1.INSPECT VALVE ROCKER ARM OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the rocker arm bush.
22.023 to 22.052 mm (0.867 to 0.868 in.)
22.08 mm (0.869 in.)
Using a micrometer, measure the outside diameter of the No. 1 valve rocker arm shaft sub-assembly.
21.959 to 21.980 mm (0.8645 to 0.8653 in.)
21.92 mm (0.863 in.)
Subtract the valve rocker arm inside diameter measurement from the valve rocker shaft outside diameter measurement.
0.043 to 0.093 mm (0.00169 to 0.00366 in.)
0.15 mm (0.00591 in.)
If the oil clearance is greater than the maximum, replace the No. 1 valve rocker arm shaft sub-assembly and valve rocker arm bush.
13781
2.INSPECT VALVE PUSH ROD
Place the push rod on V-blocks.
Using a dial indicator, measure the circle runout at the center of the push rod.
0.30 mm (0.0118 in.)
If the circle runout is greater than the maximum, replace the push rod.
11101A
3.INSPECT CYLINDER HEAD SET BOLT
Measure the length of the M12 head bolts (No. 1 to No. 18).
126 mm (4.96 in.)
129 mm (5.08 in.)
|
If the length is greater than the maximum, replace the applicable bolts. |
|
| *a | Measurement Length |
4.INSPECT NO. 2 IDLE GEAR OIL CLEARANCE
Using a cylinder gauge, measure the inside diameter of the No. 2 idle gear sub-assembly.
50.000 to 50.025 mm (1.9685 to 1.9695 in.)
50.05 mm (1.9704 in.)
Using a micrometer, measure the diameter of the No. 2 idle gear shaft.
49.950 to 49.975 mm (1.9665 to 1.9675 in.)
49.95 mm (1.9665 in.)
Subtract the No. 2 idle gear inside diameter measurement from the No. 2 idle gear shaft diameter measurement.
0.0125 to 0.0375 mm (0.000492 to 0.00148 in.)
0.10 mm (0.00394 in.)
If the clearance is greater than the maximum, replace the No. 2 idle gear sub-assembly and No. 2 idle gear shaft.
5.INSPECT NO. 1 IDLE GEAR OIL CLEARANCE
Using a cylinder gauge, measure the inside diameter of the No. 1 idle gear sub-assembly.
50.000 to 50.025 mm (1.9685 to 1.9695 in.)
50.05 mm (1.9704 in.)
Using a micrometer, measure the diameter of the No. 1 idle gear shaft.
49.950 to 49.975 mm (1.9665 to 1.9675 in.)
49.95 mm (1.9665 in.)
Subtract the No. 1 idle gear inside diameter measurement from the No. 1 idle gear shaft outside diameter measurement.
0.0125 to 0.0370 mm (0.000492 to 0.00146 in.)
0.10 mm (0.00394 in.)
If the clearance is greater than the maximum, replace the No. 1 idle gear sub-assembly and No. 1 idle gear shaft.
13265
6.INSPECT CONNECTING ROD BOLT
Using a vernier caliper, measure the length of the connecting rod bolt.
58.8 to 59.00 mm (2.315 to 2.323 in.)
61.5 mm (2.421 in.)
|
If the diameter is greater than the maximum, replace the connecting rod bolt. |
|
| *a | Measurement Length |
11462
7.INSPECT CYLINDER LINER
| *a | Symbol |
| *b | 20 mm (0.787 in.) |
|
Measuring Point |
Using a micrometer, measure the outside diameter of the cylinder liner.
| Symbol | Outside Diameter |
|---|---|
| A | 106.982 to 106.989 mm (4.2119 to 4.2122 in.) |
| B | 106.990 to 106.995 mm (4.2122 to 4.2124 in.) |
| C | 106.996 to 107.004 mm (4.2124 to 4.2128 in.) |
If the diameter is less than the standard, replace the cylinder liner.
| *a | Symbol |
| *b | Cylinder head Side |
| *c | Intake Manifold Side |
Using a cylinder gauge, measure the inside diameter of the cylinder block.
| Symbol | Inside Diameter |
|---|---|
| A | 107.000 to 107.008 mm (4.2126 to 4.2129 in.) |
| B | 107.008 to 107.014 mm (4.2129 to 4.2131 in.) |
| C | 107.014 to 107.022 mm (4.2131 to 4.2135 in.) |
If the diameter is more than the standard, replace the cylinder block.
8.INSPECT CYLINDER BLOCK FOR WARPAGE
Using a scraper, scrape along the circumference of the cylinder liner and remove any carbon attached to the inner surface near the top of the cylinder liner.
Make sure to adhere to the following precautions, as the intrusion of foreign matter may cause an engine malfunction.
Do not damage the surfaces under the attached carbon.
Make sure to sufficiently remove any foreign matter and shavings.
Do not use sandpaper. The intrusion of foreign matter may cause an engine malfunction
Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.
0.10 mm (0.00394 in.)
If the warpage is greater than the maximum, replace the cylinder block.
Visually check the cylinders for vertical scratches.
If deep scratches are found, rebore all 4 cylinders. If necessary, replace the cylinder block.
9.INSPECT CYLINDER BORE
| *a | 80 mm (3.15 in.) |
Using a cylinder gauge, measure the cylinder liner inside diameter at the 4 points shown in the illustration.
104.012 to 104.036 mm (4.0950 to 4.0959 in.)
104.15 mm (4.1004 in.)
If the diameter is greater than the maximum, replace the cylinder liner with a new one.
10.INSPECT PISTON
Using a micrometer, measure the piston diameter at the point in the illustration.
103.936 to 103.952 mm (4.0920 to 4.0926 in.)
| *a | Diameter |
| *b | Measurement Point (17 mm (0.669 in.)) |
11.INSPECT PISTON OIL CLEARANCE
Subtract the piston diameter measurement from the cylinder liner inside diameter measurement.
0.06 to 0.10 mm (0.00236 to 0.00394 in.)
Apply the value measured at the most worn point to the cylinder liner inside diameter.
If the clearance is outside the specified range, replace the cylinder liner and/or piston with a new one.
12.INSPECT RING GROOVE CLEARANCE
Insert the piston ring into the piston ring groove.
Using a feeler gauge, measure the clearance between the piston ring and piston ring groove.
| Item | Specified Condition |
|---|---|
|
If the result is not as specified, replace the piston ring or piston. |
|
| 1st | 0.11 to 0.15 mm (0.00433 to 0.00591 in.) |
| 2nd | 0.07 to 0.11 mm (0.00276 to 0.00433 in.) |
| Oil | 0.02 to 0.06 mm (0.000787 to 0.00236 in.) |
13.INSPECT PISTON RING END GAP
Install the cylinder liner to the cylinder block sub-assembly.
Insert the piston ring into the cylinder liner.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 80 mm (3.14 in.) from the top of the cylinder liner.
Using a feeler gauge, measure the piston ring end gap.
| Item | Specified Condition |
|---|---|
| No. 1 Compression Ring | 0.30 to 0.45 mm (0.0118 to 0.0177 in.) |
| No. 2 Compression Ring | 0.50 to 0.65 mm (0.0197 to 0.0256 in.) |
| Oil Ring | 0.15 to 0.30 mm (0.00591 to 0.0118 in.) |
If the result is not specified, replace the piston ring set.
If the piston ring end gap is more than the maximum even with a new piston ring set, replace the cylinder liner.
14.INSPECT CONNECTING ROD SUB-ASSEMBLY
Insert a stick with a diameter of 6 mm (0.24 in.) into the oil hole in the big end of the connecting rod and check that the tip of the stick comes out from the small end oil hole.
|
If there is any clogging, blow air through the lubrication passage using an air gun, or clean by inserting a wire. |
|
| *a | Stick (6 mm (0.24 in.)) |
Using a dye penetrant, check if there are any cracks on the connecting rod sub-assembly.
13411
15.INSPECT CRANKSHAFT
Before the inspection, clean the crankshaft with a commercial cleaning agent and clean the lubrication passage using an air gun.
| *1 | Air Gun |
Performing the dye penetrant test, check the crankshaft for cracks.
Pay special attention to the finished R section and oil hole of the crankshaft journal and crankshaft pin.
Visually check the crankshaft journal and pin for damage or wear.
If any damage is found, replace the crankshaft with a new one.
Inspect for runout.
Place the crankshaft on V-blocks.
Using a dial gauge, measure the circle runout of the crankshaft at the center journal.
0.04 mm (0.00157 in.)
If the circle runout is greater than the maximum, replace the crankshaft with a new one.
Using a micrometer, measure the main journal outside diameter.
72.94 to 72.96 mm (2.8717 to 2.8724 in.)
0.01 mm (0.000394 in.)
0.2 mm (0.00787 in.)
1.2 mm (0.04724 in.)
When the tapered level, out-of-round level, or wear limit is exceeded, use an undersized bearing and correct or re-polish until the oil clearance is 0.2 mm (0.00787 in.) or less (only carry out the correction/re-polishing if the oil clearance is over 0.2 mm (0.00787 in.) and under 1.2 mm (0.0472 in.)).
When the wear limit 1.2 mm (0.0472 in.) is exceeded, replace the crankshaft.
When polishing the crankshaft, adjust the fillet "R" dimensions to between 2.5 and 3.0 mm (0.0787 and 0.118 in.).
| *a | CORRECT |
| *b | INCORRECT |
Using a micrometer, measure the crankshaft pin outside diameter.
61.94 to 61.96 mm (2.4386 to 2.4394 in.)
0.01 mm (0.000394 in.)
0.2 mm (0.00787 in.)
1.2 mm (0.04724 in.)
When the tapered level, out-of-round level, or wear limit is exceeded, use an undersized bearing and correct or re-polish until the oil clearance is 0.2 mm (0.00787 in.) or less (only carry out the correction/re-polishing if the oil clearance is over 0.2 mm (0.00787 in.) and under 1.2 mm (0.0472 in.)).
When the wear limit 1.2 mm (0.0472 in.) is exceeded, replace the crankshaft.
When polishing the crankshaft, adjust the fillet "R" dimensions to between 2.5 and 3.0 mm (0.0787 and 0.118 in.).
| *a | CORRECT |
| *b | INCORRECT |
Using a vernier caliper, measure the width of the crankshaft No. 4 journal.
34.00 to 34.08 mm (1.3386 to 1.3417 in.)
34.48 mm (1.3574 in.)
If the width is greater than the maximum, replace the crankshaft.
Using a dye penetrant, check if there are any cracks on the crankshaft.
If any blockage is found, replace the crankshaft.
11416
16.INSPECT CRANKSHAFT BEARING CAP SET BOLT
Using a vernier caliper, measure the bearing cap bolt length.
92.80 to 93.80 mm (3.6535 to 3.6929 in.)
95.00 mm (3.7401 in.)
|
If the length is longer than the maximum, replace the crankshaft bearing cap set bolt. |
|
| *a | Measurement Length |
17.INSPECT CRANKSHAFT OIL CLEARANCE
The upper bearings have an oil groove and oil hole, however, the lower bearings do not.
| *1 | Oil Hole |
Align the claw of the bearing with the claw groove of the cylinder block, and push in the upper bearing.
Do not apply engine oil to the bearing and its contact surface.
Align the claw of the bearing with the claw groove of the main bearing cap, and push in the lower bearing.
Do not apply engine oil to the bearing and its contact surface.
Install the thrust washer and bearing cap attached with bearing onto the cylinder block.
| *a | Front Mark |
| *b | Journal No. |
Apply a light coat of engine oil to the threads and seat portion the heads of the bearing cap bolt.
Uniformly tighten the 10 bolts, in 2 to 3 steps in the order shown in the illustration.
60 N*m (612 kgf*cm, 44 ft.*lbf)
Loosen the bearing cap in the position of the thrust washer and use a plastic-faced hammer to lightly tap the front and back ends of the crankshaft.
Loosen the 10 bolts.
Tighten the 10 bolts, in 2 to 3 steps in the order shown in the illustration.
60 N*m (612 kgf*cm, 44 ft.*lbf)
Mark the front side of the bolts with paint.
| *a | Paint Mark |
|
Front |
Retighten the bolts by 60° in the same order as step (e).
Perform step (j) again.
Check that paint mark is now at a 120° angle to the front.
Do not loosen to return the bolts in position if they have been tightened too much.
Using a cylinder gauge, measure the crankshaft bearing inside diameter at 3 points (X, Y, Z in the illustration).
Do not damage the crankshaft bearing.
Subtract the crankshaft journal diameter measurement from the bearing inside diameter measurement.
0.051 to 0.102 mm (0.00201 to 0.00402 in.)
0.20 mm (0.00787 in.)
If the oil clearance is greater than the maximum, use an undersize bearing and correct or regrind the crankshaft so that the oil clearance becomes 0.20 mm (0.0078 in.) or less.
| Item | Specified Condition |
|---|---|
| STD | 72.94 to 72.96 mm (2.8717 to 2.8724 in.) |
| U/S 0.25 | 72.69 to 72.71 mm (2.8618 to 2.8626 in.) |
| U/S 0.50 | 72.44 to 72.46 mm (2.8520 to 2.8528 in.) |
| U/S 0.75 | 72.19 to 72.21 mm (2.8421 to 2.8429 in.) |
| U/S 1.00 | 71.94 to 71.96 mm (2.8323 to 2.8330 in.) |
Replace the upper and lower main bearings as one set.
Machined dimension of file R
2.50 to 3.00 mm (0.0984 to 0.1181 in.)
| *a | CORRECT |
| *b | INCORRECT |
18.INSPECT CONNECTING ROD BEARING OIL CLEARANCE
| *a | Claw |
Align the claw of the bearing with the claw grooves of the connecting rod and connecting cap.
Clean the back side of the bearing and the bearing surface of the connecting rod. The surface should be free of dust and oil.
Tighten the connecting rod bolts.
Check the matchmarks, and install the bearing caps.
Be careful of the installation direction of the bearing caps.
| *a | Matchmarks |
Uniformly tighten the bolts in 2 to 3 steps.
Retighten the connecting rod bolts.
30 N*m (306 kgf*cm, 22 ft.*lbf)
Mark the front side of the bolts with paint.
| *a | Paint Mark |
|
Front |
Retighten the bolts by 60° in the same order as step (b).
Perform step (c) again.
Using a cylinder gauge, measure the connecting rod big end inside diameter.
Be careful not to damage the connecting rod bearing.
Subtract the inside diameter measurement of the connecting rod from the diameter measurement of the crankshaft pin.
0.031 to 0.082 mm (0.00122 to 0.00323 in.)
0.20 mm (0.00787 in.)
If the result is greater than the maximum, use an undersize bearing and correct or regrind the crankshaft so that the oil clearance becomes 0.2 mm (0.0079 in.) or less.
| Item | Specified Condition |
|---|---|
| STD | 61.94 to 61.96 mm (2.4386 to 2.4394 in.) |
| U/S 0.25 | 61.69 to 61.71 mm (2.4287 to 2.4295 in.) |
| U/S 0.50 | 61.44 to 61.46 mm (2.4189 to 2.4197 in.) |
| U/S 0.75 | 61.19 to 61.21 mm (2.4090 to 2.4098 in.) |
| U/S 1.00 | 60.94 to 60.96 mm (2.3992 to 2.4000 in.) |
Machined dimension of file R
2.50 to 3.00 mm (0.0984 to 0.1181 in.)
| *a | CORRECT |
| *b | INCORRECT |