Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE WINDOW GLASS (for Front Passenger Side) › from 2021.01
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356209 FRONT SIDE WINDOW GLASS(for Front Passenger Side) A

WINDOW / GLASS  FRONT SIDE WINDOW GLASS(for Front Passenger Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1.CLEAN FRONT SIDE WINDOW GLASS LH

a.
E268586

Clean the outer edge of the front side front window glass LH with non-residue solvent.

NOTICE:
·

Do not touch the front side window glass LH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new front side window glass LH, clean the front side window glass LH with non-residue solvent.




Hide 62269F 2.INSTALL SIDE WINDOW FRAME FILM (for Slide Glass Type)

NOTICE:

Perform the following procedures when replacing the side window frame film.


HINT:

Remove the double-sided tape remaining on the installation surface of the side window frame film of the front side window glass assembly LH.


a.

Using non-residue solvent, clean the installation surface of the side window frame film of the front side window glass assembly LH.


b.

Remove the peeling paper on a new side window frame film while making sure not to touch the adhesional surface.


c.

Install the 9 pieces of side window frame film at the positions shown in the illustration.

B507062C01
1.573,3.51 1.833,3.51 1.833,3.51 1.896,3.396 true 3.385,3.521 3.646,3.521 3.646,3.521 3.708,3.406 true 4.604,3.25 4.958,3.552 0.354,0.302 10 false a 1.365,3.417 1.688,3.677 0.323,0.26 10 false *a 2.115,3.458 2.458,3.729 0.344,0.271 10 false *b 3.938,3.458 4.292,3.719 0.354,0.26 10 false *b 3.198,3.427 3.531,3.677 0.333,0.25 10 false *a 0.188,0.146 0.552,0.438 0.365,0.292 10 false *c 2.802,3.26 3.156,3.563 0.354,0.302 10 false a
*a Specified Application Position *b Align the lateral center of the front window frame film RH with the center of the hole in the front side window glass assembly LH.
*c Back side - -
V100155

Tape - -


Standard
Area Specified Condition
a 4.6 mm (0.181 in.)


Hide 68142D 3.INSTALL SIDE FRONT WINDOW RUN LH (for Slide Glass Type)

NOTICE:

Perform the following procedures when replacing the side front window run LH.


HINT:

Remove the adhesive remaining on the installation surface of the side front window run LH of the front side window glass assembly LH.


a.

Using non-residue solvent, clean the installation surface of the side front window run LH of the front side window glass assembly LH.


b.
B505399C02
0.104,0.083 0.417,0.281 0.313,0.198 10 false *a
*a Back Side


Apply adhesive to the installation surface of the side front window run LH of the front side window glass assembly LH.

NOTICE:
·

Make sure that the adhesive does not contact any other areas outside of the application area.

·

Clean any protruding adhesive.

·

Apply adhesive to the entire circumference.




c.

Install a new side front window run LH to the front side window glass assembly LH.


Hide 62910L 4.INSTALL SIDE WINDOW LOCK ASSEMBLY (for Slide Glass Type)

HINT:

Use the same procedure for each of the side window lock assemblies.


a.
B471136

Install the side window lock packing.

NOTICE:

If there is extreme damage to the side window lock packing, replace it with a new one.



b.
B471137

Install the side window lock retainer.


c.
B471135

Install the side window lock assembly with 2 screws.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the side window lock packing.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install the side window lock assembly with 2 screws.



Hide 62746G 5.INSTALL QUARTER WINDOW PACKING (for Slide Glass Type)

NOTICE:

Perform the following procedures when replacing the quarter window packing.


HINT:

Clean any adhesive from the installation surface of the quarter window packing on the front side window center frame sub-assembly LH.


a.

Using non-residue solvent, clean the installation surface of the quarter window packing of the front side window center frame sub-assembly LH.


b.
B471150E01
2.375,0.792 2.531,0.99 0.156,0.198 10 false a

Install a new quarter window packing to the front side window center frame sub-assembly LH and keep it in the position shown in the illustration.

Standard
Area Specified Condition
a 3.0 mm (0.118 in.)


c.
B471198

Apply instant adhesive to the fitting surface (dotted line) on the quarter window packing and front side window center frame sub-assembly LH to secure the quarter window packing.

NOTICE:

Make sure that instant adhesive does not contact any other areas outside of the application area.



d.
B505393C01
2.51,0.313 2.75,0.115 2.75,0.115 2.885,0.115 true 1.344,0.385 1.5,0.583 0.156,0.198 10 false c 0.396,1.302 0.552,1.5 0.156,0.198 10 false a 0.875,1.906 1.031,2.104 0.156,0.198 10 false b 2.958,0.052 3.198,0.229 0.24,0.177 10 false *a
*a Seal Area


Prepare an EPT sealer with the dimensions shown in the illustration.

HINT:

A generic EPT sealer can be used.


Standard
Area Specified Condition
a 5.0 mm (0.197 in.)
b 4.0 mm (0.157 in.)
c 30 mm (1.18 in.)


e.

Remove the peeling paper and install the EPT sealer to the center side window frame sub-assembly at the position shown in the illustration.

B505394C01
1.865,1.208 2.302,0.635 2.302,0.635 2.458,0.635 false 3.26,2.208 4.281,2.208 false 2.51,0.552 2.823,0.75 0.313,0.198 10 false *b 3.042,2.135 3.302,2.323 0.26,0.188 10 false *a 2.74,1.813 2.927,2 0.188,0.188 10 false A 6.688,2.104 6.948,2.292 0.26,0.188 10 false *a 5.781,0.792 6.042,0.979 0.26,0.188 10 false *c
*a Application Reference Line *b Specified Application Position
*c View A - -



Hide 62777U 6.INSTALL SIDE WINDOW CENTER SASH CAP (for Slide Glass Type)

NOTICE:

Perform the following procedures when replacing the side window center sash cap.


a.
B519652C01
1,1.948 1.313,2.146 0.313,0.198 10 false *a
*a Vehicle Front


Install a new side window center sash cap to the front side window glass assembly LH at the position shown in the illustration.


Hide 62211F 7.INSTALL REAR SIDE WINDOW GLASS LH (for Slide Glass Type)

NOTICE:
·

Do not damage the front side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the rear side window glass LH.



a.
B471191

Widen top and bottom of the window frame using your hands and install the rear side window glass LH.


b.
B471213

Install the center side window frame sub-assembly.


c.

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front side front window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.



Hide 62121 8.INSTALL FRONT SIDE FRONT WINDOW GLASS LH (for Slide Glass Type)

NOTICE:
·

Do not damage the front side front window glass LH.

·

Do not damage the window frame.

·

Do not damage the front side front window glass LH.



a.
B471190

Widen top and bottom of the window frame using your hands and install the front side front window glass LH.


b.
B471189

Install the screw:

i.

Before applying adhesive, clean off any old adhesive from the threaded portion.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the front side front window glass LH.


iii.

Apply adhesive to the threaded portion.


iv.

Install the 2 screws.


v.
B471199E01
1.229,0.208 1.385,0.406 0.156,0.198 10 false a 2.031,0.208 2.188,0.406 0.156,0.198 10 false a 2.906,1.031 3.063,1.229 0.156,0.198 10 false b

Apply sealant (water proof) to the head of the screw in the area shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 12.2 mm (0.480 in.)




Hide 62391B 9.INSTALL NO. 1 FRONT SIDE WINDOW STOPPER LH (for Slide Glass Type)

a.
B471197

Install the No. 1 front side window stopper LH.

i.

Before applying adhesive, clean off any old adhesive from the threaded portion of the screw.


ii.

Using non-residue solvent, clean and remove any oil, water or foreign matter from the threaded portion of the No. 1 front side window stopper LH.


iii.

Apply adhesive to the threaded portion of the screw.


iv.

Install a new No. 1 front side window stopper LH with the 2 screws.



Hide 62763N 10.INSTALL SIDE WINDOW FRAME RETAINER

a.

Using non-residue solvent, clean the side window frame retainer installation surface of the front side window glass LH.


b.

Install the primer to the side window frame retainer installation surface of the front side window glass LH.


c.

Remove the peeling paper from a new side window frame retainer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

for Slide Glass Type:

i.

Install the 3 side window frame retainers to the front side window glass LH as shown in the illustration.

B471195C01
4.583,1.583 4.813,1.396 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.26,0.448 1.417,0.625 0.156,0.177 10 false a 1.271,0.688 1.427,0.865 0.156,0.177 10 false b 1.271,0.906 1.427,1.083 0.156,0.177 10 false c 1.823,1.115 1.979,1.292 0.156,0.177 10 false A 1.823,1.313 1.958,1.49 0.135,0.177 10 true A 4.302,0.844 4.729,1.021 0.427,0.177 10 false A-A 4.354,1.552 4.594,1.74 0.24,0.188 10 false *1
*1 Side Window Frame Retainer - -
*a Back side - -


Standard:
Area Specified Condition
a 383.5 mm (15.1 in.)
b 533.4 mm (21.0 in.)
c 683.1 mm (26.9 in.)




e.

for Fixed Glass Type:

i.

Install the 3 side window frame retainers to the front side window glass LH as shown in the illustration.

E459221C01
5.302,1.479 5.031,1.771 false 2.625,0.219 2.177,0.448 true 1.51,1.292 1.635,1.479 0.125,0.188 10 true A 1.51,1.115 1.625,1.281 0.115,0.167 10 true A 4.917,0.771 5.375,0.969 0.458,0.198 10 false A-A 2.646,0.125 2.958,0.323 0.313,0.198 10 false *1 4.875,1.729 5.188,1.927 0.313,0.198 10 false *1 4.865,1.219 5.021,1.417 0.156,0.198 10 false a
*1 Side Window Frame Retainer - -
*a Back side - -


Standard:
Area Specified Condition
a 1.6 to 3.0 mm (0.0630 to 0.118 in.)




Hide 62375B 11.INSTALL NO. 1 SIDE WINDOW CLIP

a.

Using non-residue solvent, clean the No. 1 side window clip installation surface of the front side window glass LH.


b.

Install the primer to the No. 1 side window clip installation surface of the front side window glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new No. 1 side window clip.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

for Slide Glass Type:

i.

Install the 3 No. 1 side window clips to the front side window glass LH as shown in the illustration.

B471196C01
0.896,1.021 1.219,0.813 true 0.896,1.479 1.135,1.677 true 0.885,2.323 1.208,2.115 true 0.906,2.781 1.146,2.979 true 1.271,0.698 1.521,0.865 0.25,0.167 10 false *d 1.177,1.656 1.427,1.823 0.25,0.167 10 false *d 1.26,2.021 1.51,2.188 0.25,0.167 10 false *d 1.188,2.927 1.438,3.094 0.25,0.167 10 false *d 0.167,0.125 0.417,0.292 0.25,0.167 10 false *a 0.583,1.188 0.792,1.354 0.208,0.167 10 false *b 0.583,2.479 0.792,2.646 0.208,0.167 10 false *c 5.333,3.573 5.49,3.729 0.156,0.156 10 false a
*a Back Side *b Long Clip
*c Short Clip *d Ceramic Notch


Standard:
Area Specified Condition
a 117.1 mm (4.61 in.)




e.

for Fixed Glass Type:

i.

Install the 3 No. 1 side window clips to the front side window glass LH as shown in the illustration.

E459222C01
0.688,1.708 1.125,1.969 true 0.667,3.01 1.104,3.271 true 6.115,2.615 6.25,3.188 true 0.094,0.042 0.406,0.24 0.313,0.198 10 false *a 1.083,0.958 1.24,1.156 0.156,0.198 10 false a 1.094,2.302 1.25,2.5 0.156,0.198 10 false a 5.583,2.292 5.74,2.49 0.156,0.198 10 false b 1.156,1.906 1.469,2.104 0.313,0.198 10 false *b 1.135,3.208 1.448,3.406 0.313,0.198 10 false *b 6.198,3.208 6.51,3.406 0.313,0.198 10 false *b
*a Back Side *b Positioning Line


Standard:
Area Specified Condition
a 0 to 0.5 mm (0 to 0.0197 in.)
b 0 to 0.5 mm (0 to 0.0197 in.)