Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Transmission Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Transmission Control ECU Communication Stop Mode Any of the following conditions are met:
·

"ECT" cannot be normally selected on the system selection screen of the GTS

·

Communication system DTCs (DTCs that start with U) that correspond to "Transmission Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

(Click here)


·

Transmission control ECU branch wire or connector

·

Power source circuit of transmission control ECU assembly

·

Transmission control ECU assembly ground circuit

·

Transmission control ECU assembly



WIRING DIAGRAM

C358922E01
1.583,0.625 1.896,0.823 0.313,0.198 10 false 7 1.563,1.073 1.875,1.271 0.313,0.198 10 false 18 5.313,0.615 5.625,0.813 0.313,0.198 10 false 11 5.323,1.042 5.635,1.24 0.313,0.198 10 false 12 5.385,1.74 5.698,1.938 0.313,0.198 10 false 7 5.385,2.292 5.698,2.49 0.313,0.198 10 false 3 5.385,2.813 5.698,3.01 0.313,0.198 10 false 4 5.385,3.365 5.698,3.563 0.313,0.198 10 false 8 5.323,3.823 5.635,4.021 0.313,0.198 10 false 17 5.594,0.75 6.208,0.948 0.615,0.198 10 false CANH 5.583,1.167 6.198,1.365 0.615,0.198 10 false CANL 5.594,1.854 6.208,2.052 0.615,0.198 10 false +B 5.594,2.396 6.208,2.594 0.615,0.198 10 false IG2 5.594,2.927 6.208,3.125 0.615,0.198 10 false IG 5.594,3.469 6.208,3.667 0.615,0.198 10 false E 5.573,3.938 6.188,4.135 0.615,0.198 10 false GND 3.833,1.708 4.771,1.885 0.938,0.177 10 false ECU-B NO. 3 3.917,2.26 4.625,2.438 0.708,0.177 10 false IGN NO. 2 2.073,1.833 3.063,2.073 0.99,0.24 10 false from Battery 1.948,2.375 2.885,2.615 0.938,0.24 10 false from IG2 relay 0.104,1.323 0.719,1.521 0.615,0.198 10 false A123 0.104,1.531 1.375,1.969 1.271,0.438 10 false No. 7 CAN Junction Connector 4.948,4.563 5.563,4.76 0.615,0.198 10 false B133 4.958,4.74 6.635,5.188 1.677,0.448 10 false Transmission Control ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TRANSMISSION CONTROL ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C358903C05
1.458,0.323 1.896,0.604 0.438,0.281 1.406,2.833 1.542,2.833 1.542,2.833 1.542,1.896 true 1.865,2.844 1.719,2.844 1.719,2.844 1.719,1.906 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 1.531,0.375 1.979,0.615 0.448,0.24 10 false B133 1.01,2.781 1.563,2.99 0.552,0.208 10 false CANH 1.917,2.771 2.448,2.99 0.531,0.219 10 false CANL
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-11 (CANH) - B133-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C358903C06
1.458,0.323 1.896,0.604 0.438,0.281 0.667,2.042 0.802,2.042 0.802,2.042 1.042,1.854 true 2.354,0.719 2.208,0.719 2.208,0.719 1.771,1.5 true 0.667,2.406 0.802,2.406 0.802,2.406 1.073,2.135 true 0.708,0.885 0.844,0.885 0.844,0.885 1.51,1.479 true 2.802,1.292 2.656,1.292 2.656,1.292 2.365,1.531 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 1.531,0.375 1.948,0.594 0.417,0.219 10 false B133 0.521,1.979 1.073,2.188 0.552,0.208 10 false E 2.406,0.635 2.938,0.854 0.531,0.219 10 false IG 0.323,2.333 0.875,2.542 0.552,0.208 10 false GND 0.458,0.792 1.01,1 0.552,0.208 10 false IG2 2.854,1.208 3.198,1.427 0.344,0.219 10 false +B
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-8 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B133-17 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B133-3 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
B133-4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
B133-7 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR