove


Install the new connecting rod small end bush to SST and tighten the bolt.

SST
09222-E7020  09222-E7030  S9191-08252  

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Align the groove of SST (spindle) with the groove of SST (press sub-assembly) to install SST.


i.

Apply fresh engine oil to the connecting rod small end bush and guide.



c.
A153799C05
1.01,0.542 1.135,0.542 1.135,0.542 1.427,1.292 true 0.417,1.458 0.542,0.906 0.542,0.906 0.677,0.906 true 2.604,1.375 2.813,0.656 2.813,0.656 2.938,0.656 true 0.802,0.458 1.083,0.688 0.281,0.229 10 false *a 0.75,0.833 1,1.031 0.25,0.198 10 false *b 3.021,0.583 3.26,0.771 0.24,0.188 10 false *c
*a SST (Guide)
*b SST (Wing Nut)
*c SST (Press Sub-assembly)


Prepare SST.

SST
09222-E7010  S0948-11130  S9233-10360  

i.

Install the press sub-assembly to the guide by inserting the pin of the press sub-assembly into the guide, and then secure them together by installing the wing nut.

HINT:

Orient the guide so that the letter W, which is stamped on the guide, is above the pin.



ii.
A457679C03
2.573,0.688 2.885,0.688 true 2.396,0.594 2.604,0.781 0.208,0.188 10 false *a
*a Groove


With the connecting rod bearing removed, install the connecting rod bearing cap and place the connecting rod on SST with its chamfered side facing upward.

HINT:

Place SST so that the groove of SST (press sub-assembly) is at the center of the connecting rod.




d.
A457682C01
1.729,0.802 2.313,1.083 2.313,1.083 1.729,1.292 true 1.729,1.771 2.323,1.771 true 2.354,1.021 2.594,1.198 0.24,0.177 10 false *a 2.365,1.698 2.573,1.885 0.208,0.188 10 false *a
*a Groove


Align the groove of SST (guide) with the groove of SST (press sub-assembly) to install the connecting rod small end bush using a press.

HINT:

Align the groove of the SST (guide) with the groove of the SST (guide) with the groove of the SST (press sub-assembly) and install.



e.
A153798

Inspect the connecting rod small end bush position after installation.

i.

Make sure that the oil hole of the connecting rod small end bush and the oil path of the connecting rod are properly aligned, allowing a 6 mm (0.236 in.) diameter rod to pass through.

HINT:

Misalignment can lead to insufficient lubrication, which may result in piston seizure.



ii.

With a new piston pin inserted in the piston, make sure that the pin can be rotated by hand and is not loose.



Hide 13101A 3.INSTALL PISTON PIN HOLE SNAP RING

a.
A151668

Using snap ring pliers, install a new snap ring into one side of the piston hole.


Hide 4.INSTALL PISTON

HINT:

Before assembling the piston with the connecting rod, check whether the piston is specified for this engine. The check should be performed using the engine compatible identification code on the top of the piston.


Engine compatible identification:

35


a.

Assemble the piston and connecting rod.

i.

Gradually heat the piston to approximately 50°C (122°F).

CAUTION:

Do not touch the piston while it is hot.



ii.

Coat the piston pin with engine oil.


iii.
A151670C01
2.646,1.729 2.073,1.802 false 0.719,0.5 0.521,0.24 false 0.313,0.104 0.542,0.313 0.229,0.208 10 false *a 1.865,1.719 2.094,1.927 0.229,0.208 10 false *b
*a Notch
*b Alignment Mark


Install the piston onto the connecting rod with the notch on the piston facing in the same direction as the alignment mark on the rod. Then, secure them with the piston pin.


iv.
A151671

Check that the piston and piston pin fit securely.

HINT:

Try to move the piston back and forth.



v.
A151672

Using snap ring pliers, install a new snap ring into the other side of the piston pin hole.



Hide 13011 5.INSTALL PISTON RING SET

a.
A151673

Face the identification marks on the piston ring up, then using a piston ring expander, install them in the following order of the oil ring, 2nd ring and 1st ring.

HINT:
·

Never change the combination of the coil and oil ring.

·

Connect the joint of the coil expander for the oil ring and install it inside the oil ring. Align the expander joint 180° opposite to the gap of the ring.




Hide 15708 6.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Install the No. 1 oil nozzle sub-assembly with the bolt.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)

NOTICE:
·

If the No. 1 oil nozzle sub-assembly has been dropped or any impact has occurred to the nozzle, replace the No. 1 oil nozzle sub-assembly.

·

Replace a deformed No. 1 oil nozzle assembly.




Hide 11271A 7.INSTALL REAR CYLINDER BLOCK COVER

a.

Install a new O-ring and the rear cylinder block cover with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 15605 8.INSTALL OIL CHECK VALVE SUB-ASSEMBLY

a.

Install a new gasket and the oil check valve with the bolt.

Torque:
41.5 N*m (423 kgf*cm, 31 ft.*lbf)


Hide 11702 9.INSTALL CRANKSHAFT BEARING SET

a.
A151548C01
1.292,1.156 0.563,1.74 false 0.365,1.698 0.563,1.875 0.198,0.177 10 false *a
*a Oil Hole


Align the oil groove of the crankshaft bearing with the oil hole of the cylinder block sub-assembly, and push in the 5 upper crankshaft bearings.

NOTICE:

Keep the back side of the crankshaft bearing and the crankshaft bearing surface free of foreign matter.



b.
A450225

Align the crankshaft bearing with the crankshaft bearing cap, and push in the 5 lower crankshaft bearings.

NOTICE:

Keep the back side of the crankshaft bearing and the crankshaft bearing surface free of foreign matter.



c.

Install the crankshaft.


d.
A151674C01
1.771,1.021 1.938,1.792 1.938,1.792 1.833,1 false 1.875,1.823 2.063,2.01 0.188,0.188 10 false *a
*a Groove


Insert the crankshaft thrust washer into the clearance between the cylinder block sub-assembly and crankshaft with the oil groove facing outward.

NOTICE:

Be sure to install the removed crankshaft thrust washer to its original position.



e.
A151544C01
1.719,1.844 1.365,2.802 false 1.688,1.75 1.198,0.698 false 1.146,2.76 1.333,2.948 0.188,0.188 10 false *b 1.094,0.531 1.281,0.719 0.188,0.188 10 false *a
*a Front Mark
*b Journal No.


Install the crankshaft bearing caps onto the cylinder block sub-assembly.

HINT:

When installing the crankshaft bearing caps, return them to their original locations according to the number stamped on the crankshaft bearing caps.



f.

Apply a light coat of engine oil to the threads and under the crankshaft bearing cap bolt.


g.
A151545E01
0.589,0.124 0.762,0.273 0.172,0.149 10 10 0.685,0.797 0.685,0.33 false 1.174,0.124 1.27,0.273 0.096,0.149 10 6 1.222,0.797 1.222,0.33 false 1.723,0.124 1.819,0.273 0.096,0.149 10 2 1.77,0.797 1.77,0.33 false 2.264,0.124 2.36,0.273 0.096,0.149 10 4 2.312,0.797 2.312,0.33 false 2.801,0.124 2.897,0.273 0.096,0.149 10 8 0.638,1.942 0.737,2.091 0.098,0.149 10 9 1.173,1.942 1.269,2.091 0.096,0.149 10 5 1.722,1.942 1.818,2.091 0.096,0.149 10 1 2.263,1.942 2.359,2.091 0.096,0.149 10 3 2.8,1.942 2.896,2.091 0.096,0.149 10 7 2.849,0.797 2.849,0.33 false 0.685,1.442 0.685,1.909 false 1.222,1.442 1.222,1.909 false 1.77,1.442 1.77,1.909 false 2.312,1.442 2.312,1.909 false 2.849,1.442 2.849,1.909 false

Step 1:

i.

Temporarily install the bolts and tighten them in several steps in the sequence shown in the illustration.



h.

Tighten the bolts to the specified torque.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


i.

Step 2:

i.

Mark the front of the bearing cap bolts with paint.


ii.

Tighten the bolts 60°.



j.

Step 3:

i.

Tighten the bolts 60°.


ii.

Check that each paint mark is now at a 120° angle to the front.



Hide 11462 10.INSTALL CYLINDER LINER

HINT:
·

When assembling the cylinder liner into the cylinder block sub-assembly, the clearance can be set to 3 levels.

·
A448342C01
1.438,1.854 1.042,1.385 false 1.438,1.844 2.292,1.385 false 1.396,4.094 1.719,3.5 false 1.385,1.875 1.698,2.188 0.313,0.313 10 false *a 1.26,4.094 1.573,4.406 0.313,0.313 10 false *a
*a Position of Mark A, B or C


The upper surface and side surface of the cylinder block sub-assembly are stamped A, B or C. When using a new cylinder liner, insert a matching cylinder liner with the same symbol.



a.

Apply engine oil to the cylinder block sub-assembly inside bore.


b.
A151676C01
1.292,1.188 1.063,0.927 1.063,0.927 0.896,0.927 false 0.74,0.833 0.927,1.031 0.188,0.198 10 false *a
*a Mark


Align the marks of the cylinder liner and cylinder block sub-assembly.

HINT:

When reusing the cylinder liner, install it according to the marks made during the removal. When reusing the cylinder liner, misalignment with the cylinder block sub-assembly may concentrate stress on the thin part of the cylinder liner and it may break.



c.

Install the cylinder liner.

NOTICE:

Make sure to install the cylinder liner to its original location.



Hide 11.INSPECT PROTRUSION OF CYLINDER LINER

a.
A151677E01
0.212,0.142 0.51,0.29 0.297,0.148 10 SST 0.795,0.45 0.579,0.233 false

Mount SST onto the cylinder block sub-assembly.

SST
S0942-01460  


b.

Tighten the center bolt to the specified torque below to set SST in the proper installation position.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


c.
A448343C02
0.938,0.698 1.302,0.938 0.365,0.24 10 false *a
*a Protrusion


Using a dial indicator, measure the protrusion of the cylinder liner.

Standard protrusion:

0.01 to 0.08 mm (0.000394 to 0.00315 in.)


Maximum protrusion:

0.08 mm (0.00315 in.)


If the protrusion is more than the maximum, replace the cylinder liner.


Hide 13202 12.INSTALL CONNECTING ROD BEARING SET

A450223

NOTICE:
·

When reusing the connecting rod bearing, reassemble the removed connecting rod bearing as it was originally installed.

·

Install the connecting rod bearing with the oil hole onto the connecting rod side and install the connecting rode bearing without the oil hole onto the connecting rod bearing cap side.

·

Match the connecting rod bearing protrusion with the notch of the connecting rod or connecting rod bearing cap.

·

Keep the back side of the connecting rod bearing and connecting rod bearing surface of the connecting rod bearing cap free of foreign matter.



Hide 13301A 13.INSTALL PISTON WITH CONNECTING ROD

HINT:
A151680C02
1.594,1.573 1.802,1.74 0.208,0.167 10 false 35 2.583,1.063 2.771,1.24 0.188,0.177 10 false *3 1.208,1.917 1.396,2.094 0.188,0.177 10 false *2 1.125,0.208 1.313,0.385 0.188,0.177 10 false *1 1.792,0.208 1.979,0.385 0.188,0.177 10 false *a
*1 2nd Ring
*2 Oil Ring
*3 Top Ring
*a Mark


Position the gaps of the piston rings at an even distance. Be careful not to position the gaps at the same position as the piston mark.


a.
A151681

Using a piston ring compressor and a hammer handle, insert the piston with connecting rod assembly into the cylinder block sub-assembly.

HINT:
·

Before the installation, apply engine oil to the piston pin, piston ring, cylinder liner and connecting rod bearing.

·

Recheck the gap of each piston ring.

·

Do not damage the inside of the liner.



i.
A151682E06
1.594,1.667 1.427,1.875 1.427,1.875 1.927,1.656 false 2.583,1.583 2.417,1.583 2.417,1.583 1.781,1.271 false 2.615,1.479 2.833,1.646 0.219,0.167 10 false *a 1.26,1.833 1.458,2.01 0.198,0.177 10 false *b

Make sure that the mark on the piston is on the tappet chamber side.



b.

Install the bearing cap onto the connecting rod with the "0" mark facing in the correct direction.


c.

Step 1:

i.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


ii.

Install and uniformly tighten the connecting rod cap bolts to the specified torque in several steps.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



d.

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the connecting rod cap bolts 60°.



e.

Step 3:

i.

Tighten the connecting rod cap bolts an additional 60°.


ii.

Check that the paint marks are now at a 120° angle to the front.



Hide 11381A 14.INSTALL REAR ENGINE OIL SEAL

a.
A178279C01
1.604,0.958 2.615,0.563 false 2.688,0.427 3.094,0.615 0.406,0.188 10 false SST 2.802,1.948 3.198,2.135 0.396,0.188 10 false *a
*a 4 mm (0.157 in.)


Using SST and a hammer, tap in a new rear engine oil seal until it is 4 mm (0.157 in.) below the upper edge of the flywheel housing.

SST
09223-78010  

NOTICE:
·

Be careful not to tap the rear engine oil seal at an angle.

·

Keep the gap between the rear oil seal retainer edge and the oil seal free of foreign matter.




b.

Apply MP grease to the oil seal lip.


Hide 11351 15.INSTALL FLYWHEEL HOUSING

a.

Remove any old seal packing material from the contact surface.


b.
A151493C01
0.977,1.874 1.547,2.921 1.547,2.921 2.064,1.872 false 1.449,2.94 1.626,3.128 0.177,0.188 10 *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

1.5 to 2.5 mm (0.0591 to 0.984 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the flywheel housing within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installation.




c.

Install the flywheel housing with the 14 bolts.

Torque:
for M14 bolt : 132 N*m (1346 kgf*cm, 97 ft.*lbf)
for M8 bolt : 28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 13453 16.INSTALL FLYWHEEL RING GEAR

a.

Using a torch, heat the flywheel ring gear evenly to approximately 200°C (392°F).

NOTICE:

Be careful not to overheat the flywheel ring gear.



b.
A451503C01
0.854,0.594 0.99,0.594 0.99,0.594 1.417,0.458 false 0.875,0.229 1.052,0.229 1.052,0.229 1.5,0.438 false 1.719,0.969 2.167,0.969 false 0.708,0.167 1.021,0.323 0.313,0.156 10 false *1 2.208,0.875 2.521,1.031 0.313,0.156 10 false *2 0.667,0.5 0.979,0.656 0.313,0.156 10 false *a 1.479,0.083 1.792,0.24 0.313,0.156 10 false *b
*1 Flywheel Ring Gear
*2 Flywheel Assembly
*a Chamfer
*b 0.25 mm (0.00984 in.) or less


Using a brass bar, strike the flywheel ring gear onto the flywheel assembly with its chamfered flywheel ring gear teeth facing the block.

Standard Clearance:

0.25 mm (0.00984 in.) or less


NOTICE:

After installing, allow the flywheel ring gear to cool before handling.



Hide 13450A 17.INSTALL FLYWHEEL ASSEMBLY

a.

Insert the flywheel assembly slowly until it contacts the collar knock in order to prevent impact with the guide bar. Adjust the position, then insert it completely.

NOTICE:

The flywheel assembly is heavy. When installing the flywheel assembly, be careful not to drop it.



b.

Apply a light coat of engine oil to the threads of the flywheel bolts and flywheel bolt seats.


c.

Temporarily install the flywheel assembly with the flywheel bolts.


d.
A259187E01
1.635,0.313 1.792,0.51 0.156,0.198 10 false 1 2.188,0.542 2.344,0.74 0.156,0.198 10 false 8 2.438,1.094 2.594,1.292 0.156,0.198 10 false 4 2.208,1.677 2.365,1.875 0.156,0.198 10 false 6 1.635,1.917 1.792,2.115 0.156,0.198 10 false 2 1.083,1.688 1.24,1.885 0.156,0.198 10 false 7 0.865,1.104 1.021,1.302 0.156,0.198 10 false 3 1.094,0.552 1.25,0.75 0.156,0.198 10 false 5

Step 1:

i.

Tighten the flywheel bolts in several steps in the order shown in the illustration.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to prevent the flywheel ring gear from turning together with the crankshaft.




e.

Step 2:

i.

Mark the top of each flywheel bolt head with paint.


ii.

Tighten the bolts 45° in the order shown in the illustration.


iii.

Check that the paint marks are now at a 45° angle to the top.



f.
A151495

Using a dial indicator, measure the runout of the flywheel assembly.

Maximum runout:

0.15 mm (0.00591 in.)


If the runout is more than the maximum, resurface the sliding surface.


g.
A151486

Temporarily install 4 bolts in the positions of the cylinder block sub-assembly shown in the illustration to prevent the wires from sliding toward the center of the cylinder block sub-assembly.


h.

Attach 2 wires to the cylinder block sub-assembly.

HINT:

The wires must be attached outside the installed bolts.



i.

Using a chain block and an engine sling device, install the cylinder block sub-assembly onto the engine stand.


j.

Remove the 4 bolts from the cylinder block sub-assembly.


Hide 11311H 18.INSTALL FRONT END PLATE

a.

Install the front end plate with a new gasket and 4 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.
A260709C03
0.635,1.094 1.052,1.094 false 1.802,1.552 2.219,1.552 false 0.99,1.729 1.156,1.729 1.156,1.729 1.458,1.406 false 0.969,0.24 1.135,0.24 1.135,0.24 1.354,0.51 false 1.5,0.531 1.667,0.313 1.667,0.313 1.833,0.313 false 0.802,0.156 1.115,0.354 0.313,0.198 10 false *2 1.875,0.219 2.188,0.417 0.313,0.198 10 false *3 2.042,0.604 2.354,0.802 0.313,0.198 10 false *4 2.24,1.469 2.552,1.667 0.313,0.198 10 false *a 0.479,1 0.792,1.198 0.313,0.198 10 false *1 0.844,1.615 1.156,1.813 0.313,0.198 10 false *b
*1 Timing Gear Cover
*2 Front End Plate
*3 Gasket
*4 Cylinder Block Sub-assembly
*a Cutter
*b Cut


Using a cutter, cut the gasket so that it is flush with the lower surface of the cylinder block sub-assembly.


Hide 15100 19.INSTALL OIL PUMP ASSEMBLY

a.
A151496C01
1.177,0.844 2.25,0.844 false 2.26,0.75 2.49,0.938 0.229,0.188 10 false *a
*a Engine Oil


Apply engine oil to the oil pump case of the cylinder block sub-assembly shown in the illustration.

NOTICE:

If engine oil is not applied, an oil suction malfunction will occur when starting the engine. The malfunction causes seizure or abnormal wear to the engine.



b.

Install a new gasket and oil pump assembly with the 7 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


c.

Check that the oil pump rotates smoothly by hand after the installation.


Hide 13521 20.INSTALL CRANKSHAFT GEAR

a.
A151497C01
2.938,1.24 2.708,1.99 2.708,1.99 2.74,1.26 false 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 2.615,2 2.823,2.188 0.208,0.188 10 false *b
*a No. 1, No. 4 Cylinder
*b Alignment Mark


Turn the crankshaft clockwise, and align the alignment mark on the flywheel assembly with the alignment mark between the 2 numbers on the edge of the flywheel housing to set the No. 1 cylinder to TDC/compression.


b.

Align the set key on the crankshaft with the key groove of the crankshaft gear.


c.

Using a hammer, tap on the crankshaft gear.


Hide 13572B 21.INSTALL NO. 1 IDLE GEAR THRUST PLATE

a.

Install the No. 1 idle gear sub-assembly and No. 1 idle gear thrust plate onto the No. 1 idle gear shaft.


b.
A403295C01
1.458,1.01 2.406,0.865 2.406,0.865 1.417,1.083 false 2,2.302 2.458,1.646 2.458,1.646 2.094,2.313 false 2.458,1.646 2.625,1.646 false 1.344,3.042 1.51,3.042 1.51,3.042 2.01,2.427 false 0.719,1.667 0.885,1.667 0.885,1.667 1.313,1 false 2.417,0.75 2.646,0.948 0.229,0.198 10 false *a 2.667,1.583 2.896,1.781 0.229,0.198 10 true *a 1.167,2.948 1.396,3.146 0.229,0.198 10 false *a 0.542,1.583 0.698,1.75 0.156,0.167 10 true *a
*a Alignment Mark


With the No. 1 idle gear shaft oil hole facing down, match the alignment marks for each gear, and insert the shaft into the cylinder block sub-assembly.

NOTICE:
A151498C01
1.948,1.177 2.5,1.5 2.5,1.5 2.583,1.5 false 2.646,1.385 2.833,1.563 0.188,0.177 10 false *a
*a Oil Hole


If the oil hole is not facing down, it causes burning or abnormal wear.



c.

Tighten the bolt.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 13501 22.INSTALL CAMSHAFT SUB-ASSEMBLY

Hide 13581C 23.INSTALL NO. 2 IDLE GEAR SHAFT

a.
A151501C01
1.958,1.458 2.583,1.667 2.583,1.667 2.667,1.667 false 2.698,1.563 2.948,1.781 0.25,0.219 10 false *a
*a Oil Hole


Install the lock plate onto the front end plate with the 3 bolts.


b.

Install a new O-ring onto the No. 2 idle gear shaft.


c.

With the No. 2 idle gear shaft oil hole facing down, install the No. 2 idle gear shaft onto the lock plate with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

If the oil hole is not facing down, it causes burning or abnormal wear.



Hide 13508N 24.INSTALL NO. 2 IDLE GEAR SUB-ASSEMBLY

a.
A151502C01
1.781,1.25 1.823,1.292 0.042,0.042 1.917,1.292 1.958,1.333 0.042,0.042 1.896,1.177 1.938,1.219 0.042,0.042 1.927,1.188 2.188,0.635 2.188,0.635 1.938,1.302 false 1.135,1.76 1.802,1.271 false 0.99,1.781 1.177,1.969 0.188,0.188 10 true *a 2.198,0.531 2.427,0.719 0.229,0.188 10 false *a
*a Alignment Mark


Match the alignment marks of the No. 1 idle gear sub-assembly and No. 2 idle gear sub-assembly and install the No. 2 idle gear sub-assembly.


Hide 13572C 25.INSTALL NO. 2 IDLE GEAR THRUST PLATE

a.

Install the No. 2 idle gear thrust plate with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 11301C 26.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A157089E01
2.446,1.508 2.737,1.653 0.291,0.145 10 SST 1.837,1.065 2.417,1.59 false

Using SST and a hammer, tap the new front crankshaft oil seal into the timing gear cover until the front crankshaft oil seal is flush with the timing gear cover edge.

SST
09223-78010  

NOTICE:
·

Be careful not to tap the front crankshaft oil seal at an angle.

·

Keep the gap between the timing gear cover edge and the front crankshaft oil seal free of foreign matter.




b.

Apply MP grease to the front crankshaft oil seal lip.


Hide 11321C 27.INSTALL TIMING GEAR COVER

a.

Remove any old seal packing material from the contact surface.


b.
A448637C04
2.563,0.583 2.781,0.354 2.781,0.354 2.99,0.354 true 3.042,0.25 3.354,0.406 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the timing gear cover within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installation.




c.

Install the timing gear cover with the 15 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 13470 28.INSTALL CRANKSHAFT PULLEY ASSEMBLY

a.

Install the crankshaft pulley and crankshaft pulley spacer onto the crankshaft.

HINT:

Align the crankshaft pulley set key with the key groove of the crankshaft pulley.



b.

Apply a light coat of engine oil to the threads of the nut.


c.

Step 1:

i.

Using a 46 mm socket wrench, tighten the nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to keep it from turning together with the crankshaft.




d.

Step 2:

i.

Mark the top of each crankshaft pulley bolt head with paint.


ii.

Tighten the nut 90°.


iii.

Check that each paint mark is now at a 90° angle to the top.



Hide 15104 29.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new O-ring onto the cylinder block sub-assembly.


b.

Install the strainer with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 12101 30.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing material from the contact surface.


b.
A146590C06
0.913,1.151 1.112,1.302 0.199,0.151 10 *a 1.744,4.332 1.949,4.483 0.205,0.151 10 *a 1.611,0.702 1.145,1.244 1.145,1.244 1.611,1.892 false 1.611,0.702 1.145,1.244 1.145,1.244 1.611,1.892 false 1.611,0.702 1.145,1.244 1.145,1.244 1.611,1.892 false 1.826,4.119 1.826,4.317 false
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installation.




c.

Install the oil pan sub-assembly with the 26 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 11351H 31.INSTALL FLYWHEEL HOUSING STAY RH

a.

Install the flywheel housing stay RH with the 4 bolts.

Torque:
for M14 bolt : 132 N*m (1346 kgf*cm, 97 ft.*lbf)
for M12 bolt : 97 N*m (989 kgf*cm, 72 ft.*lbf)


Hide 11351G 32.INSTALL FLYWHEEL HOUSING STAY LH

a.

Install the flywheel housing stay LH with the 4 bolts.

Torque:
for M14 bolt : 132 N*m (1346 kgf*cm, 97 ft.*lbf)
for M12 bolt : 97 N*m (989 kgf*cm, 72 ft.*lbf)


Hide 13751 33.INSTALL VALVE LIFTER

NOTICE:

Be sure to install the removed push rod to its original position.


Hide 11101 35.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13819 36.INSTALL VALVE BRIDGE

NOTICE:

Be sure to install the removed valve bridge to its original location.


Hide 13781 37.INSTALL VALVE PUSH ROD

NOTICE:

Be sure to install the removed valve bridge to its original location.


Hide 13901 38.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

a.

Install the No. 1 valve rocker arm sub-assembly, No. 2 valve rocker arm sub-assembly, No. 1 valve rocker support sub-assembly, No. 2 valve rocker support sub-assembly, and No. 3 valve rocker support sub-assembly to the No. 1 valve rocker shaft sub-assembly.

NOTICE:

Make sure that the hole in the No. 1 valve rocker shaft is facing the cylinder head as shown in the illustration.


A462587C01
1.177,0.25 1.365,0.25 1.365,0.25 1.563,0.885 true 2.344,0.354 2.219,0.354 2.219,0.354 2.021,0.844 true 1.104,1.677 1.104,1.375 true 1.854,1.76 2.01,1.76 2.01,1.76 2.365,2.083 true 6.594,0.25 6.719,0.115 6.719,0.115 6.833,0.115 true 2.854,0.323 2.729,0.323 2.729,0.323 2.531,0.813 true 4.135,0.208 4.01,0.208 4.01,0.208 3.854,0.604 true 5.427,0.104 5.302,0.104 5.302,0.104 5.167,0.427 true 0.302,2.396 0.531,2.583 0.229,0.188 10 false *1 1.833,2.385 2.063,2.552 0.229,0.167 10 false *2 5.406,0.938 5.667,1.146 0.26,0.208 10 false *a 5.396,2.281 5.708,2.542 0.313,0.26 10 false *b 0.979,0.167 1.177,0.333 0.198,0.167 10 false *5 1.021,1.76 1.281,1.958 0.26,0.198 10 false *1 1.635,1.698 1.854,1.865 0.219,0.167 10 false *4 6.885,0.063 7.104,0.24 0.219,0.177 10 false *3 2.385,0.281 2.635,0.469 0.25,0.188 10 false *6 2.906,0.26 3.135,0.427 0.229,0.167 10 false *2 4.188,0.146 4.385,0.333 0.198,0.188 10 false *1 5.469,0.042 5.698,0.208 0.229,0.167 10 false *2 3.354,2.396 3.583,2.563 0.229,0.167 10 false *3
*1 No. 1 Valve Rocker Support Sub-assembly *2 No. 2 Valve Rocker Support Sub-assembly
*3 No. 3 Valve Rocker Support Sub-assembly *4 No. 1 Valve Rocker Shaft Sub-assembly
*5 No. 1 Valve Rocker Arm Sub-assembly *6 No. 2 Valve Rocker Arm Sub-assembly
*a Cylinder Head Cover Side *b Cylinder Head Side
V100135

Front - -



b.

Apply engine oil to the valve bridge and valve push rods.


c.

Install the No. 1 valve rocker shaft sub-assembly to the cylinder head sub-assembly.


d.

Apply engine oil to the seats and threads of the installation bolts, and tighten the bolts 1 to 2 threads by hand to determine the position.


e.
A462580E02
1.688,0.365 1.844,0.563 0.156,0.198 10 false 1 1.063,0.365 1.219,0.563 0.156,0.198 10 false 2 2.323,0.365 2.479,0.563 0.156,0.198 10 false 3 0.427,0.375 0.583,0.573 0.156,0.198 10 false 4 2.958,0.365 3.115,0.563 0.156,0.198 10 false 5

Gradually tighten the bolts in several steps in the order shown in the illustration.

Torque:
68.5 N*m (699 kgf*cm, 51 ft.*lbf)

NOTICE:
·

Make sure that the valve push rods do not interfere with the valve adjusting screws.

·

Check that the rocker arm moves smoothly after tightening.

·

Check that the valve bridge is not fallen off or shifted.




Hide 39.ADJUST VALVE CLEARANCE

a.
A151510C01
2.771,0.813 2.823,1.385 2.823,1.385 2.969,0.792 false 2.75,3.042 2.823,3.604 2.823,3.604 2.969,3 false 0.198,0.135 0.417,0.354 0.219,0.219 10 false *a 0.125,2.427 0.354,2.646 0.229,0.219 10 false *b 2.729,1.375 2.917,1.563 0.188,0.188 10 false *c 2.74,3.625 2.917,3.781 0.177,0.156 10 false *c
*a TDC of No. 1 and No. 4 Cylinder
*b TDC of No. 2 and No. 3 Cylinder
*c Alignment Mark


Flywheel housing side:

Turn the crankshaft clockwise to align the alignment mark on the flywheel assembly with the alignment mark between the 2 numbers on the edge of the flywheel housing.


b.
A151511C01
2.906,1.75 2.552,1.219 true 2.906,3.99 2.552,3.458 true 2.146,0.302 2.313,0.302 2.313,0.302 2.604,0.969 false 2.146,2.573 2.313,2.573 2.313,2.573 2.604,3.24 false 0.188,2.333 0.385,2.531 0.198,0.198 10 false *b 0.188,0.104 0.385,0.302 0.198,0.198 10 false *a 2.875,3.99 3.073,4.188 0.198,0.198 10 false *c 2.865,1.75 3.063,1.948 0.198,0.198 10 false *c 1.958,0.208 2.146,0.458 0.188,0.25 10 false *d 1.979,2.469 2.167,2.719 0.188,0.25 10 false *d
*a TDC of No. 1 and No. 4 Cylinder
*b TDC of No. 2 and No. 3 Cylinder
*c Timing Mark
*d Pointer


Crankshaft pulley side:

Turn the crankshaft clockwise to align the alignment mark on the crankshaft pulley with the pointer on the timing gear cover.

HINT:

If not, turn the crankshaft 1 revolution (360°) to align the timing mark with the pointer.



c.
A462577C04
2.563,0.854 2.844,1.521 false 1.229,1.01 2.021,0.24 true 1.219,1.073 1.01,1.781 1.01,1.781 0.781,1.781 true 2.063,0.083 2.26,0.25 0.198,0.167 10 false *a 2.813,1.552 3.063,1.771 0.25,0.219 10 false *b 0.615,1.719 0.792,1.865 0.177,0.146 10 true *1
*1 Lock Nut
*a Adjusting Screw
*b Feeler Gauge


With the No. 1 piston positioned at TDC on the compression stroke, adjust each valve clearance using a feeler gauge.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.3 mm (0.0118 in.)
Exhaust 0.45 mm (0.0177 in.)


HINT:

The feeler gauge should move with a very slight pull.



d.

Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.


e.

Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust between the adjusting screw on the valve rocker arm and the valve bridge.


f.

Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


g.

Recheck the clearance.


h.

Adjust the other valves.

i.

Turn the crankshaft 1 revolution (360°) clockwise.


ii.

Adjust the valve clearance for each cylinder in the firing order.

Firing order:

1 - 3 - 4 - 2

(The cylinder number is counted from the timing gear side)