Home › Engine / Hybrid System › N04C-VJ (EMISSION CONTROL) › EXHAUST GAS TEMPERATURE SENSOR › from 2021.01
RM2850E _51 Engine / Hybrid System _096890 N04C-VJ EMISSION CONTROL _0461594 EXHAUST GAS TEMPERATURE SENSOR A

N04C-VJ EMISSION CONTROL  EXHAUST GAS TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 4 EXHAUST GAS TEMPERATURE SENSOR

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, install the No. 4 exhaust gas temperature sensor.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 4 exhaust gas temperature sensor is dropped, replace it with a new one.

·

If water or oil is attached to the inside of the connector, do not use the connector.

·

Make sure that the sensor installation threads are free of deformation and foreign matter.

·

Check that the connector and clamp are securely connected.

·

When reusing the No. 4 exhaust gas temperature sensor, clean the threads and apply anti-seize compound before installing it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 25.7 N*m (262 kgf*cm, 19 ft.*lbf)




b.

Connect the No. 4 exhaust gas temperature sensor connector and attach the 2 clamps.


Hide 2.INSTALL NO. 3 EXHAUST GAS TEMPERATURE SENSOR

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, install the No. 3 exhaust gas temperature sensor.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 3 exhaust gas temperature sensor is dropped, replace it with a new one.

·

If water or oil is attached to the inside of the connector, do not use the connector.

·

Make sure that the sensor installation threads are free of deformation and foreign matter.

·

Check that the connector and clamp are securely connected.

·

When reusing the No. 3 exhaust gas temperature sensor, clean the threads and apply anti-seize compound before installing it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 25.7 N*m (262 kgf*cm, 19 ft.*lbf)




b.

Connect the No. 3 exhaust gas temperature sensor connector and attach the clamp.


Hide 3.INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, install the No. 2 exhaust gas temperature sensor.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the No. 2 exhaust gas temperature sensor is dropped, replace it with a new one.

·

If water or oil is attached to the inside of the connector, do not use the connector.

·

Make sure that the sensor installation threads are free of deformation and foreign matter.

·

Check that the connector and clamp are securely connected.

·

When reusing the No. 2 exhaust gas temperature sensor, clean the threads and apply anti-seize compound before installing it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 25.7 N*m (262 kgf*cm, 19 ft.*lbf)




b.

Connect the No. 2 exhaust gas temperature sensor connector and attach the clamp.


Hide 4.INSTALL EXHAUST GAS TEMPERATURE SENSOR

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the exhaust gas temperature sensor.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

If the exhaust gas temperature sensor is dropped, replace it with a new one.

·

If water or oil is attached to the inside of the connector, do not use the connector.

·

Make sure that the sensor installation threads are free of deformation and foreign matter.

·

Check that the connector and clamp are securely connected.

·

When reusing the exhaust gas temperature sensor, clean the threads and apply anti-seize compound before installing it.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




b.

Connect the exhaust gas temperature sensor connector and attach the 4 clamps.