Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM U

N04C-VJ ENGINE CONTROL  ECD SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE CHART


If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC No. Detection Item Fail-safe Operation Fail-safe Deactivation Condition
P0006
P0007
Fuel Shutoff Valve "A" Control Circuit Low
Fuel Shutoff Valve "A" Control Circuit High
·

NOx reduction control is prohibited

·

Fuel addition is prohibited


Returns to normal conditions
P0045 Turbocharger / Supercharger Boost Control Solenoid Circuit / Open
·

Engine output limiting control is performed

·

VN turbo position is limited

·

NOx reduction control is prohibited

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped


IG OFF
P0087 Fuel Rail / System Pressure - Too Low
·

Engine output limiting control is performed

·

NOx reduction control is prohibited

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

Target rail pressure is assigned as rail pressure

·

PM regeneration control is stopped


Ignition switch off → ON or STA ON
P0088 Fuel Rail / System Pressure - Too High
·

Fuel injection is stopped at engine speed of 1800 rpm or higher

·

Target rail pressure is fixed at 35000 kPa

·

Engine output limiting control is performed

·

NOx reduction control is prohibited

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped


Ignition switch off → ON or STA ON
P0093 Fuel System Leak Detected - Large Leak
·

Engine output limiting control is performed

·

NOx reduction control is prohibited

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped


Ignition switch off → ON or STA ON
P0095
P0097
P0098
Intake Air Temperature Sensor 2 Circuit
Intake Air Temperature Sensor 2 Circuit Low
Intake Air Temperature Sensor 2 Circuit High
Post-turbo intake air temperature is fixed at 90°C Sensor output value returns to normal condition
P0102
P0103
Mass Air Flow Circuit Low
Mass Air Flow Circuit High
·

NOx reduction control is prohibited

·

EGR control is limited (intake air volume FB is stopped)

·

PM regeneration control is stopped


Sensor output value returns to normal condition
P0107
P0108
Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
Manifold Absolute Pressure / Barometric Pressure Circuit High Input
·

Engine output limiting control is performed

·

Intake manifold pressure is fixed at 101.3 kPa


Sensor output value returns to normal condition
P0112
P0113
Intake Air Temperature Circuit Low Input
Intake Air Temperature Circuit High Input
·

Post-turbo intake air temperature is fixed at 60°C

·

Idle up speed is fixed at a certain value during PM regeneration


Sensor output value returns to normal condition
P0115
P0117
P0118
Engine Coolant Temperature Circuit
Engine Coolant Temperature Circuit Low Input
Engine Coolant Temperature Circuit High Input
·

Fuel temperature is less than 15°C: Fuel sensor value is assigned

·

Fuel temperature is 15°C or higher: Fixed at 80°C


Sensor output value returns to normal condition
P0122
P0123
Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped


IG OFF
P0130 Oxygen Sensor Circuit (Bank 1 Sensor 1) Exhaust fuel addition injector assembly malfunction determination is stopped according to the A/F value Sensor output value returns to normal condition
P0168 Fuel Temperature Too High
·

Maximum injection volume is corrected

·

Maximum rail pressure is corrected


Returns to normal conditions
P0180
P0182
P0183
Fuel Temperature Sensor "A" Circuit
Fuel Temperature Sensor "A" Circuit Low Input
Fuel Temperature Sensor "A" Circuit High Input
·

Engine output limiting control is performed

·

Fuel temperature is fixed at 40°C

·

High fuel temperature compensation control is limited


Sensor output value returns to normal condition
P0190
P0192
P0193
Fuel Rail Pressure Sensor Circuit
Fuel Rail Pressure Sensor Circuit Low Input
Fuel Rail Pressure Sensor Circuit High Input
·

Engine output limiting control is performed

·

For malfunction in 1 system only, controlled at normal sensor value

·

For malfunctions in 2 systems only, target rail pressure is assigned as rail pressure

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened


Sensor output value returns to normal condition
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

Target rail pressure is assigned as rail pressure


Sensor output value returns to normal condition
P0201
P0202
P0203
P0204
Injector Circuit / Open - (Cylinder 1)
Injector Circuit / Open - (Cylinder 2)
Injector Circuit / Open - (Cylinder 3)
Injector Circuit / Open - (Cylinder 4)
·

For malfunction in 1 cylinder only, engine output limiting control is performed

·

For malfunctions in 2 cylinders or more, engine stalls

-

PM regeneration control is stopped

-

NOx reduction control is prohibited



IG OFF
P0234 Turbocharger / Supercharger Overboost Condition
·

Engine output limiting control is performed

·

VN turbo position is limited

·

PM regeneration control is stopped

·

NOx reduction control is prohibited

·

Target EGR position is fully opened


IG OFF
P0299 Turbocharger / Supercharger Underboost VN turbo position is limited IG OFF
P0335
P0339
Crankshaft Position Sensor "A" Circuit
Crankshaft Position Sensor "A" Circuit Intermittent
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited

·

Injection pump is stopped


NE pulse input present
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened


IG OFF
P0545
P0546
Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)
Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)
·

Exhaust temperature is fixed at 200°C

·

Post injection is limited


Sensor output value returns to normal condition
P0627 Fuel Pump Control Circuit / Open
·

Suction control valve power is prohibited

·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


Ignition switch off → ON or STA ON
P062D No. 1 Fuel Injector Driver Circuit Performance
·

PM regeneration control is stopped

·

NOx reduction control is prohibited


IG OFF
P1229 Fuel Pump System
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

Target diesel throttle position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


Ignition switch off → ON or STA ON
P1251 Turbocharger / Supercharger Overboost Condition (Too High)
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

VN turbo position is limited

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


IG OFF
P1427
P1428
Differential Pressure Sensor Circuit Low
Differential Pressure Sensor Circuit High
·

Catalyst differential pressure is fixed at 0 kPa

·

Detection of catalyst filter blockage due to differential pressure is stopped


Sensor output value returns to normal condition
P1458
P1459
EGR Actuator Minor Malfunction
EGR Actuator Major Malfunction
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


Returns to normal conditions
P1530 Engine Emergency Halt Switch Emergency halt control is prohibited Returns to normal conditions
P1674 Solenoid for Exhaust Brake Circuit Malfunction Exhaust brake operation is stopped Returns to normal conditions
P200C Particulate Filter Over Temperature Bank 1
·

Engine output limiting control is performed

·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


IG OFF
P2032
P2033
Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
·

Exhaust temperature is fixed at 200°C

·

NOx reduction control is prohibited


Sensor output value returns to normal condition
P20CD
P20CE
Exhaust Aftertreatment Fuel Injector "A" Control Circuit Low
Exhaust Aftertreatment Fuel Injector "A" Control Circuit High
·

NOx reduction control is prohibited

·

Fuel addition is prohibited


Returns to normal conditions
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open
·

NOx reduction control is prohibited

·

Fuel addition is prohibited


Learning value in ECM is cleared due to removal of ECD fuse
P2120
P2122
P2123
P2125
P2127
P2128
P2138
Throttle / Pedal Position Sensor / Switch "D" Circuit
Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
Throttle / Pedal Position Sensor / Switch "E" Circuit
Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
Throttle / Pedal Position Sensor / Switch "D"/"E" Voltage Correlation
·

Engine output limiting control is performed

·

For malfunctions in both accel sensor 1 and 2, PM regeneration control is stopped


Sensor output value returns to normal condition
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance Engine output limiting control is performed Sensor output value returns to normal condition
P2200 NOx Sensor Circuit Bank 1 Sensor 1 Correction of the NOx reduction addition amount according to the NOx sensor value is stopped Sensor output value returns to normal condition
P2205 NOx Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) Exhaust fuel addition injector assembly malfunction determination is stopped according to the A/F value Sensor output value returns to normal condition
P2226
P2228
P2229
Barometric Pressure Circuit
Barometric Pressure Circuit Low Input
Barometric Pressure Circuit High Input
Atmospheric pressure is fixed at 101.3 kPa Sensor output value returns to normal condition
P242C
P242D
Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3
·

Exhaust temperature is fixed at 200°C

·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


Sensor output value returns to normal condition
P244A
P244B
Diesel Particulate Filter Differential Pressure Too Low
Diesel Particulate Filter Differential Pressure Too High
·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


PM accumulation volume history data is initialized
P244D Exhaust Temperature Too High for Particulate Filter Regeneration bank1
·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


IG OFF
P2458 Diesel Particulate Filter Regeneration Duration
·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


IG OFF
P2463 Particulate Filter Restriction - Soot Accumulation
·

Target EGR position is fully opened

·

PM regeneration control is stopped

·

NOx reduction control is prohibited


PM accumulation volume history data is initialized
P2470
P2471
Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 4
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 4
Exhaust temperature is fixed at 200°C Sensor output value returns to normal condition
P24A2 Excessive Amount of Fuel Added During DPF Regeneration
·

PM regeneration control is stopped

·

Target EGR position is fully opened


IG OFF