Home › Engine / Hybrid System › N04C-VJ (CHARGING) › GENERATOR › from 2021.01
RM2850E _51 Engine / Hybrid System _096889 N04C-VJ CHARGING _0459685 GENERATOR A

N04C-VJ CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A401288E01
1.563,1.208 0.948,0.542 0.948,0.542 1.698,0.917 true 0.646,0.406 1.104,0.604 0.458,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60011  (09951-00470)
09950-70010  (09951-07100)


Hide 27312 2.INSTALL RETAINER PLATE

a.
A401286C01
2.094,1.229 2.698,1.479 true 0.875,0.802 1.479,1.052 true 0.698,0.688 1.01,0.885 0.313,0.198 10 false *a 2.76,1.406 3.073,1.604 0.313,0.198 10 false *a
*a Claw


Align the claws of the bearing retainer with the grooves inside the drive end frame.


b.

Install the retainer plate with the 4 screws.

Torque:

2.3 N*m (23 kgf*cm, 20 in.*lbf)



Hide 27330 3.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A401290

Install the generator rotor assembly to the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27384 4.INSTALL WASHER

a.
A401284

Install a new washer.


Hide 27360 5.INSTALL GENERATOR COIL ASSEMBLY

a.
A401457C01
0.813,0.406 1.615,0.635 true 0.646,0.302 0.958,0.5 0.313,0.198 10 false *a
*a 21 mm Deep Socket Wrench


Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.


b.
A401455

Install the generator coil assembly with the 4 through bolts.

Torque:

5.9 N*m (60 kgf*cm, 52 in.*lbf)



Hide 27370 6.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A160030C01
1.333,0.438 0.885,0.573 false 1.344,0.302 1.656,0.5 0.313,0.198 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the brush holder hole.


b.
A157275C01
1.802,1.417 1.802,1.25 false 1.719,1.406 2.031,1.604 0.313,0.198 10 false *a
*a Pin


Install the generator brush holder assembly with the 2 screws.

Torque:

1.8 N*m (18 kgf*cm, 16 in.*lbf)



c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 7.INSTALL TERMINAL INSULATOR

a.
A157281

Install the terminal insulator.

NOTICE:

Be sure to install the terminal insulator in the correct direction.



Hide 27039 8.INSTALL REAR GENERATOR END COVER

a.
A401454

Install the rear generator end cover with the 3 nuts.

Torque:

4.6 N*m (46 kgf*cm, 40 in.*lbf)



Hide 27411 9.INSTALL GENERATOR PULLEY

a.

Temporarily install the generator pulley by hand.


b.
A401450C04
2.563,1.823 2.844,0.781 true 3.052,2.323 3.219,2.323 3.219,2.323 2.99,0.667 true 1.615,3.042 1.927,3.24 0.313,0.198 10 false *a 0.469,2.354 0.677,2.531 0.208,0.177 10 false *b 2.25,1.875 2.948,2.073 0.698,0.198 10 false SST 1-B 2.479,2.24 3.177,2.438 0.698,0.198 10 false SST 1-A
*a Hold
*b Turn


Mount the generator assembly in a vise between aluminum plates.


c.

Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and SST 1-B 09820-06010


d.

Install SST 1-B to SST 1-A.


e.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:

39 N*m (398 kgf*cm, 29 ft.*lbf)


NOTICE:

Make sure that SST is secured to the generator rotor shaft.



f.
A401451C05
2.458,1.719 2.573,1.396 false 2.031,1.469 2.344,1.667 0.313,0.198 10 false *a 2.271,1.74 2.729,1.906 0.458,0.167 10 false SST 2
*a Insert


Insert SST 2 and attach it to the generator pulley nut.

Item Part No.
SST 2 09820-06021


g.
A401458C02
0.531,2.344 0.844,2.542 0.313,0.198 10 false *a 2.99,1.323 3.302,1.521 0.313,0.198 10 false *b
*a Hold
*b Turn


Tighten the generator pulley nut by turning SST 1- A in the direction shown in the illustration.

Torque:

132.5 N*m (1351 kgf*cm, 98 ft.*lbf)



h.

Remove SST 2 from the generator assembly.


i.
A401453C03
2.323,1.906 2.844,0.781 true 3.073,2.375 3.24,2.375 3.24,2.375 3,0.656 true 2.042,2.938 2.354,3.135 0.313,0.198 10 false *a 1.083,2.75 1.396,2.948 0.313,0.198 10 false *b 2.052,1.948 2.677,2.146 0.625,0.198 10 false SST 1-B 2.51,2.302 3.135,2.5 0.625,0.198 10 false SST 1-A
*a Hold
*b Turn


Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and B.


j.

Turn the generator pulley and check that the generator pulley moves smoothly.