Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2019.08–2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Detection Item Trouble Area

*1: except N04C-WA

*2: for N04C-WA

*3: for N04C-WA with Automatic Transmission

No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main wires

·

Short to +B in CAN branch wires

·

Central gateway ECU (network gateway ECU)

·

ECM*1

·

Translate ECU assembly*2

·

Transmission control ECU assembly*3

·

No. 66 junction connector*1

·

No. 7 CAN junction connector*2



WIRING DIAGRAM

except N04C-WA
C400782E02
0.854,0.365 1.469,0.563 0.615,0.198 10 false CA4H 0.885,1.104 1.5,1.302 0.615,0.198 10 false CA4L 0.167,1.427 0.781,1.625 0.615,0.198 10 false J51 0.146,1.604 1.646,1.99 1.5,0.385 10 false Central Gateway ECU (Network Gateway ECU) 2.563,1.375 3.177,1.573 0.615,0.198 10 false A85 2.563,1.531 4.292,1.771 1.729,0.24 10 false No. 66 Junction Connector 5.958,0.375 6.573,0.573 0.615,0.198 10 false CANH 5.969,1.083 6.583,1.281 0.615,0.198 10 false CANL 1.833,2.458 2.969,2.646 1.135,0.188 10 false *1: for N04C-UH 3.094,2.448 4.844,2.625 1.75,0.177 10 false *2: for N04C-VQ, N04C-VL 4.938,2.438 6.177,2.646 1.24,0.208 10 false *3: for 2TR-FE 4.865,0.271 5.479,0.469 0.615,0.198 10 false 17*1 5.271,0.281 5.885,0.479 0.615,0.198 10 false 7*2 5.583,0.281 6.198,0.479 0.615,0.198 10 false 33*3 5.604,0.813 6.219,1.01 0.615,0.198 10 false 34*3 5.26,0.813 5.875,1.01 0.615,0.198 10 false 1*2 4.865,0.813 5.479,1.01 0.615,0.198 10 false 28*1 6.26,1.406 6.719,1.604 0.458,0.198 10 false ECM 4.896,0.479 5.354,0.677 0.458,0.198 10 false A52 4.885,1 5.344,1.198 0.458,0.198 10 false A52 5.25,0.469 5.708,0.667 0.458,0.198 10 false A56 5.625,0.469 6.083,0.667 0.458,0.198 10 false A53 5.625,1 6.083,1.198 0.458,0.198 10 false A53 5.25,1 5.708,1.198 0.458,0.198 10 false A56 1.323,0.375 1.635,0.573 0.313,0.198 10 false 18 1.333,0.906 1.646,1.104 0.313,0.198 10 false 17 3.24,0.375 3.552,0.573 0.313,0.198 10 false 3 3.177,0.917 3.49,1.115 0.313,0.198 10 false 14 3.833,0.385 4.146,0.583 0.313,0.198 10 false 1 3.823,0.917 4.135,1.115 0.313,0.198 10 false 12

for N04C-WA
C422185E01
1.302,0.698 1.615,0.896 0.313,0.198 10 false 18 1.313,1.229 1.625,1.427 0.313,0.198 10 false 17 3.052,0.688 3.365,0.885 0.313,0.198 10 false 5 2.979,1.24 3.292,1.438 0.313,0.198 10 false 16 3.844,0.698 4.156,0.896 0.313,0.198 10 false 6 3.854,1.24 4.167,1.438 0.313,0.198 10 false 17 5.719,0.698 6.031,0.896 0.313,0.198 10 false 31 5.708,1.25 6.021,1.448 0.313,0.198 10 false 32 5.698,3.458 6.01,3.656 0.313,0.198 10 false 11 5.698,4 6.01,4.198 0.313,0.198 10 false 12 4.76,3.49 5.073,3.688 0.313,0.198 10 false * 4.781,4.021 5.094,4.219 0.313,0.198 10 false * 3.844,3.448 4.156,3.646 0.313,0.198 10 false 7 3.823,4 4.135,4.198 0.313,0.198 10 false 18 0.094,1.75 0.552,1.948 0.458,0.198 10 false J51 5.313,1.635 5.771,1.833 0.458,0.198 10 false V9 2.635,4.458 3.094,4.656 0.458,0.198 10 false A123 5.354,4.385 5.813,4.583 0.458,0.198 10 false B133 0.083,1.906 2.104,2.323 2.021,0.417 10 false Central Gateway ECU (Network Gateway ECU) 5.313,1.802 6.99,2.177 1.677,0.375 10 false Translate ECU Assembly 2.635,4.604 4.573,4.948 1.938,0.344 10 false No. 7 CAN Junction Connector 5.354,4.542 7,5.104 1.646,0.563 10 false Transmission Control ECU Assembly* 0.146,5.417 2.292,5.615 2.146,0.198 10 false *: for Automatic Transmission 0.844,0.698 1.458,0.896 0.615,0.198 10 false CA4H 0.854,1.417 1.469,1.615 0.615,0.198 10 false CA4L 5.958,0.708 6.573,0.906 0.615,0.198 10 false CAN+ 5.958,1.417 6.573,1.615 0.615,0.198 10 false CAN- 5.969,3.563 6.583,3.76 0.615,0.198 10 false CANH 5.969,4.104 6.583,4.302 0.615,0.198 10 false CANL

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
except N04C-WA A
for N04C-WA B



A

2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 66 JUNCTION CONNECTOR)

B

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 66 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 66 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C358918E01
1.552,0.156 1.906,0.427 0.354,0.271 5.156,0.135 5.51,0.406 0.354,0.271 1.438,0.969 1.146,0.49 1.146,0.49 0.979,0.49 true 1.208,0.969 0.854,0.781 0.854,0.781 0.677,0.781 true 1.188,1.188 0.885,1.427 0.885,1.427 0.729,1.427 true 1.438,1.167 1.302,1.635 1.302,1.635 1.135,1.635 true 5.906,1.104 6.052,1.573 6.052,1.573 6.219,1.573 true 0.396,0.396 1.313,0.594 0.917,0.198 10 false CANH*d 0.115,0.698 1.031,0.896 0.917,0.198 10 false CANH*c 0.188,1.333 1.104,1.531 0.917,0.198 10 false CANL*c 0.604,1.552 1.521,1.75 0.917,0.198 10 false CANL*d 6.281,1.49 6.802,1.708 0.521,0.219 10 false BAT 5.229,0.188 6.146,0.385 0.917,0.198 10 false J45 1.615,0.208 2.531,0.406 0.917,0.198 10 false A85 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.115 4.469,0.313 0.313,0.198 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to No. 66 Junction Connector)
*b Front view of DLC3
*c to ECM *d to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A85-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
A85-12 (CANL) - J45-16 (BAT)
A85-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
A85-14 (CANL) - J45-16 (BAT)



Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN main wires) C



A

REPLACE NO. 66 JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)
a.

Reconnect the A85 No. 66 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C338146E35
0.146,3.229 0.49,3.51 0.344,0.281 1.49,0.354 1.833,0.635 0.344,0.281 2.031,2.458 1.865,2.458 1.865,2.458 1.656,1.521 true 2.708,4.354 2.542,4.354 2.542,4.354 2.375,3.708 true 2.125,2.177 1.958,2.177 1.958,2.177 1.792,1.531 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.125,2.542 0.438,2.74 0.313,0.198 10 false *b 1.552,0.417 1.948,0.615 0.396,0.198 10 false J51 0.208,3.281 0.604,3.479 0.396,0.198 10 false J45 2.115,2.385 2.729,2.583 0.615,0.198 10 false CA4L 2.198,2.094 2.813,2.292 0.615,0.198 10 false CA4H 2.792,4.281 3.406,4.479 0.615,0.198 10 false BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-17 (CA4L) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 7 CAN junction connector.

C358918N03
0.156,0.708 0.563,1.01 0.406,0.302 5.125,0.125 5.542,0.396 0.417,0.271 6.219,1.625 6.073,1.625 6.073,1.625 5.906,1.125 true 1.906,0.969 2.125,0.323 2.125,0.323 2.281,0.323 true 1.781,1 1.594,0.208 1.594,0.208 1.448,0.208 true 1.698,0.99 1.427,0.375 1.427,0.375 1.313,0.375 true 1.313,1.438 1.427,1.438 1.427,1.438 1.667,1.177 true 1.5,1.646 1.635,1.646 1.635,1.646 1.781,1.167 true 2.229,1.583 2.063,1.583 2.063,1.583 1.896,1.177 true 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 3.875,0.125 4.188,0.323 0.313,0.198 10 false *b 0.208,0.781 0.667,0.979 0.458,0.198 10 false A123 6.292,1.563 6.75,1.76 0.458,0.198 10 false BAT 5.229,0.188 5.688,0.385 0.458,0.198 10 false J45 0.906,0.135 1.823,0.333 0.917,0.198 10 false CANH*d 0.771,0.313 1.688,0.51 0.917,0.198 10 false CANH*c 2.313,0.26 3.229,0.458 0.917,0.198 10 false CANH*e 2.281,1.51 3.198,1.708 0.917,0.198 10 false CANL*e 0.781,1.365 1.698,1.563 0.917,0.198 10 false CANL*c 0.969,1.573 1.885,1.771 0.917,0.198 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU) *d to Translate ECU Assembly
*e to Transmission Control ECU Assembly (for Automatic Transmission) - -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*: for Automatic Transmission

A123-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
A123-16 (CANL) - J45-16 (BAT)
A123-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Translate ECU assembly
A123-17 (CANL) - J45-16 (BAT)
A123-7 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Transmission control ECU assembly*
A123-18 (CANL) - J45-16 (BAT)



d.

Reconnect the No. 7 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the central gateway ECU (network gateway ECU) connector.


b.
C338146E35
0.146,3.229 0.49,3.51 0.344,0.281 1.49,0.354 1.833,0.635 0.344,0.281 2.031,2.458 1.865,2.458 1.865,2.458 1.656,1.521 true 2.708,4.354 2.542,4.354 2.542,4.354 2.375,3.708 true 2.125,2.177 1.958,2.177 1.958,2.177 1.792,1.531 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.125,2.542 0.438,2.74 0.313,0.198 10 false *b 1.552,0.417 1.948,0.615 0.396,0.198 10 false J51 0.208,3.281 0.604,3.479 0.396,0.198 10 false J45 2.115,2.385 2.729,2.583 0.615,0.198 10 false CA4L 2.198,2.094 2.813,2.292 0.615,0.198 10 false CA4H 2.792,4.281 3.406,4.479 0.615,0.198 10 false BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-17 (CA4L) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464E28
1.469,0.271 1.865,0.521 0.396,0.25 1.458,2.406 1.854,2.656 0.396,0.25 2.146,1.979 1.99,1.979 1.99,1.979 1.677,1.156 true 2.448,1.698 2.302,1.698 2.302,1.698 1.76,1.156 true 2.719,3.948 2.573,3.948 2.573,3.948 2.354,3.646 true 1.563,0.313 2.021,0.51 0.458,0.198 10 false J51 1.542,2.448 2,2.646 0.458,0.198 10 false J45 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.146,2.271 0.604,2.469 0.458,0.198 10 false *b 2.531,1.625 2.99,1.823 0.458,0.198 10 false CA4L 2.219,1.896 2.677,2.094 0.458,0.198 10 false CA4H 2.802,3.875 3.26,4.073 0.458,0.198 10 false BAT

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-17 (CA4L) - J45-16 (BAT)


Text in Illustration
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR