Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM U

N04C-UH ENGINE CONTROL  ECD SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Notes
Vehicle Speed Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
Idling: 600 to 700 rpm After warming-up engine
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
Idling: 10 to 25%
Running without load (2500 rpm): 7.5 to 14.5%
-
MAF Air flow rate from mass air flow meter sub-assembly:
Min.: 0 gm/s, Max.: 655.35 gm/s
Idling: 5.0 to 20.0 gm/s
Running without load (3000 rpm): 70 to 90 gm/s
0 gm/s: Mass air flow meter sub-assembly power source circuit is open or VG circuit is open/shorted
160.1 gm/s or more: E2G circuit is open
Atmosphere Pressure Atmospheric pressure value:
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1912.6 mmHg, 75.3 in.Hg)
Actual atmospheric pressure -
MAP Absolute pressure inside intake manifold:
Min.: 0 kPa, Max.: 255 kPa
·

Idling: 90 to 100 kPa or less

·

Engine running at 3000 rpm: 110 to 140 kPa or more


-
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.: 140°C
After warming up engine: 80 to 100°C (176 to 212°F) If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Intake air temperature:
Min.: -40°C, Max.: 140°C
Equivalent to temperature at intake manifold If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Temp (Turbo) Intake air temperature (Turbo):
Min.: -40°C to 190°C
- -
Engine Run Time Engine run time:
Min.: 0 s Max.: 65535 s
Time after engine started Service data
Initial Engine Coolant Temp Initial engine coolant temperature:
Min.: -40°C, Max.: 120°C
Engine coolant temperature when engine starts -
Initial Intake Air Temp Initial intake air temperature:
Min.: -40°C, Max.: 120°C
Intake air temperature when engine starts -
Battery Voltage Battery voltage:
Min.: 0 V Max.: 65.5 V
Idling: 11 to 14 V -
Accel Position Accelerator position status:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 0%

·

Accelerator pedal depressed: 68 to 99.6%


-
Accel Sens. No. 1 Volt % Accelerator position No. 1:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 12 to 20%

·

Accelerator pedal depressed: 56 to 72%


-
Accel Sens. No. 2 Volt % Accelerator position No. 2:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 28 to 36%

·

Accelerator pedal depressed: 72 to 88%


-
Accel Sensor Out No. 1 Accelerator position No. 1 voltage:
Min.: 0 V, Max.: 5 V
·

0.6 to 1.0 V: Accelerator pedal released

·

2.8 to 3.6 V: Accelerator pedal fully depressed


Read value with ignition switch ON (Do not start engine)
Accel Sensor Out No. 2 Accelerator position No. 2 voltage:
Min.: 0 V, Max.: 5 V
·

1.4 to 1.8 V: Accelerator pedal released

·

3.6 to 4.4 V: Accelerator pedal fully depressed


Read value with ignition switch ON (Do not start engine)
Actual Throttle Position Diesel throttle angle:
Min.: -128%, Max.: 127%
Idling after warmed-up engine: 30 to 100% -
Throttle Close Learning Val. Throttle valve fully closed:
Min.: 0 deg, Max.: 84 deg
- -
Diesel Throttle Learn Status Diesel throttle learning status:
OK or NG
OK -
Throttle Motor DUTY Throttle actuator output :
Min.: 0%, Max.: 100%
Idling after warming up engine: 30 to 100% -
Injection Volume Injection volume:
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 5.0 to 16.0 mm3/st -
Inj. FB Vol. for Idle Idle stable control:
Min.: -80 mm3/st, Max.: 79.99 mm3/st
-10 to 10 mm3/st ECD freeze frame data
Inj Vol Feedback Learning Injection volume feedback learning value:
Min.: -10 mm3/st, Max.: 9.9 mm3/st
Idling: -0.4 to 1.0 mm3/st -
Injection Feedback Val #1 Injection volume correction for cylinder 1:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #2 Injection volume correction for cylinder 2:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #3 Injection volume correction for cylinder 3:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #4 Injection volume correction for cylinder 4:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Pilot 1 Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling after warming up engine: 0 μs -
Pilot 2 Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling: 500 to 600 μs -
Main Injection Period Main Injection Period
Min.: 0 μs, Max.: 65535 μs
Idling: 650 to 800 μs -
After Injection Period After Injection period:
Min.: 0 μs, Max.: 65535 μs
- -
Pilot 1 Injection Timing Pilot 1 Injection timing:
Min.: -70°CA, Max.: 20°CA
- -
Pilot 2 Injection Timing Pilot 2 Injection timing:
Min.: -50°CA, Max.: 20°CA
Idling: -8 to -6°CA -
Main Injection Timing Main Injection timing:
Min.: -90°CA, Max.: 90°CA
Idling: -1 to 1°CA -
After Injection Timing After Injection timing:
Min.: -10°CA, Max.: 50°CA
- -
Injector Memory Error Injector Memory Error:
No Error or Error
No Error If the injector compensation codes are not input into the new ECM, or if a injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P1601 is stored and "Injector Memory Error" displays "Error".
Injection Pressure Correction Injection pressure correction:
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st -
Target Common Rail Pressure Target common rail pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 25000 to 35000 kPa -
Fuel Press Fuel pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 25000 to 35000 kPa -
Fuel Temperature Fuel temperature:
Min.: -40°C, Max.: 140°C
Actual fuel temperature -
Target Pump SCV Current Pump open current value:
Min.: 0 mA, Max.: 8191.8 mA
Idling: 1350 to 2200 mA ECD freeze frame data
Target EGR Position Target EGR position:
Min.: 0%, Max.: 100%
Idling: 35 to 65% -
EGR Lift Sensor Volt% EGR lift position:
Min.: 0%, Max.: 99.6%
Idling 70 to 90% -
EGR Close Learn Val. EGR close learning value:
Min.: 0 V, Max.: 5 V
- -
EGR Close Lrn. Val. EGR close learning value:
Min.: 0 V, Max.: 5 V
3.5 to 4.5 V -
EGR Close Lrn. Status EGR close learning value:
OK or NG
OK -
VN Turbo Command VN turbo command:
Min.: -128%, Max.: 127%
- -
VN Turbo Type VN turbo type:
Not Avl, Commo, Vacuum, CAN Com or DC
CAN Com -
VN Turbo Max Angle VN turbo maximum angle :
Min.: 0%, Max.: 100%
100% -
VN Turbo Min Angle VN turbo minimum angle :
Min.: 0%, Max.: 100%
7.5% -
Exhaust Temperature B1S1 Exhaust temperature sensor for sensor 1 (upstream):
Min.: 0°C, Max.: 1000°C
Idling: 50 to 150°C
Idling after driving: 80 to 400°C
If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S2 Exhaust temperature sensor for sensor 2 (downstream):
Min.: 0°C, Max.: 1000°C
Idling: 50 to 150°C
Idling after driving: 80 to 400°C
If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
DPF Differential Pressure DPF differential pressure:
Min.: -5 kPa, Max.: 100 kPa
-3 kPa to 3 kPa -
Diff. Press. Sensor Corr. Differential pressure correction:
Min.: -10 kPa, Max.: 246 kPa
Idling: -1.5 to 1.5 kPa -
DPF PM Block DPF particulate matter (PM) Block:
No Block or Blocked
No Block -
DPNR/DPF Status Reju (PM) Result of DPF catalyst regeneration (PM):
Standby, Ready, Operate or Compl
Operate: DPF catalyst regeneration operate -
Catalyst Regeneration Switch DPF switch status:
ON or OFF
ON: DPF switch on -
Exhaust Brake Switch Exhaust brake switch status:
ON or OFF
ON: Exhaust brake operated -
Starter Signal Starter signal:
ON or OFF
ON: Cranking -
IG SW Ignition switch status:
ON or OFF
Ignition switch ON: ON
Ignition switch off: OFF
-
Clutch Switch Exhaust retarder switch status for manual transmission:
ON or OFF
ON: Exhaust retarder switch on for Manual Transmission
Stop Light Switch Stop light switch status:
ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal Air conditioning signal:
ON or OFF
ON: Air conditioning operate -
Check Mode Check mode:
ON or OFF
ON: Check mode on Click here(Click here)
EGR/VVT Monitor EGR/VVT monitor:
Not Avl or Avail
- -
EGR/VVT Monitor EGR/VVT monitor:
Compl or Incmpl
- -
# Codes(Include History) Number of codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
ON: MIL ON -
MIL ON Run Distance MIL ON run distance:
Min.: 0 km, Max.: 65535 km
Distance after DTC detected -
Running Time from MIL ON Running time from MIL on:
Min.: 0 min, Max.: 65535 min
Equivalent running time after MIL was on -
Time after DTC Cleared Time after DTC cleared:
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs were erased -
Distance from DTC Cleared Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs were erased -
Warmup Cycle Cleared DTC Warm up cycle after DTC cleared:
Min.: 0 Max.: 255
- Number of warm up cycles after DTC cleared
OBD Requirements Identifying OBD requirement EURO 5 -
Number of Emission DTC (Number of emission DTC) - -
TC and TE1 TC and TE1 terminal of DLC3:
ON or OFF
- -
Engine Warm Up Switch Warm up switch status:
ON or OFF
ON: Warm up switch on -
ACT VSV Air conditioning cut signal:
ON or OFF
- -
Model Code Model code - Identifying model code: XZB##
Engine Type Engine type - Identifying engine type: N04CUH
Cylinder Number Identifying cylinder number:
Min.: 0, Max.: 255
- Identifying cylinder number: 4
Transmission Type Transmission type - Identifying transmission type: MT or ECT 4th
Destination Destination - Identifying destination: W, Q,
Model Year Identifying model year:
Min.: 1900, Max.: 2155
- Identifying model year: 20##
System Identification Identifying engine system - Identifying engine system: Diesel
Target Engine Speed Target engine speed:
Min.: 0 rpm, Max.: 5000 rpm
Idling: 600 to 700 rpm -
Target Common Rail Press Target common rail pressure:
Min.: 0 MPa, Max.: 256 MPa
Idling after warming up engine: 25 to 35 MPa -
Catalyst Warm Up Malfunction Catalyst warm up malfunction:
ON or OFF
OFF -
Manual Catalyst Regeneration Manual catalyst regeneration status:
ON or OFF
OFF -
Pump Mode Supply pump control model:
PCV, DUTY, IG OFF, STOP or Normal
- -
Catalyst Malfunction Catalyst malfunction (differential pressure detection):
ON or OFF
OFF -
Clogged Catalyst Clogged catalyst (differential pressure detection):
ON or OFF
OFF -
Heat Catalyst Catalyst temperature malfunction:
ON or OFF
OFF -
Clogged Catalyst Warning Clogged catalyst warning status
SAFE, Danger or Warning
SAFE -
Catalyst Deteriorate DPF catalyst deteriorate:
ON or OFF
OFF -
Exhaust Fuel Addition Exhaust fuel addition malfunction:
ON or OFF
OFF -
DPF Mode DPF model/
Under, Normal, N/EGR, Warm, Warm/Idl, PM, PM/Idl or S Dchg
Normal -
Injection Pump Learning Status Injection pump learning status:
Compl or Incmpl
Compl -
VN Turbo Valve Position Turbocharger opening value:
Min.: 0% Max.: 100%
- -
PCV Open Duty Suction control valve open duty:
Min.: 0% Max.: 100%
45 to 55% -
PCV Open Current FB Val Suction control valve open current feedback volume:
Min.: -6000 mA, Max.: 6000 mA
-400 to 400 mA -
Intake Water History Intake the water in history:
ON or OFF
OFF -
Engine Overspeed History Engine overspeed history:
ON or OFF
OFF -

HINT:

Normal Condition: If no idling conditions are specified, the shift lever is in the neutral position, and the A/C switch and all accessory switches are off.




PERFORM ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the "Active Test".

Tester Display Test Part Control Range Diagnostic Notes
Control the A/C Cut Signal Control the air conditioning cut signal ON or OFF Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Connect the TC and TE1 Turn on TC and TE1 connection ON or OFF Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Control the EGR Step Position Control the EGR valve step position 0 to 100% Test possible when following conditions met:
·

Confirm that the vehicle is stopped and the engine is idling.


Activate the DPF Rejuvenate (PM) DPF catalyst regeneration (PM) raises temperature of DPF to more than 600°C (1112°F) by adding fuel intermittently ON or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling


Test the Turbo Charger Step Motor Control the turbocharger actuator 40 to 100% Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped

·

Accelerator pedal fully released


Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop or Start Test possible when following conditions met:
·

Warm up the engine

·

Engine idling

·

Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected

·

Above conditions preserved while test is ON


Active the VN Turbo Open Activate the turbocharger Open or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling


Active the EGR Valve Close Activate the EGR Valve Close or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling

·

Shift lever in neutral


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #4) injector fuel cut ON or OFF Fuel injection is stopped while the test is ON.
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be confirmed to be malfunctioning


Activate the VSV for Exhaust Brake Activate the solenoid valve for exhaust brake ON or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling