Home › Engine / Hybrid System › N04C-WA (INTAKE) › INTAKE SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082615 N04C-WA INTAKE _0403719 INTAKE SYSTEM G

N04C-WA INTAKE  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK TURBOCHARGER PRESSURE

a.
A447437C02
1.448,0.375 1.281,0.375 1.281,0.375 1.281,1.344 true 2.51,0.396 2.344,0.396 2.344,0.396 2.344,0.625 true 1.49,0.281 1.833,0.479 0.344,0.198 10 true SST 2.531,0.292 2.74,0.49 0.208,0.198 10 true *1
*1 Manifold Absolute Pressure Sensor


Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose leading to the intake manifold.

SST
09992-00242  


b.

Fully apply the parking brake and chock the 4 wheels.


c.

While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 3480 to 3580 rpm).

Standard pressure (Gauge pressure):

30 to 70 kPa (0.3 to 0.7 kgf/cm2, 4 to 10 psi)



Hide 2.INSPECT TURBOCHARGER SUB-ASSEMBLY

a.

Remove the No. 1 turbo insulator.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


b.

Check stroke

i.

Check that the DC motor connector is properly installed.


ii.

When turning the ignition switch from ON to off, check that the variable nozzle operation link operates.

NOTICE:

The lock nuts of the turbocharger fully open and fully closed stoppers do not loosen or tighten.


HINT:

When turning the ignition switch off, the variable nozzle operation link operates as shown in the illustration.

A257099




c.

Install the No. 1 turbo insulator.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>INSTALLATION


Hide 3.INSPECT TURBOCHARGER CONTROL ACTUATOR

a.

Check the voltage of the turbocharger sub-assembly control actuator.

i.

Disconnect the turbocharger sub-assembly connector.


ii.

Turn the ignition switch to ON.


iii.
A227776C04
1.333,1.292 1,1.74 true 1.677,1.302 1.979,1.75 true 0.5,0.292 0.719,0.5 0.219,0.208 10 false *a 0.854,1.771 1.125,1.979 0.271,0.208 10 false +B 1.927,1.781 2.313,2 0.385,0.219 10 false GND
*a Front view of wire harness connector
(to Turbocharger Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
1(+B) - 2(GND) Ignition switch ON 11 to 14 V


If the voltage is not as specified, check the wire harness and connector.



Hide 4.INSPECT INTAKE SYSTEM

a.

Check that there is no air suction or leaks at the points shown in the illustration.

A451169C02
5.698,4.396 6.073,4.396 true 1.969,4.896 2.344,4.896 true 0.375,4.073 0.646,4.073 true 0.688,3.365 1.063,3.365 true 1.708,3.938 1.948,3.938 true 5.823,1.313 6.094,1.26 6.094,1.26 6.354,1.26 true 4.563,2.885 4.656,2.885 4.656,2.885 4.802,3.865 true 5.729,0.823 5.927,1 0.198,0.177 10 false *1 6.396,1.198 6.615,1.365 0.219,0.167 10 false *2 6.115,4.333 6.354,4.5 0.24,0.167 10 false *3 4.385,2.823 4.573,3 0.188,0.177 10 false *4 3.063,1.479 3.26,1.667 0.198,0.188 10 false *5 3.063,2.458 3.281,2.635 0.219,0.177 10 false *6 2.927,3.49 3.156,3.667 0.229,0.177 10 false *7 0.479,3.302 0.688,3.49 0.208,0.188 10 false *8 0.177,4.01 0.375,4.177 0.198,0.167 10 false *9 1.438,3.875 1.719,4.042 0.281,0.167 10 false *10 1.698,4.833 1.979,5.021 0.281,0.188 10 false *11
*1 Air Cleaner Assembly *2 Mass Air Flow Meter Sub-assembly
*3 PCV Hose Assembly *4 Turbocharger Sub-assembly
*5 Intercooler Assembly *6 EGR Cooler Sub-assembly
*7 Oil Separator Assembly *8 Diesel Throttle Body Assembly
*9 Manifold Absolute Pressure Sensor *10 EGR Valve Assembly
*11 Intake Manifold - -