Home › Engine / Hybrid System › N04C-VJ (LUBRICATION) › LUBRICATION SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096893 N04C-VJ LUBRICATION _0461230 LUBRICATION SYSTEM G

N04C-VJ LUBRICATION  LUBRICATION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FOR OIL QUALITY

a.

Check the engine oil for deterioration, water contamination, discoloration or thinning. If the quality is visibly poor, replace the engine oil and oil filter sub-assembly.


Hide 2.INSPECT ENGINE OIL LEVEL

a.

Warm up the engine, then stop the engine and wait for 5 minutes.


b.

Check that the engine oil level is between the low level and full level marks on the level dip stick.

NOTICE:
·

If low, check for leakage and add oil up to the full level mark.

·

Do not fill with engine oil to above the full level mark.



HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

·

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

·

If low quality oil or oil of an inappropriate viscosity is used.

·

When driving at high engine speed or with a heavy load, (when towing or), when driving while accelerating or decelerating frequently.

·

When idling for a long time, or when driving frequently through heavy traffic.


When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



Hide 3.INSPECT FOR ENGINE OIL PRESSURE

a.

Remove the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-VJ (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.
A252304C03
1,3.365 1.5,3.365 false 0.948,3.792 1.448,3.792 false 1.01,4.198 1.51,4.198 false 2.417,3.688 2.583,3.354 2.583,3.354 2.75,3.354 false 0.979,2.698 1.281,2.698 1.281,2.698 1.563,2.698 false 2.365,0.5 2.698,0.5 false 0.333,0.5 0.667,0.5 true 0.813,2.604 1.167,2.844 0.354,0.24 10 false *a 0.833,3.281 1.146,3.479 0.313,0.198 10 false *b 0.781,3.708 1.115,3.938 0.333,0.229 10 false *c 2.792,3.271 3.104,3.5 0.313,0.229 10 false *d 0.833,4.135 1.146,4.333 0.313,0.198 10 false *b 0.125,0.406 0.354,0.656 0.229,0.25 10 true *1 2.198,0.427 2.552,0.667 0.354,0.24 10 false *e
*1 Engine Oil Pressure Switch Assembly
*a Union Bolt
*b Gasket
*c Union
*d Adapter
*e Oil Pressure Gauge


Install the union and 2 new gaskets to the oil cooler cover sub-assembly with the union bolt.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

Parts List (Reference)
Union bolt 90034-01011
Union 90404-10024


c.

Install an oil pressure gauge with an adapter.


d.

Warm up the engine.


e.

Measure the engine oil pressure.

Oil pressure:
Engine condition Specification
Idling 190 kPa (1.9 kgf/cm2, 27.6 psi)


HINT:

If the pressure is not as specified, check the oil pump.



f.

Remove the oil pressure gauge and adapter.


g.

Remove the union bolt, union and 2 gaskets.


h.

Install the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-VJ (LUBRICATION)>OIL PRESSURE SWITCH>INSTALLATION