1.INSTALL CAMSHAFT BEARING
| *a | No. 1 Camshaft Bearing |
| *b | No. 2 Camshaft Bearing |
| *c | No. 3 Camshaft Bearing |
| *d | Notch |
| *e | Oil Hole |
Be sure to face the notches of the No. 1 camshaft bearing and No. 2 camshaft bearing and oil holes of the No. 3 camshaft bearing in the correct direction.
| *a | No. 1 Journal |
| *b | No. 2 Journal |
| *c | No. 3 Journal |
|
Front |
Using SST, install new camshaft bearings in the direction indicated by the arrows in the illustration.
| Item | Inside Diameter | Outside Diameter |
|---|---|---|
| No. 1 journal | 57.0 mm (2.244 in.) | 60.0 mm (2.362 in.) |
| No. 2 journal | 56.8 mm (2.236 in.) | 59.8 mm (2.354 in.) |
| No. 3 journal | 56.6 mm (2.228 in.) | 59.6 mm (2.346 in.) |
Install the No. 2 journal, No. 1 journal and No. 3 journal in order.
13201A
2.INSTALL CONNECTING ROD SMALL END BUSH
Uniformly chamfer one edge of the bush hole at the small end of the connecting rod sub-assembly.
Incorrect chamfering can cause the connecting rod small end bush to become out-of-round, which may result in jamming during insertion.
Remove dust from the inner surface of the connecting rod hole.
| *a | SST (Spindle) |
| *b | Bush |
| *c | SST (Guide) |
| *d | SST (Bolt) |
| *e | Groove |
Install the new connecting rod small end bush to SST and tighten the bolt.
Align the groove of SST (spindle) with the groove of SST (press sub-assembly) to install SST.
Apply fresh engine oil to the connecting rod small end bush and guide.
| *a | SST (Guide) |
| *b | SST (Wing Nut) |
| *c | SST (Press Sub-assembly) |
Prepare SST.
Install the press sub-assembly to the guide by inserting the pin of the press sub-assembly into the guide, and then secure them together by installing the wing nut.
Orient the guide so that the letter W, which is stamped on the guide, is above the pin.
| *a | Groove |
With the connecting rod bearing removed, install the connecting rod bearing cap and place the connecting rod on SST with its chamfered side facing upward.
Place SST so that the groove of SST (press sub-assembly) is at the center of the connecting rod.
| *a | Groove |
Align the groove of SST (guide) with the groove of SST (press sub-assembly) to install the connecting rod small end bush using a press.
Align the groove of the SST (guide) with the groove of the SST (guide) with the groove of the SST (press sub-assembly) and install.
Inspect the connecting rod small end bush position after installation.
Make sure that the oil hole of the connecting rod small end bush and the oil path of the connecting rod are properly aligned, allowing a 6 mm (0.236 in.) diameter rod to pass through.
Misalignment can lead to insufficient lubrication, which may result in piston seizure.
With a new piston pin inserted in the piston, make sure that the pin can be rotated by hand and is not loose.
13101A
3.INSTALL PISTON PIN HOLE SNAP RING
Using snap ring pliers, install a new snap ring into one side of the piston hole.
4.INSTALL PISTON
Before assembling the piston with the connecting rod, check whether the piston is specified for this engine. The check should be performed using the engine compatible identification code on the top of the piston.
35
Assemble the piston and connecting rod.
Gradually heat the piston to approximately 50°C (122°F).
Do not touch the piston while it is hot.
Coat the piston pin with engine oil.
| *a | Notch |
| *b | Alignment Mark |
Install the piston onto the connecting rod with the notch on the piston facing in the same direction as the alignment mark on the rod. Then, secure them with the piston pin.
Check that the piston and piston pin fit securely.
Try to move the piston back and forth.
Using snap ring pliers, install a new snap ring into the other side of the piston pin hole.
13011
5.INSTALL PISTON RING SET
Face the identification marks on the piston ring up, then using a piston ring expander, install them in the following order of the oil ring, 2nd ring and 1st ring.
Never change the combination of the coil and oil ring.
Connect the joint of the coil expander for the oil ring and install it inside the oil ring. Align the expander joint 180° opposite to the gap of the ring.
15708
6.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Install the No. 1 oil nozzle sub-assembly with the bolt.
If the No. 1 oil nozzle sub-assembly has been dropped or any impact has occurred to the nozzle, replace the No. 1 oil nozzle sub-assembly.
Replace a deformed No. 1 oil nozzle assembly.
11271A
7.INSTALL REAR CYLINDER BLOCK COVER
Install a new O-ring and the rear cylinder block cover with the 2 bolts.
15605
8.INSTALL OIL CHECK VALVE SUB-ASSEMBLY
Install a new gasket and the oil check valve with the bolt.
11702
9.INSTALL CRANKSHAFT BEARING SET
| *a | Oil Hole |
Align the oil groove of the crankshaft bearing with the oil hole of the cylinder block sub-assembly, and push in the 5 upper crankshaft bearings.
Keep the back side of the crankshaft bearing and the crankshaft bearing surface free of foreign matter.
Align the crankshaft bearing with the crankshaft bearing cap, and push in the 5 lower crankshaft bearings.
Keep the back side of the crankshaft bearing and the crankshaft bearing surface free of foreign matter.
Install the crankshaft.
| *a | Groove |
Insert the crankshaft thrust washer into the clearance between the cylinder block sub-assembly and crankshaft with the oil groove facing outward.
Be sure to install the removed crankshaft thrust washer to its original position.
| *a | Front Mark |
| *b | Journal No. |
Install the crankshaft bearing caps onto the cylinder block sub-assembly.
When installing the crankshaft bearing caps, return them to their original locations according to the number stamped on the crankshaft bearing caps.
Apply a light coat of engine oil to the threads and under the crankshaft bearing cap bolt.
Step 1:
Temporarily install the bolts and tighten them in several steps in the sequence shown in the illustration.
Tighten the bolts to the specified torque.
Step 2:
Mark the front of the bearing cap bolts with paint.
Tighten the bolts 60°.
Step 3:
Tighten the bolts 60°.
Check that each paint mark is now at a 120° angle to the front.
11462
10.INSTALL CYLINDER LINER
When assembling the cylinder liner into the cylinder block sub-assembly, the clearance can be set to 3 levels.
| *a | Position of Mark A, B or C |
The upper surface and side surface of the cylinder block sub-assembly are stamped A, B or C. When using a new cylinder liner, insert a matching cylinder liner with the same symbol.
Apply engine oil to the cylinder block sub-assembly inside bore.
| *a | Mark |
Align the marks of the cylinder liner and cylinder block sub-assembly.
When reusing the cylinder liner, install it according to the marks made during the removal. When reusing the cylinder liner, misalignment with the cylinder block sub-assembly may concentrate stress on the thin part of the cylinder liner and it may break.
Install the cylinder liner.
Make sure to install the cylinder liner to its original location.
11.INSPECT PROTRUSION OF CYLINDER LINER
Mount SST onto the cylinder block sub-assembly.
Tighten the center bolt to the specified torque below to set SST in the proper installation position.
| *a | Protrusion |
Using a dial indicator, measure the protrusion of the cylinder liner.
0.01 to 0.08 mm (0.000394 to 0.00315 in.)
0.08 mm (0.00315 in.)
If the protrusion is more than the maximum, replace the cylinder liner.
13202
12.INSTALL CONNECTING ROD BEARING SET
When reusing the connecting rod bearing, reassemble the removed connecting rod bearing as it was originally installed.
Install the connecting rod bearing with the oil hole onto the connecting rod side and install the connecting rode bearing without the oil hole onto the connecting rod bearing cap side.
Match the connecting rod bearing protrusion with the notch of the connecting rod or connecting rod bearing cap.
Keep the back side of the connecting rod bearing and connecting rod bearing surface of the connecting rod bearing cap free of foreign matter.
13301A
13.INSTALL PISTON WITH CONNECTING ROD
| *1 | 2nd Ring |
| *2 | Oil Ring |
| *3 | Top Ring |
| *a | Mark |
Position the gaps of the piston rings at an even distance. Be careful not to position the gaps at the same position as the piston mark.
Using a piston ring compressor and a hammer handle, insert the piston with connecting rod assembly into the cylinder block sub-assembly.
Before the installation, apply engine oil to the piston pin, piston ring, cylinder liner and connecting rod bearing.
Recheck the gap of each piston ring.
Do not damage the inside of the liner.
Make sure that the mark on the piston is on the tappet chamber side.
Install the bearing cap onto the connecting rod with the "0" mark facing in the correct direction.
Step 1:
Apply a light coat of engine oil to the threads of the connecting rod cap bolts.
Install and uniformly tighten the connecting rod cap bolts to the specified torque in several steps.
Step 2:
Mark the front side of each connecting rod cap bolt with paint.
Tighten the connecting rod cap bolts 60°.
Step 3:
Tighten the connecting rod cap bolts an additional 60°.
Check that the paint marks are now at a 120° angle to the front.
11381A
14.INSTALL REAR ENGINE OIL SEAL
| *a | 4 mm (0.157 in.) |
Using SST and a hammer, tap in a new rear engine oil seal until it is 4 mm (0.157 in.) below the upper edge of the flywheel housing.
Be careful not to tap the rear engine oil seal at an angle.
Keep the gap between the rear oil seal retainer edge and the oil seal free of foreign matter.
Apply MP grease to the oil seal lip.
11351
15.INSTALL FLYWHEEL HOUSING
Remove any old seal packing material from the contact surface.
| *a | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
1.5 to 2.5 mm (0.0591 to 0.984 in.)
Remove any oil from the contact surface.
Install the flywheel housing within 3 minutes of applying the seal packing.
Do not expose the seal packing to engine oil for at least 2 hours after installation.
Install the flywheel housing with the 14 bolts.
13453
16.INSTALL FLYWHEEL RING GEAR
Using a torch, heat the flywheel ring gear evenly to approximately 200°C (392°F).
Be careful not to overheat the flywheel ring gear.
| *1 | Flywheel Ring Gear |
| *2 | Flywheel Assembly |
| *a | Chamfer |
| *b | 0.25 mm (0.00984 in.) or less |
Using a brass bar, strike the flywheel ring gear onto the flywheel assembly with its chamfered flywheel ring gear teeth facing the block.
0.25 mm (0.00984 in.) or less
After installing, allow the flywheel ring gear to cool before handling.
13450A
17.INSTALL FLYWHEEL ASSEMBLY
Insert the flywheel assembly slowly until it contacts the collar knock in order to prevent impact with the guide bar. Adjust the position, then insert it completely.
The flywheel assembly is heavy. When installing the flywheel assembly, be careful not to drop it.
Apply a light coat of engine oil to the threads of the flywheel bolts and flywheel bolt seats.
Temporarily install the flywheel assembly with the flywheel bolts.
Step 1:
Tighten the flywheel bolts in several steps in the order shown in the illustration.
Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to prevent the flywheel ring gear from turning together with the crankshaft.
Step 2:
Mark the top of each flywheel bolt head with paint.
Tighten the bolts 45° in the order shown in the illustration.
Check that the paint marks are now at a 45° angle to the top.
Using a dial indicator, measure the runout of the flywheel assembly.
0.15 mm (0.00591 in.)
If the runout is more than the maximum, resurface the sliding surface.
Temporarily install 4 bolts in the positions of the cylinder block sub-assembly shown in the illustration to prevent the wires from sliding toward the center of the cylinder block sub-assembly.
Attach 2 wires to the cylinder block sub-assembly.
The wires must be attached outside the installed bolts.
Using a chain block and an engine sling device, install the cylinder block sub-assembly onto the engine stand.
Remove the 4 bolts from the cylinder block sub-assembly.
11311H
18.INSTALL FRONT END PLATE
Install the front end plate with a new gasket and 4 bolts.
| *1 | Timing Gear Cover |
| *2 | Front End Plate |
| *3 | Gasket |
| *4 | Cylinder Block Sub-assembly |
| *a | Cutter |
| *b | Cut |
Using a cutter, cut the gasket so that it is flush with the lower surface of the cylinder block sub-assembly.
15100
19.INSTALL OIL PUMP ASSEMBLY
| *a | Engine Oil |
Apply engine oil to the oil pump case of the cylinder block sub-assembly shown in the illustration.
If engine oil is not applied, an oil suction malfunction will occur when starting the engine. The malfunction causes seizure or abnormal wear to the engine.
Install a new gasket and oil pump assembly with the 7 bolts.
Check that the oil pump rotates smoothly by hand after the installation.
13521
20.INSTALL CRANKSHAFT GEAR
| *a | No. 1, No. 4 Cylinder |
| *b | Alignment Mark |
Turn the crankshaft clockwise, and align the alignment mark on the flywheel assembly with the alignment mark between the 2 numbers on the edge of the flywheel housing to set the No. 1 cylinder to TDC/compression.
Align the set key on the crankshaft with the key groove of the crankshaft gear.
Using a hammer, tap on the crankshaft gear.
13572B
21.INSTALL NO. 1 IDLE GEAR THRUST PLATE
Install the No. 1 idle gear sub-assembly and No. 1 idle gear thrust plate onto the No. 1 idle gear shaft.
| *a | Alignment Mark |
With the No. 1 idle gear shaft oil hole facing down, match the alignment marks for each gear, and insert the shaft into the cylinder block sub-assembly.
| *a | Oil Hole |
If the oil hole is not facing down, it causes burning or abnormal wear.
Tighten the bolt.
13501
22.INSTALL CAMSHAFT SUB-ASSEMBLY
13581C
23.INSTALL NO. 2 IDLE GEAR SHAFT
| *a | Oil Hole |
Install the lock plate onto the front end plate with the 3 bolts.
Install a new O-ring onto the No. 2 idle gear shaft.
With the No. 2 idle gear shaft oil hole facing down, install the No. 2 idle gear shaft onto the lock plate with the 2 bolts.
If the oil hole is not facing down, it causes burning or abnormal wear.
13508N
24.INSTALL NO. 2 IDLE GEAR SUB-ASSEMBLY
| *a | Alignment Mark |
Match the alignment marks of the No. 1 idle gear sub-assembly and No. 2 idle gear sub-assembly and install the No. 2 idle gear sub-assembly.
13572C
25.INSTALL NO. 2 IDLE GEAR THRUST PLATE
Install the No. 2 idle gear thrust plate with the 2 bolts.
11301C
26.INSTALL FRONT CRANKSHAFT OIL SEAL
Using SST and a hammer, tap the new front crankshaft oil seal into the timing gear cover until the front crankshaft oil seal is flush with the timing gear cover edge.
Be careful not to tap the front crankshaft oil seal at an angle.
Keep the gap between the timing gear cover edge and the front crankshaft oil seal free of foreign matter.
Apply MP grease to the front crankshaft oil seal lip.
11321C
27.INSTALL TIMING GEAR COVER
Remove any old seal packing material from the contact surface.
| *a | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
1.5 to 2.5 mm (0.0591 to 0.0984 in.)
Remove any oil from the contact surface.
Install the timing gear cover within 3 minutes of applying the seal packing.
Do not expose the seal packing to engine oil for at least 2 hours after installation.
Install the timing gear cover with the 15 bolts.
13470
28.INSTALL CRANKSHAFT PULLEY ASSEMBLY
Install the crankshaft pulley and crankshaft pulley spacer onto the crankshaft.
Align the crankshaft pulley set key with the key groove of the crankshaft pulley.
Apply a light coat of engine oil to the threads of the nut.
Step 1:
Using a 46 mm socket wrench, tighten the nut.
Insert a screwdriver through the inspection hole of the flywheel housing into the flywheel ring gear of the flywheel assembly to keep it from turning together with the crankshaft.
Step 2:
Mark the top of each crankshaft pulley bolt head with paint.
Tighten the nut 90°.
Check that each paint mark is now at a 90° angle to the top.
15104
29.INSTALL OIL STRAINER SUB-ASSEMBLY
Install a new O-ring onto the cylinder block sub-assembly.
Install the strainer with the 2 bolts.
12101
30.INSTALL OIL PAN SUB-ASSEMBLY
Remove any old seal packing material from the contact surface.
| *a | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surface.
Install the oil pan sub-assembly within 3 minutes of applying the seal packing.
Do not expose the seal packing to engine oil for at least 2 hours after installation.
Install the oil pan sub-assembly with the 26 bolts.
11351H
31.INSTALL FLYWHEEL HOUSING STAY RH
Install the flywheel housing stay RH with the 4 bolts.
11351G
32.INSTALL FLYWHEEL HOUSING STAY LH
Install the flywheel housing stay LH with the 4 bolts.
13751
33.INSTALL VALVE LIFTER
Be sure to install the removed push rod to its original position.
11115
34.INSTALL CYLINDER HEAD GASKET
11101
35.INSTALL CYLINDER HEAD SUB-ASSEMBLY
13819
36.INSTALL VALVE BRIDGE
Be sure to install the removed valve bridge to its original location.
13781
37.INSTALL VALVE PUSH ROD
Be sure to install the removed valve bridge to its original location.
13901
38.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY
Install the No. 1 valve rocker arm sub-assembly, No. 2 valve rocker arm sub-assembly, No. 1 valve rocker support sub-assembly, No. 2 valve rocker support sub-assembly, and No. 3 valve rocker support sub-assembly to the No. 1 valve rocker shaft sub-assembly.
Make sure that the hole in the No. 1 valve rocker shaft is facing the cylinder head as shown in the illustration.
| *1 | No. 1 Valve Rocker Support Sub-assembly | *2 | No. 2 Valve Rocker Support Sub-assembly |
| *3 | No. 3 Valve Rocker Support Sub-assembly | *4 | No. 1 Valve Rocker Shaft Sub-assembly |
| *5 | No. 1 Valve Rocker Arm Sub-assembly | *6 | No. 2 Valve Rocker Arm Sub-assembly |
| *a | Cylinder Head Cover Side | *b | Cylinder Head Side |
|
Front | - | - |
Apply engine oil to the valve bridge and valve push rods.
Install the No. 1 valve rocker shaft sub-assembly to the cylinder head sub-assembly.
Apply engine oil to the seats and threads of the installation bolts, and tighten the bolts 1 to 2 threads by hand to determine the position.
Gradually tighten the bolts in several steps in the order shown in the illustration.
Make sure that the valve push rods do not interfere with the valve adjusting screws.
Check that the rocker arm moves smoothly after tightening.
Check that the valve bridge is not fallen off or shifted.
39.ADJUST VALVE CLEARANCE
| *a | TDC of No. 1 and No. 4 Cylinder |
| *b | TDC of No. 2 and No. 3 Cylinder |
| *c | Alignment Mark |
Flywheel housing side:
Turn the crankshaft clockwise to align the alignment mark on the flywheel assembly with the alignment mark between the 2 numbers on the edge of the flywheel housing.
| *a | TDC of No. 1 and No. 4 Cylinder |
| *b | TDC of No. 2 and No. 3 Cylinder |
| *c | Timing Mark |
| *d | Pointer |
Crankshaft pulley side:
Turn the crankshaft clockwise to align the alignment mark on the crankshaft pulley with the pointer on the timing gear cover.
If not, turn the crankshaft 1 revolution (360°) to align the timing mark with the pointer.
| *1 | Lock Nut |
| *a | Adjusting Screw |
| *b | Feeler Gauge |
With the No. 1 piston positioned at TDC on the compression stroke, adjust each valve clearance using a feeler gauge.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
The feeler gauge should move with a very slight pull.
Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.
Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust between the adjusting screw on the valve rocker arm and the valve bridge.
Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.
Recheck the clearance.
Adjust the other valves.
Turn the crankshaft 1 revolution (360°) clockwise.
Adjust the valve clearance for each cylinder in the firing order.
1 - 3 - 4 - 2
(The cylinder number is counted from the timing gear side)