FAIL-SAFE FUNCTION
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from operating incorrectly.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| Function | Control Master
(Main ECU to determine controls) |
System Related | Fail-safe Operation | Indicator and Buzzer Behavior or User Notification | DTC Detection
(ECU that stored DTC) |
|---|---|---|---|---|---|
| Integrated Control
(Estimates driver requested torque based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.) |
ECM | Brake actuator assembly (skid control ECU) | Torque requested based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are not improved. | Torque requested based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are not improved. | - |
| Anti-lock Brake System Control
(Prevents the wheels from locking during sudden stops.) |
Brake actuator assembly (skid control ECU) | Airbag ECU assembly, Translate ECU assembly | ·
During control: After ending backup control (stabilizing the vehicle behavior), the system changes to normal braking and prohibits control. ·
Control not operating: Control cannot start. |
The ABS warning light illuminates. | ·
U0073 ·
U0124 [Brake actuator assembly (skid control ECU)] |
| Vehicle Stability Control/Traction Control
(Suppresses vehicle instability, such as drift when cornering and wheel slippage when accelerating. During vehicle dynamics integrated management control, vehicle integrated control which includes electronic steering control is performed.) |
Brake actuator assembly (skid control ECU) | ECM, Airbag ECU assembly, Spiral with sensor cable sub-assembly (steering angle sensor), Translate ECU assembly | ·
During control: After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control. ·
Not during control: Control cannot start. |
·
The ABS warning light illuminates. ·
The SLIP indicator light illuminates. |
·
U0073 ·
U0100 ·
U0124 ·
U0126 [Brake actuator assembly (skid control ECU)] |
| Hill-start Assist Control 3
(Maintains the brake oil pressure for 2 seconds when the brake pedal is depressed further.) |
Brake actuator assembly (skid control ECU) | ECM, Airbag ECU assembly, Spiral with sensor cable sub-assembly (steering angle sensor) | ·
During control: After ending backup control (pressure reduction control), the system changes to normal braking and prohibits control, or control continues, and after normal control finishes, prohibits control. ·
Not during control: Control cannot start. |
·
The ABS warning light illuminates. ·
The SLIP indicator light illuminates. |
·
U0073 ·
U0100 ·
U0124 ·
U0126 [Brake actuator assembly (skid control ECU)] |
| Vehicle Speed Display
(Displays/sounds speedometer indications and speed warnings according to the vehicle speed signal information from the brake actuator assembly (skid control ECU).) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "0". | The speedometer displays 0 km/h. | U0129
[Combination meter assembly] |
| Tachometer
(Displays information on the tachometer.) |
Combination meter assembly | ECM | Signal is considered to be "0". | The speedometer displays 0 km/h. | U0100
[Combination meter assembly] |
| Fuel Gauge
(Displays the amount of remaining fuel.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "0". | Calculation continues using a provisional value. | U0129
[Combination meter assembly] |
| Engine System Display
(Turns the coolant temperature gauge command display/high temperature warning buzzer on and off.) |
Combination meter assembly | ECM | Signal is considered to be "0". | Sets the needle of the engine coolant temperature gauge at the C mark or below. | - |
| Odometer and Trip Meter Display
(Displays the driving distance.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "0". | The last displayed value remains. | U0129
[Combination meter assembly] |
| Airbag
(Turns the ABS warning light on and off.) |
Combination meter assembly | Airbag ECU assembly | Signal is considered to be "Active". | SRS warning light illuminates. | U0151
[Combination meter assembly] |
| ABS Warning
(Turns the ABS warning light on and off.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "Active". | The ABS warning light illuminates. | U0129
[Combination meter assembly] |
| Brake Warning
(Turns the brake warning light on and off.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "Active". | The brake warning light illuminates. | U0129
[Combination meter assembly] |
| SLIP Indicator
(Turns the SLIP warning light on and off.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | Signal is considered to be "Active". | The slip indicator light illuminates. | U0129
[Combination meter assembly] |
| TRC OFF
(Turns the TRC OFF warning light on and off.) |
Combination meter assembly | Brake actuator assembly (skid control ECU) | While ignition switch is ON, the current status is maintained. | Nothing | U0129
[Combination meter assembly] |
| TC DTC Output Service
(While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.) |
Combination meter assembly | ECM | When reception of the TC signal is lost during the TC service (TC = ON), this is regarded as TC = OFF and the TC service ends. | The MIL illuminates. (for 2TR-FE) | - |
| Timestamp
(Stores the timestamp information received from the central gateway ECU [network gateway ECU] together with the DTC.) |
Airbag ECU assembly | Central gateway ECU (network gateway ECU) | Changes to a separate count inside the ECU and sets separate count recognition information when it receives a fail value or communication stops | Nothing | - |
| Collision Detection Signal
(Reports a collision in order to perform a fuel cut, trigger the EDR, perform MCB control, etc. during a collision.) |
ECM, brake actuator assembly (skid control ECU) | Airbag ECU assembly | - | Nothing | - |
| Airbag Warning Control
(Sends SRS warning light illumination information.) |
Combination meter assembly | Airbag ECU assembly | - | Nothing | - |
| Trigger Signal/Self Transmission
(Outputs the yaw rate and acceleration sensor signal.) |
Airbag ECU assembly | Brake actuator assembly (skid control ECU) | Data is periodically transmitted every 0.012 seconds. | Nothing | - |
| Event Data Recorder (EDR)
(Records conditions, such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
Airbag ECU assembly | ECM, Spiral with sensor cable sub-assembly (steering angle sensor), Brake actuator assembly (skid control ECU) | ·
An invalid value is recorded in the EDR. ·
Maintains previous values |
Nothing | - |
| Drive Data Recorder (DDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the drive data recorder recording conditions are met.) |
Airbag ECU assembly | ECM, Combination meter assembly, Spiral with sensor cable sub-assembly (steering angle sensor), Brake actuator assembly (skid control ECU) | ·
An invalid value is recorded in the DDR. ·
Maintains previous values. |
Nothing | - |
| Lost Communication Detection
(The NS and NM frames of the ECU connected to the global bus are monitored to detect for ECU communication failures.) |
Central gateway ECU (network gateway ECU) | ECUs connected to the global bus | Records the communication failure time. | Nothing | - |
| Steering Angle Output
(Detects the steering wheel angle.) |
Spiral with sensor cable sub-assembly (steering angle sensor) | Brake actuator assembly (skid control ECU) | Data is periodically transmitted every 0.012 seconds. | Nothing | - |