Home › Vehicle Interior › AIR CONDITIONING › CONDENSER › from 2021.01
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0457158 CONDENSER A

AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88450 1.INSTALL CONDENSER ASSEMBLY WITH RECEIVER

a.

Install the condenser assembly with receiver with the 6 bolts.

NOTICE:

Installing the condenser assembly with receiver to the vehicle must be performed by multiple people.


i.

for Front Side:

E424720C01
0.083,0.083 0.458,0.323 0.375,0.24 12 false *A 3.708,0.094 4.083,0.333 0.375,0.24 12 false *B
*A for RHD *B for LHD



ii.

for Rear Side:

E424721C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.75,0.094 4.083,0.333 0.333,0.24 12 false *B
*A for RHD *B for LHD




b.

Connect the 2 connectors.

E424716C01
0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.688,0.083 4,0.333 0.313,0.25 12 false *B
*A for RHD *B for LHD



Hide 88415L 2.INSTALL NO. 8 DUST COVER

a.

for Front Side:

i.

Install the No. 8 dust cover with the 3 clips in the order shown in the illustration.

E458130C01
0.104,0.083 0.417,0.333 0.313,0.25 12 false *A 3.688,0.094 4,0.333 0.313,0.24 12 false *B
*A for RHD *B for LHD




b.

for Rear Side:

i.

Install the No. 8 dust cover with the 3 clips in the order shown in the illustration.

E458131C01
0.083,0.094 0.458,0.333 0.375,0.24 12 false *A 3.708,0.094 4.083,0.333 0.375,0.24 12 false *B
*A for RHD *B for LHD




Hide 59401 3.INSTALL COOLER CONDENSER COVER SUB-ASSEMBLY

a.

Install the cooler condenser cover sub-assembly with the 8 screws.

E424717C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.688,0.083 4,0.333 0.313,0.25 12 false *B
*A for RHD *B for LHD



Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (for RHD, N04C Series Engine)

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and No. 1 cooler refrigerant discharge hose.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using SST, tighten the nut and connect the No. 1 cooler refrigerant discharge hose.

E424145C02
4.958,0.948 5.271,1.146 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


SST
09617-22010  (09617-24011)

NOTICE:
·

Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




e.

Install the nut.


Hide 88715G 5.CONNECT DISCHARGE TUBE G

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and discharge tube G.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and discharge tube G.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the discharge tube G.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

for RHD, 1HZ:

i.

Using SST, tighten the nut and connect the discharge tube G.

E458135C02
5.469,1.063 5.781,1.26 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


SST
09617-22010  (09617-24011)

NOTICE:
·

Do not apply excessive force to the discharge tube G.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




ii.

Install the nut.



e.

for LHD, N04C Series Engine:

i.

Using SST, tighten the nut and connect the discharge tube G.

E428604C02
3.594,0.302 3.906,0.5 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


SST
09617-22010  (09617-24011)

NOTICE:
·

Do not apply excessive force to the discharge tube G.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 88715J 6.CONNECT DISCHARGE TUBE J (for LHD, 1HZ, 2TR-FE)

a.

Remove the vinyl tape wrapped around the connection of the discharge tube K and discharge tube J.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge tube K and discharge tube J.

Compressor Oil:

ND-OIL 8 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 8 or equivalent. If any compressor oil other than ND-OIL 8 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the O-ring to the discharge tube J.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using SST, tighten the nut and connect the discharge tube J.

E428604C02
3.594,0.302 3.906,0.5 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


SST
09617-22010  (09617-24011)

NOTICE:
·

Do not apply excessive force to the discharge tube J.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52.5 mm (2.07 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 88716E 7.CONNECT COOLER REFRIGERANT LIQUID PIPE E

a.

Remove the vinyl tape wrapped around the connection of the cooler refrigerant liquid pipe P and cooler refrigerant liquid pipe E.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe P and discharge tube E.


c.

Install the O-ring to the cooler refrigerant liquid pipe E.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from foreign matter.



d.

Using a union nut wrench 19 mm, tighten the nut and connect the cooler refrigerant liquid pipe E.

E428605C01
0.083,0.094 0.396,0.333 0.313,0.24 12 false *A 0.156,4.021 0.417,4.25 0.26,0.229 12 true *B 3.917,2.208 4.229,2.365 0.313,0.156 10 false *a 4.083,6.708 4.396,6.865 0.313,0.156 10 false *a
*A for RHD *B for LHD
*a Torque Wrench Fulcrum Length - -


NOTICE:
·

Do not apply excessive force to the cooler refrigerant liquid pipe E.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Torque:
Specified tightening torque : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 11.4 N*m (116 kgf*cm, 8 ft.*lbf)




e.

Install the bolt.


Hide 10.INSPECT FOR REFRIGERANT LEAK