11131
1.REPLACE INTAKE VALVE SEAT
| *1 | Brass Block |
| *2 | Intake Valve Seat |
| *3 | Intake Valve |
| *a | Grind these Points with a Grinder |
| *b | Weld Application Point |
As shown in the illustration, grind the 3 points on the circumference of an unneeded intake valve and weld it to the intake valve seat.
To protect the lower surface of the cylinder head sub-assembly from welding spatters, be sure to apply grease to the cylinder head sub-assembly before welding.
Place a brass block on the top of the valve stem and strike it with a hammer to remove the intake valve seat.
When striking, metal shards may fly off on impact. Wear safety glasses to protect your eyes.
Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation holes.
| Item | Specification Condition |
|---|---|
|
If the result is not specified, replace the cylinder head sub-assembly. |
|
| A | 36.000 to 36.016 mm (1.4173 to 1.4179 in.) |
| B | 8.4 to 8.6 mm (0.331 to 0.339 in.) |
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
Using SST and a hammer, lightly tap new intake valve seats into the cylinder head sub-assembly.
| SST 1 | 09951-07100 |
| SST 2 | 09952-06010 |
| SST 3 | 09951-00360 |
| SST 4 | 09951-00300 |
Using SST and a hammer, completely tap in the intake valve seats.
11135
2.REPLACE EXHAUST VALVE SEAT
| *1 | Brass Block |
| *2 | Exhaust Valve Seat |
| *3 | Exhaust Valve |
| *a | Grind these Points with a Grinder |
| *b | Weld Application Point |
As shown in the illustration, grind the 3 points on the circumference of an unneeded exhaust valve and weld it to the exhaust valve seat.
To protect the lower surface of the cylinder head sub-assembly from welding spatters, be sure to apply grease to the cylinder head sub-assembly before welding.
Place a brass block on the top of the valve stem and strike it with a hammer to remove the valve seat.
When striking, metal shards may fly off on impact. Wear safety glasses to protect your eyes.
Using a caliper gauge and vernier caliper, measure the dimensions of the valve seat installation holes.
| Item | Specified Condition |
|---|---|
|
If the result is not specified, replace the cylinder head sub-assembly. |
|
| A | 32.000 to 32.016 mm (1.2598 to 1.2602 in.) |
| B | 7.6 to 7.8 mm (0.299 to 0.307 in.) |
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
Using SST and a hammer, lightly tap new exhaust valve seats into the cylinder head sub-assembly.
| SST 1 | 09951-07100 |
| SST 2 | 09952-06010 |
| SST 3 | 09951-00360 |
| SST 4 | 09951-00300 |
Using SST and a hammer, completely tap in the exhaust valve seats.
11122
3.REPLACE INTAKE VALVE GUIDE BUSH
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
Using SST and a hammer, tap out the intake valve guide bush.
Using a caliper gauge, measure the inside diameter of the intake valve guide bush.
13.000 to 13.018 mm (0.512 to 0.513 in.)
If the bush bore diameter of the cylinder head sub-assembly is more than 13.02 mm (0.515 in.), replace the cylinder head sub-assembly.
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
| *a | Protrusion height |
Using SST, tap in a new intake valve guide bush.
26.4 to 26.8 mm (1.04 to 1.06 in.)
Do not tap in the intake valve guide bush excessively.
Using a reamer, ream the inside of the intake valve guide bush to the specified oil clearance between the intake valve guide bush and intake valve stem.
0.028 to 0.058 mm (0.00110 to 0.00228 in.)
0.12 mm (0.00472 in.)
11126
4.REPLACE EXHAUST VALVE GUIDE BUSH
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
Using SST and a hammer, tap out the exhaust valve guide bush.
Using a caliper gauge, measure the inside diameter of the exhaust valve guide bush.
13.000 to 13.018 mm (0.512 to 0.513 in.)
If the bush bore diameter of the cylinder head sub-assembly is more than 13.02 mm (0.5125 in.), replace the cylinder head sub-assembly.
Heat the cylinder head sub-assembly up to 80 to 100°C (176 to 212°F).
| *a | Protrusion height |
Using SST, tap in a new exhaust valve guide bush.
26.4 to 26.8 mm (1.04 to 1.06 in.)
Do not tap in the exhaust valve guide bush excessively.
Using a reamer, ream the inside of the exhaust valve guide bush to the specified oil clearance between the exhaust valve guide bush and exhaust valve stem.
0.053 to 0.083 mm (0.00209 to 0.00327 in.)
0.15 mm (0.00591 in.)
11176
5.REPLACE INJECTION NOZZLE SEAT
Using SST, remove the injection nozzle seat.
Remove the O-ring from the cylinder head sub-assembly.
| *1 | Cylinder Head Sub-assembly |
| *2 | O-Ring |
| *3 | Injection Nozzle Seat |
Apply a light coat of engine oil to new O-rings, and install them into the cylinder head sub-assembly.
Be sure to install new O-rings. Reusing O-rings may cause water or gas leakage and lead to overheating or a cracked cylinder head sub-assembly.
| *a | Seal Packing |
Apply seal packing to new injection nozzle seats.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the installation surfaces of the cylinder head sub-assembly and injection nozzle seats.
Be sure to install new injection nozzle seats. Reusing injection nozzle seats may cause water or gas leakage and lead to overheating or a cracked cylinder head sub-assembly.
| *1 | Injection Nozzle Seat |
Using SST, install the injection nozzle seat onto the cylinder head sub-assembly.
| *1 | Injection Nozzle Seat |
Using SST, stake the injection nozzle seat.
Put a container under the cylinder head sub-assembly to prevent the steel ball from being lost.