DESCRIPTION
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an GTS, 5 separate sets of freeze frame data can be checked.
3 data sets before the DTC was stored.
1 data set when the DTC was stored.
1 data set after the DTC was stored.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
LIST OF FREEZE FRAME DATA
| Tester Display |
|---|
| Vehicle Speed |
| Target Idle Engine Speed |
| Engine Speed |
| Calculate Load |
| MAF |
| Atmosphere Pressure |
| MAP |
| Coolant Temp |
| Intake Air |
| Intake Air Temp (Turbo) |
| NOx Density B1S1 |
| NOx Density B1S1 Supported |
| Engine Run Time |
| Initial Engine Coolant Temp |
| Initial Intake Air Temp |
| Battery Voltage |
| Pre Glow |
| After Glow |
| Accel Position |
| Accel Sens. No.1 Volt % |
| Accel Sens. No.2 Volt % |
| Target Throttle Position |
| Actual Throttle Position |
| Diesel Throttle Learn Status |
| Throttle Sensor Volt % |
| Throttle Motor DUTY |
| Injection Volume |
| Inj. FB Vol. for Idle |
| Inj Vol Feedback Learning |
| Injection Feedback Val #1 |
| Injection Feedback Val #2 |
| Injection Feedback Val #3 |
| Injection Feedback Val #4 |
| Pilot 1 Injection Period |
| Pilot 2 Injection Period |
| Main Injection Period |
| After Injection Period |
| Pilot 1 Injection Timing |
| Pilot 2 Injection Timing |
| Main Injection Timing |
| After Injection Timing |
| Injector Memory Error |
| Target Common Rail Pressure |
| Fuel Press |
| Common Rail Pressure 2 |
| Fuel Temperature |
| Fuel Return Temp |
| Target Pump SCV Current |
| Pump SCV Learning Value |
| AF Lambda B1S1 |
| AFS Voltage B1S1 |
| Target EGR Position |
| EGR Initial Step Position |
| Actual EGR Valve Pos. |
| EGR Close Lrn. Val. |
| EGR Operation Prohibit |
| Target Booster Pressure |
| VN Turbo Command |
| Actual VN Position |
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
| Exhaust Temperature B1S4 |
| DPF Differential Pressure |
| Catalyst Differential Press |
| Exhaust Fuel Addition FB |
| DPF PM Block |
| Add. INJ Flow Excessive |
| DPF Overtemperature |
| PM Accumulation Ratio |
| Catalyst Regeneration Switch |
| Exhaust Brake Switch |
| Starter Signal |
| IG SW |
| Neutral Position SW Signal |
| Clutch Switch |
| Reverse Switch |
| Stop Light Switch |
| A/C Signal |
| Engine Stop SW |
| # Codes(Include History) |
| Time after DTC Cleared |
| Distance from DTC Cleared |
| Warmup Cycle Cleared DTC |
| TC and TE1 |
| Engine Start Time |
| Engine Speed (Starter Off) |
| Starter Count |
| Run Dist of Previous Trip |
| Glow Request Lighting Time |
| IG-ON Time |
| MAF Low |
| Boost Pressure Low |
| Common Rail Pressure Low |
| Engine Coolant Temp High |
| MAF/Estimate MAF Ratio |
| Engine Warm Up Switch |
| ACT VSV |