Home › Vehicle Interior › AIR CONDITIONING › CONDENSER (except 1BZ-FPE) › 2019.08–2021.01
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0403620 CONDENSER(except 1BZ-FPE) A

AIR CONDITIONING  CONDENSER(except 1BZ-FPE)  INSTALLATION  


PROCEDURE

Hide 88450 1.INSTALL CONDENSER ASSEMBLY WITH RECEIVER

a.

Install the condenser assembly with receiver with the 6 bolts.

NOTICE:

Installing the condenser assembly with receiver to the vehicle must be performed by multiple people.


i.

for Front Side:

E424720C01
0.083,0.083 0.458,0.323 0.375,0.24 12 false *A 3.708,0.094 4.083,0.333 0.375,0.24 12 false *B
*A for RHD *B for LHD



ii.

for Rear Side:

E424721C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.75,0.094 4.083,0.333 0.333,0.24 12 false *B
*A for RHD *B for LHD




b.

Connect the 2 connectors.

E424716C01
0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.688,0.083 4,0.333 0.313,0.25 12 false *B
*A for RHD *B for LHD



Hide 88415L 2.INSTALL NO. 8 DUST COVER

a.

for Front Side:

i.

Install the No. 8 dust cover with the 3 clips in the order shown in the illustration.

E460099C01
0.125,0.104 7.073,5.729 6.948,5.625 0.292,0.458 6.917,2.792 6.625,2.333 0.281,3.323 6.906,5.656 6.625,2.333 0.135,2.917 7.063,2.917 false 3.542,2.792 3.542,0.458 false 3.542,5.656 3.542,3.323 false 0.208,0.198 0.583,0.438 0.375,0.24 12 false *A 0.188,2.99 0.563,3.229 0.375,0.24 12 false *B 0.365,0.531 0.74,0.771 0.375,0.24 12 true *C 0.354,3.385 0.729,3.625 0.375,0.24 12 true *C 3.625,0.5 4,0.74 0.375,0.24 12 true *D 3.625,3.385 4,3.625 0.375,0.24 12 true *D
*A for Type A *A for Type B
*C for RHD *D for LHD




b.

for Rear Side:

i.

Install the No. 8 dust cover with the 3 clips in the order shown in the illustration.

E460100C01
0.125,0.104 7.073,5.729 6.948,5.625 0.292,0.458 6.917,2.792 6.625,2.333 0.281,3.323 6.906,5.656 6.625,2.333 0.135,2.938 7.063,2.938 false 3.542,2.792 3.542,0.458 false 3.542,5.656 3.542,3.323 false 0.208,0.198 0.583,0.438 0.375,0.24 12 false *A 0.188,3 0.563,3.24 0.375,0.24 12 false *B 0.365,0.531 0.74,0.771 0.375,0.24 12 true *C 0.354,3.385 0.729,3.625 0.375,0.24 12 true *C 3.625,0.5 4,0.74 0.375,0.24 12 true *D 3.625,3.385 4,3.625 0.375,0.24 12 true *D
*A for Type A *A for Type B
*C for RHD *D for LHD




Hide 59401 3.INSTALL COOLER CONDENSER COVER SUB-ASSEMBLY

a.

Install the cooler condenser cover sub-assembly with the 8 screws.

E424717C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.688,0.083 4,0.333 0.313,0.25 12 false *B
*A for RHD *B for LHD



Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (for RHD, N04C Series Engine)

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and No. 1 cooler refrigerant discharge hose.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using SST, tighten the nut and connect the No. 1 cooler refrigerant discharge hose.

E424145C02
4.958,0.948 5.271,1.146 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



SST
09617-22010  (09617-24011)

Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




e.

Install the nut.


Hide 88715G 5.CONNECT DISCHARGE TUBE G

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and discharge tube G.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and discharge tube G.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the discharge tube G.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

for RHD, 1HZ:

i.

Using SST, tighten the nut and connect the discharge tube G.

E458135C02
5.469,1.063 5.781,1.26 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the discharge tube G.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



SST
09617-22010  (09617-24011)

Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




ii.

Install the nut.



e.

for LHD, N04C Series Engine:

i.

Using SST, tighten the nut and connect the discharge tube G.

E428604C02
3.594,0.302 3.906,0.5 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the discharge tube G.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



SST
09617-22010  (09617-24011)

Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 88715J 6.CONNECT DISCHARGE TUBE J (for LHD, 1HZ, 2TR-FE)

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and discharge tube J.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and discharge tube J.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the discharge tube J.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using SST, tighten the nut and connect the discharge tube J.

E428604C02
3.594,0.302 3.906,0.5 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the discharge tube J.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



SST
09617-22010  (09617-24011)

Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 88716E 7.CONNECT COOLER REFRIGERANT LIQUID PIPE E

a.

for Type A:

i.

Remove the vinyl tape wrapped around the connection of the liquid pipe sub-assembly and cooler refrigerant liquid pipe E.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the liquid pipe sub-assembly and discharge tube E.



b.

for Type B:

i.

Remove the vinyl tape wrapped around the connection of the cooler refrigerant liquid pipe P and cooler refrigerant liquid pipe E.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe P and discharge tube E.



c.

Install the O-ring to the cooler refrigerant liquid pipe E.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using a union nut wrench 19 mm, tighten the nut and connect the cooler refrigerant liquid pipe E.

E428605C01
0.083,0.094 0.396,0.333 0.313,0.24 12 false *A 0.156,4.021 0.417,4.25 0.26,0.229 12 true *B 3.917,2.208 4.229,2.365 0.313,0.156 10 false *a 4.083,6.708 4.396,6.865 0.313,0.156 10 false *a
*A for RHD *B for LHD
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the cooler refrigerant liquid pipe E.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 11.4 N*m (116 kgf*cm, 8 ft.*lbf)




e.

Install the bolt.


Hide 10.INSPECT FOR REFRIGERANT LEAK