Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM M

N04C-VJ ENGINE CONTROL  ECD SYSTEM  REGISTRATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When an injector assembly is replaced, the injector's compensation code must be input into the ECM.

·

When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.



PROCEDURE

Hide 1.INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
·

Injector compensation codes are printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

Although some injectors are marked with a 32-digit alphanumeric value, only the first 30-digits must to be input.



a.
A262683C04
0.094,0.052 1.323,0.25 1.229,0.198 10 false *a 2.75,0.521 3.385,0.823 0.635,0.302 10 false *b
*a Example
*b Injector Compensation Code


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.

NOTICE:

Do not start the engine.


HINT:

The injector compensation code is imprinted on the head portion of each injector assembly



d.
A321636

Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.


e.

Press "Next".


f.
A321637

Press "Next" again to proceed.


g.
A321638

Select "Set Compensation Code".


h.

Press "Next".


i.
A321639

Select the number of the cylinder corresponding to the injector compensation code that you want to register.


j.

Press "Next".


k.
A321640

Register the compensation code.

i.

Press "Input".


ii.

Manually input the cylinder's compensation code using the keyboard on the tester screen. The code is imprinted on the injector's head portion.

NOTICE:

Although some injectors are marked with a 32-digit alphanumeric value, only the first 30-digits must to be input.


HINT:

Each injector compensation code is unique.

The correct compensation code must be input into each cylinder selected on the tester.



iii.

Confirm that the compensation code is correct for the selected cylinder, and then press "OK".



l.
A321642

Check that the compensation code displayed on the screen is correct, by comparing it with the compensation code on the head portion of the injector.

NOTICE:

If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If a wrong compensation code was input, return to the "Input Value" screen by pressing "Input".

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.




m.

Press "Next" to set the compensation code to the ECM.

HINT:
·

If the setting process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure.

Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.




n.
A321643

To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".


o.

Turn the ignition switch off and then turn the tester off.


p.

Wait for at least 30 seconds.


q.

Turn the ignition switch to ON and then turn the GTS on.


r.

Clear DTC P062F stored in the ECM using the tester (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).


Hide 2. VIEW ENGINE HISTORY USING ENGINE HISTORY UTILITY

This procedure can be used to display engine-related data that was stored in the ECM on the GTS (Max Engine Speed, Max Coolant Temperature, Max Fuel Temperature, Max Exhaust Temperature, Max Vehicle Speed, Max Fuel Injection Volume, Max Rail Pressure, Max Boost Pressure, Min Boost Pressure, Engine Overrun Count and Engine Overheat Count).

This engine-related data records maximum values and can be used when engine over revving or overheating is suspected to have occurred.

A258817E01
3.27,0.99 3.593,1.164 0.323,0.175 10 Next 3.27,1.989 3.593,2.164 0.323,0.175 10 Next 3.27,3.343 3.593,3.518 0.323,0.175 10 Next 6.011,3.923 6.344,4.116 0.332,0.193 10 End 4.382,0.733 4.732,0.898 0.351,0.166 10 Exit 4.382,1.732 4.732,1.898 0.351,0.166 10 Exit 4.382,2.942 4.732,3.107 0.351,0.166 10 Exit 4.382,4.17 4.732,4.336 0.351,0.166 10 Exit 1.323,1.653 1.664,1.837 0.341,0.184 10 Back 1.738,2.89 2.08,3.074 0.341,0.184 10 Back 2.952,0.504 3.386,0.679 0.434,0.175 10 Start 2.78,2.9 3.589,3.075 0.809,0.175 10 View History 2.366,1.496 4.009,1.68 1.642,0.184 10 Confirmation of conditions 2.408,2.505 3.898,2.682 1.49,0.177 10 Selection of procedure 1.154,3.551 1.503,3.698 0.349,0.148 10 Error 2.492,3.885 3.933,4.083 1.441,0.198 10 Confirmation of history

HINT:

A read error may occur when there is a problem with the ECM or wire harness, or when there is a problem with the DLC3 connection. In this situation, inspect the wire harness and DLC3 connection. If the wire harness and DLC3 connection are normal, the ECM may be malfunctioning.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to the ON position.


c.

Turn the tester on.

NOTICE:

Do not start the engine.



d.

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Engine History Utility.


e.

Press "Next".


f.

Once the condition confirmation screen appears, press "Next".


g.

Select the option to view the engine history from the selection screen, and then press "Next".


h.

Confirm the engine history and press "Exit" when finished.


Hide 3. SAVE ENGINE HISTORY USING ENGINE HISTORY UTILITY

This procedure is performed before replacing the ECM.

The engine-related data from the old ECM is saved in the GTS so that it can be transferred to the new ECM after replacement (Max Engine Speed, Max Coolant Temperature, Max Fuel Temperature, Max Exhaust Temperature, Max Vehicle Speed, Max Fuel Injection Volume, Max Rail Pressure, Max Boost Pressure, Min Boost Pressure, Engine Overrun Count and Engine Overheat Count).

A258818E03
3.375,0.583 4.156,0.823 0.781,0.24 10 false Next 3.375,1.583 4.531,1.927 1.156,0.344 10 false Next 2.708,2.938 3.729,3.177 1.021,0.24 10 false Next 2.5,5.271 2.833,5.469 0.333,0.198 10 false End 4.479,0.323 4.833,0.49 0.354,0.167 10 false Exit 4.479,1.323 4.833,1.49 0.354,0.167 10 false Exit 4.479,2.542 4.833,2.708 0.354,0.167 10 false Exit 2.719,4.719 3.073,4.885 0.354,0.167 10 false Exit 1.427,1.25 2.146,1.438 0.719,0.188 10 false Back 1.833,2.49 2.427,2.708 0.594,0.219 10 false Back 3.052,0.104 3.49,0.281 0.438,0.177 10 false Start 4.729,3.688 5.406,3.865 0.677,0.177 10 false Overwrite 5.594,3.365 6.448,3.542 0.854,0.177 10 false Cancel 2.813,2.458 4.094,2.76 1.281,0.302 10 false Save History 2.479,1.083 4.146,1.25 1.667,0.167 10 false Confirmation of conditions 2.49,2.104 3.948,2.26 1.458,0.156 10 false Selection of procedure 2.667,3.406 4.271,3.677 1.604,0.271 10 false Saved data exists 2.667,3.854 4.406,4.042 1.74,0.188 10 false Saved data does not exist 3.896,3.146 5.333,3.313 1.438,0.167 10 false Overwrite confirmation 1.25,3.563 1.646,3.719 0.396,0.156 10 false Error 1.979,4.208 3.313,4.354 1.333,0.146 10 false History data is saved

HINT:

A read error may occur when there is a problem with the ECM or wire harness, or when there is a problem with the DLC3 connection. In this situation, inspect the wire harness and DLC3 connection. If the wire harness and DLC3 connection are normal, the ECM may be malfunctioning.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to the ON position.


c.

Turn the tester on.

NOTICE:

Do not start the engine.



d.

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Engine History Utility.


e.

Once the condition confirmation screen appears, press "Next".


f.

Select the option to save the engine history from the selection screen, and then press "Next".


g.

If engine history data already exists in the GTS, a data overwrite confirmation message will be displayed. In this case, press "Overwrite".

HINT:

If engine history data does not already exist, the data overwrite confirmation message is not displayed.



h.

Confirm the save date and press "Exit".


Hide 4. WRITE ENGINE HISTORY USING ENGINE HISTORY UTILITY

This procedure is used to write the engine-related data saved in the GTS with the engine history save utility to the new ECM (Max Engine Speed, Max Coolant Temperature, Max Fuel Temperature, Max Exhaust Temperature, Max Vehicle Speed, Max Fuel Injection Volume, Max Rail Pressure, Max Boost Pressure, Min Boost Pressure, Engine Overrun Count and Engine Overheat Count).

A258816E03
3.104,0.583 3.427,0.76 0.323,0.177 10 false Next 3.104,1.583 3.427,1.76 0.323,0.177 10 false Next 3.083,2.948 3.406,3.125 0.323,0.177 10 false Next 5.844,6.292 6.177,6.49 0.333,0.198 10 false End 4.219,0.323 4.573,0.49 0.354,0.167 10 false Exit 4.219,1.323 4.573,1.49 0.354,0.167 10 false Exit 4.219,2.542 4.573,2.708 0.354,0.167 10 false Exit 3.135,4.75 4.073,5.125 0.938,0.375 10 false Yes 1.156,1.25 1.5,1.438 0.344,0.188 10 false Back 1.573,2.49 1.917,2.677 0.344,0.188 10 false Back 2.792,0.104 3.229,0.281 0.438,0.177 10 false Start 5.458,3.573 5.927,3.917 0.469,0.344 10 false OK 2.604,2.51 3.458,2.698 0.854,0.188 10 false Write History 4.219,4.458 4.5,4.625 0.281,0.167 10 false No 4.219,5.51 4.573,5.677 0.354,0.167 10 false Exit 3.104,5.75 3.438,5.906 0.333,0.156 10 false View 2.229,1.083 3.917,1.26 1.688,0.177 10 false Confirmation of conditions 2.25,2.104 3.698,2.281 1.448,0.177 10 false Selection of procedure 3.979,3.125 5.406,3.292 1.427,0.167 10 false Saved data abnormal 3.958,3.427 5.375,3.75 1.417,0.323 10 false Saved data does not exist 2.688,4.198 3.396,4.375 0.708,0.177 10 false Write data 0.969,4.948 1.323,5.115 0.354,0.167 10 false Error 2.042,5.25 4.104,5.417 2.063,0.167 10 false Writing of history data complete 2.177,6.25 3.979,6.406 1.802,0.156 10 false Confirmation of history data

HINT:

A write error may occur when there is a problem with the ECM or wire harness, or when there is a problem with the DLC3 connection. In this situation, inspect the wire harness and DLC3 connection. If the wire harness and DLC3 connection are normal, the ECM may be malfunctioning.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to the ON position.


c.

Turn the tester on.

NOTICE:

Do not start the engine.



d.

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Engine History Utility.


e.

Once the condition confirmation screen appears, press "Next".


f.

Select the option to write the engine history from the selection screen, and then press "Next".


g.

If the engine history data does not exist or the engine history data is abnormal, a message will appear. In this case, resave the engine history data.


h.

Confirm the save date and press "Yes".


i.

Once a message appears indicating that the write operation has been completed, press "View" to confirm the engine history data.


Hide 5. CLEAR ENGINE HISTORY DATA USING ENGINE HISTORY UTILITY

This procedure is used to clear the engine-related data saved in the ECM (Max Engine Speed, Max Coolant Temperature, Max Fuel Temperature, Max Exhaust Temperature, Max Vehicle Speed, Max Fuel Injection Volume, Max Rail Pressure, Max Boost Pressure, Min Boost Pressure, Engine Overrun Count and Engine Overheat Count).

A258819E04
3.104,0.583 3.427,0.76 0.323,0.177 10 false Next 3.104,1.635 3.427,1.813 0.323,0.177 10 false Next 3.083,2.948 3.406,3.125 0.323,0.177 10 false Next 5.844,6.292 6.177,6.49 0.333,0.198 10 false End 4.219,0.365 4.573,0.531 0.354,0.167 10 false Exit 4.219,1.354 4.573,1.521 0.354,0.167 10 false Exit 4.219,2.542 4.573,2.708 0.354,0.167 10 false Exit 1.156,1.25 1.5,1.438 0.344,0.188 10 false Back 1.573,2.51 1.917,2.698 0.344,0.188 10 false Back 2.792,0.135 3.229,0.313 0.438,0.177 10 false Start 2.604,2.51 3.458,2.698 0.854,0.188 10 false Clear History 4.219,5.51 4.573,5.677 0.354,0.167 10 false Exit 3.104,5.75 3.438,5.906 0.333,0.156 10 false View 2.26,3.906 3.854,4.104 1.594,0.198 10 false Engine History Data 3.125,4.688 3.448,4.865 0.323,0.177 10 false Next 4.208,4.125 4.563,4.292 0.354,0.167 10 false Exit 2.208,1.156 3.875,1.354 1.667,0.198 10 false Confirmation of conditions 2.25,2.135 3.708,2.333 1.458,0.198 10 false Selection of procedure 2.167,3.521 3.75,3.677 1.583,0.156 10 false Selection of item to clear 0.979,4.948 1.375,5.125 0.396,0.177 10 false Error 1.979,5.229 4.167,5.417 2.188,0.188 10 false Clearing of history data complete 2.104,6.229 3.969,6.417 1.865,0.188 10 false Confirmation of history data 2.052,4.208 4.177,4.531 2.125,0.323 10 false PM Accumulation History Data

·

When any of the following parts are replaced, the engine history data must be cleared.

-

Engine assembly

-

Turbocharger sub-assembly

-

Injection or supply pump assembly

-

Injection or supply pump assembly (fuel temperature sensor)

-

Injection or supply pump assembly (suction control valve)

-

Injector assembly

-

Engine coolant temperature sensor

-

Common rail assembly (fuel pressure sensor)

-

Manifold absolute pressure


·

When the following part is replaced, the PM accumulation history data must be initialized.

-

Monolithic Converter Assembly



HINT:

A reset error may occur when there is a problem with the ECM or wire harness, or when there is a problem with the DLC3 connection. In this situation, inspect the wire harness and DLC3 connection. If the wire harness and DLC3 connection are normal, the ECM may be malfunctioning.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to the ON position.


c.

Turn the tester on.

NOTICE:

Do not start the engine.



d.

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Engine History Utility.


e.

Once the condition confirmation screen appears, press "Next".


f.

Select the option to clear the engine history from the selection screen, and then press "Next".


g.

Select the item to clear from the engine history reset selection screen and press "Next".


h.

Once a message appears indicating that the data has been cleared, press "View" to confirm the engine history data.