Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Bus 4 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Detection Item Trouble Area

*1: w/ Airbag System

*2: w/o Airbag System

*3: for LHD

*4: for RHD

*5: except 1HZ

*6: for 1HZ

No resistance exists between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main wires

·

Short to +B in CAN branch wires

·

Central gateway ECU (network gateway ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Brake actuator assembly (skid control ECU)

·

Airbag ECU assembly*1

·

No. 1 CAN junction terminal*2

·

No. 3 CAN junction connector*5

·

No. 11 CAN junction connector*6

·

No. 63 junction connector*3

·

No. 67 junction connector*4

·

No. 73 junction connector*2



WIRING DIAGRAM

C454807E01
1.635,0.281 2.865,0.479 1.229,0.198 10 false 3*3, 7*4 1.573,0.823 2.802,1.021 1.229,0.198 10 false 6*3, 18*4 2.844,0.302 4.073,0.5 1.229,0.198 10 false 1*3, 5*4 2.854,0.823 4.083,1.021 1.229,0.198 10 false 4*3, 16*4 2.854,1.354 4.083,1.552 1.229,0.198 10 false 2*3, 6*4 2.865,1.875 4.094,2.073 1.229,0.198 10 false 5*3, 17*4 1.26,2.115 2.49,2.313 1.229,0.198 10 false J90*3, J81*4 1.26,2.302 3.052,2.656 1.792,0.354 10 false No. 63 Junction Connector*3, No. 67 Junction Connector*4 3.448,2.177 4.677,2.375 1.229,0.198 10 false J71 3.438,2.323 5.865,2.667 2.427,0.344 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 5.406,1.167 6.635,1.365 1.229,0.198 10 false J51 5.385,1.365 6.906,1.75 1.521,0.385 10 false Central Gateway ECU (Network Gateway ECU) 5.958,0.302 6.573,0.5 0.615,0.198 10 false CA2H 5.969,1.083 6.583,1.281 0.615,0.198 10 false CA2L 5.958,3.042 6.573,3.24 0.615,0.198 10 false CANH 5.948,3.604 6.563,3.802 0.615,0.198 10 false CANL 5.948,6.125 6.563,6.323 0.615,0.198 10 false CANH 5.948,6.875 6.563,7.073 0.615,0.198 10 false CANL 3.375,4.177 3.99,4.375 0.615,0.198 10 false CANH 3.385,4.917 4,5.115 0.615,0.198 10 false CANL 3.958,1.458 4.573,1.656 0.615,0.198 10 false CANH 3.948,2.01 4.563,2.208 0.615,0.198 10 false CANL 1.833,3.75 4.958,3.99 3.125,0.24 12 false w/ Airbag System: 1.833,5.594 5.135,5.833 3.302,0.24 12 false w/o Airbag System: 5.458,3.792 5.917,3.99 0.458,0.198 10 false A71 5.573,6.948 6.031,7.146 0.458,0.198 10 false A76 2.979,5 3.438,5.198 0.458,0.198 10 false A58 1.875,7.188 2.844,7.375 0.969,0.188 10 false A96 0.094,7.188 1.104,7.375 1.01,0.188 10 false A91*5, A127*6 5.458,3.969 7.052,4.323 1.594,0.354 10 false Brake Actuator Assembly (Skid Control ECU) 3,5.188 4.594,5.542 1.594,0.354 10 false Airbag ECU Assembly 5.583,7.135 6.813,7.49 1.229,0.354 10 false No. 1 CAN Junction Terminal 0.073,7.365 1.688,7.885 1.615,0.521 10 false No. 3 CAN Junction Connector*5, No. 11 CAN Junction Connector*6 0.115,8.365 3.177,8.563 3.063,0.198 10 false *1: w/ Airbag System 1.74,8.229 4.802,8.427 3.063,0.198 10 false *2: w/o Airbag System 1.74,8.531 2.552,8.771 0.813,0.24 10 false *3: for LHD 3.479,8.24 4.385,8.458 0.906,0.219 10 false *4: for RHD 1.135,6.635 1.594,6.833 0.458,0.198 10 false 8*2 1.125,6.083 1.583,6.281 0.458,0.198 10 false 6*2 2.052,6.063 2.51,6.26 0.458,0.198 10 false 1 2.01,6.646 2.469,6.844 0.458,0.198 10 false 12 2.854,6.104 3.313,6.302 0.458,0.198 10 false 3 2.844,6.635 3.302,6.833 0.458,0.198 10 false 14 5.771,6.094 6.229,6.292 0.458,0.198 10 false 3 5.771,6.635 6.229,6.833 0.458,0.198 10 false 2 3.125,4.156 3.583,4.354 0.458,0.198 10 false 13 3.125,4.688 3.583,4.885 0.458,0.198 10 false 22 1.125,4.115 1.583,4.313 0.458,0.198 10 false 5*1 1.135,4.677 1.594,4.875 0.458,0.198 10 false 7*1 1.135,3.438 1.594,3.635 0.458,0.198 10 false 4 1.125,2.896 1.583,3.094 0.458,0.198 10 false 2 5.698,2.896 6.156,3.094 0.458,0.198 10 false 22 5.708,3.427 6.167,3.625 0.458,0.198 10 false 10 3.76,1.323 4.219,1.521 0.458,0.198 10 false 4 3.76,1.854 4.219,2.052 0.458,0.198 10 false 3 5.688,0.313 6.146,0.51 0.458,0.198 10 false 22 5.76,0.813 6.219,1.01 0.458,0.198 10 false 7 1.125,0.302 1.583,0.5 0.458,0.198 10 false 1 1.125,0.844 1.583,1.042 0.458,0.198 10 false 3 1.875,7.375 3.667,7.74 1.792,0.365 10 false No. 73 Junction Connector 3.458,8.521 4.552,8.719 1.094,0.198 10 false *5: except 1HZ 4.875,8.24 5.969,8.438 1.094,0.198 10 false *6: for 1HZ

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
except 1HZ A
for 1HZ B



A

2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.

C358915E03
5.125,0.094 5.51,0.323 0.385,0.229 1.563,0.125 1.958,0.365 0.396,0.24 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 6.083,1.5 5.906,1.5 5.906,1.5 5.906,1.135 true 2.458,1.313 2.302,1.313 2.302,1.313 2.052,1.063 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1.031,1.313 1.198,1.313 1.198,1.313 1.51,1.052 true 1.135,1.563 1.281,1.563 1.281,1.563 1.677,1.052 true 2.302,1.552 2.125,1.552 2.125,1.552 1.875,1.083 true 1.635,0.156 2.094,0.354 0.458,0.198 10 false A91 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 6.156,1.427 6.635,1.646 0.479,0.219 10 false BAT 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.479,1.219 1.396,1.417 0.917,0.198 10 false CANH*e 2.542,1.229 3.458,1.427 0.917,0.198 10 false CANL*f 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 2.354,1.469 3.271,1.667 0.917,0.198 10 false CANL*e 0.604,1.469 1.521,1.667 0.917,0.198 10 false CANH*f

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3
*c
·

to No. 63 Junction Connector (for LHD)

·

to No. 67 Junction Connector (for RHD)


*d to Brake Actuator Assembly (Skid Control ECU)
*e to Airbag ECU Assembly (w/ Airbag System) *f to No. 73 Junction Connector (w/o Airbag System)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Airbag System

*2: w/o Airbag System

*3: for LHD

*4: for RHD

A91-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

No. 63 junction connector*3

·

No. 67 junction connector*4


A91-3 (CANL) - J45-16 (BAT)
A91-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly (skid control ECU)
A91-4 (CANL) - J45-16 (BAT)
A91-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag ECU assembly*1
A91-7 (CANL) - J45-16 (BAT)
A91-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 73 junction connector*2
A91-8 (CANL) - J45-16 (BAT)




Result:
Result Proceed to
OK A
NG (No. 63 junction connector CAN main wire [for LHD]) B
NG (No. 67 junction connector CAN main wire [for RHD]) C
NG (No. 73 junction connector CAN main wire [w/o Airbag System]) D
NG (ECU or sensor CAN wires) E



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 67 JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 73 JUNCTION CONNECTOR)

E

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 11 CAN junction connector.

C358915E06
5.125,0.094 5.51,0.323 0.385,0.229 1.563,0.125 2.031,0.365 0.469,0.24 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 6.083,1.5 5.906,1.5 5.906,1.5 5.906,1.135 true 2.458,1.313 2.302,1.313 2.302,1.313 2.052,1.063 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1.031,1.313 1.198,1.313 1.198,1.313 1.51,1.052 true 1.135,1.563 1.281,1.563 1.281,1.563 1.677,1.052 true 2.302,1.552 2.125,1.552 2.125,1.552 1.875,1.083 true 1.635,0.156 2.094,0.354 0.458,0.198 10 false A127 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 6.156,1.427 6.635,1.646 0.479,0.219 10 false BAT 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.479,1.219 1.396,1.417 0.917,0.198 10 false CANH*e 2.542,1.229 3.458,1.427 0.917,0.198 10 false CANL*f 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 2.354,1.469 3.271,1.667 0.917,0.198 10 false CANL*e 0.604,1.469 1.521,1.667 0.917,0.198 10 false CANH*f

Text in Illustration
*a Front view of wire harness connector
(to No. 11 CAN Junction Connector)
*b Front view of DLC3
*c
·

to No. 63 Junction Connector (for LHD)

·

to No. 67 Junction Connector (for RHD)


*d to Brake Actuator Assembly (Skid Control ECU)
*e to Airbag ECU Assembly (w/ Airbag System) *f to No. 73 Junction Connector (w/o Airbag System)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Airbag System

*2: w/o Airbag System

*3: for LHD

*4: for RHD

A127-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

No. 63 junction connector*3

·

No. 67 junction connector*4


A127-3 (CANL) - J45-16 (BAT)
A127-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly (skid control ECU)
A127-4 (CANL) - J45-16 (BAT)
A127-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag ECU assembly*1
A127-7 (CANL) - J45-16 (BAT)
A127-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 73 junction connector*2
A127-8 (CANL) - J45-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 63 junction connector CAN main wire [for LHD]) B
NG (No. 67 junction connector CAN main wire [for RHD]) C
NG (No. 73 junction connector CAN main wire [w/o Airbag System]) D
NG (ECU or sensor CAN wires) E



A

REPLACE NO. 11 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 67 JUNCTION CONNECTOR)

D

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 73 JUNCTION CONNECTOR)

E

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)
a.

except 1HZ:

Reconnect the A91 No. 3 CAN junction connector.


b.

for 1HZ:

Reconnect the A127 No. 11 CAN junction connector.


c.

Disconnect the No. 63 junction connector.


d.
C358916E01
1.49,2.708 1.854,2.938 0.365,0.229 0.229,1.125 0.594,1.354 0.365,0.229 1.021,1.146 1.021,0.573 1.021,0.573 0.885,0.573 true 1.146,1.135 1.146,0.385 1.146,0.385 1,0.385 true 1.302,1.156 1.302,0.167 1.302,0.167 1.156,0.167 true 1.427,1.146 1.427,0.167 1.427,0.167 1.583,0.167 true 1.542,1.135 1.542,0.406 1.542,0.406 1.688,0.406 true 1.698,1.135 1.698,0.563 1.698,0.563 1.823,0.563 true 2.323,3.813 2.323,4.333 2.323,4.333 2.479,4.333 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.594,0.073 1.51,0.271 0.917,0.198 10 false CANH*e 0.438,0.302 1.354,0.5 0.917,0.198 10 false CANH*d 0.333,0.49 1.25,0.688 0.917,0.198 10 false CANH*c 1.646,0.083 2.563,0.281 0.917,0.198 10 false CANL*c 1.729,0.323 2.646,0.521 0.917,0.198 10 false CANL*d 1.865,0.49 2.781,0.688 0.917,0.198 10 false CANL*e 1.563,2.75 2.479,2.948 0.917,0.198 10 false J45 2.563,4.25 3.115,4.448 0.552,0.198 10 false BAT 0.292,1.167 1.208,1.365 0.917,0.198 10 false J90 0.198,2.563 0.51,2.76 0.313,0.198 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: except 1HZ

*2: for 1HZ

J90-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
J90-4 (CANL) - J45-16 (BAT)
J90-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Spiral with sensor cable sub-assembly (steering angle sensor)
J90-5 (CANL) - J45-16 (BAT)
J90-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

No. 3 CAN junction connector*1

·

No. 11 CAN junction connector*2


J90-6 (CANL) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU)
*d to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*e
·

to No. 3 CAN Junction Connector (except 1HZ)

·

to No. 11 CAN Junction Connector (for 1HZ)




Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) C
NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) D
NG (ECU or sensor CAN wires) E



A

REPLACE NO. 63 JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 63 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 63 JUNCTION CONNECTOR - NO. 11 CAN JUNCTION CONNECTOR)

E

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)
a.

Reconnect the J90 No. 63 junction connector.


b.
C338146E37
0.146,3.333 0.49,3.615 0.344,0.281 1.479,0.333 1.823,0.615 0.344,0.281 2.417,1.219 2.646,0.365 2.646,0.365 2.823,0.365 true 2.323,1.531 2.531,2.156 2.531,2.156 2.708,2.156 true 2.385,3.719 2.594,4.344 2.594,4.344 2.771,4.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.156,2.5 0.469,2.698 0.313,0.198 10 false *b 2.885,0.292 3.323,0.49 0.438,0.198 10 false CA2L 2.781,2.073 3.219,2.271 0.438,0.198 10 false CA2H 2.844,4.271 3.281,4.469 0.438,0.198 10 false BAT 0.208,3.385 0.646,3.583 0.438,0.198 10 false J45 1.552,0.385 1.99,0.583 0.438,0.198 10 false J51

Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-22 (CA2H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-7 (CA2L) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 67 JUNCTION CONNECTOR)
a.

except 1HZ:

Reconnect the A91 No. 3 CAN junction connector.


b.

for 1HZ:

Reconnect the A127 No. 11 CAN junction connector.


c.

Disconnect the No. 67 junction connector.


d.
C358916E03
1.49,2.708 1.854,2.938 0.365,0.229 0.229,1.125 0.594,1.354 0.365,0.229 1.708,1.448 1.969,2.021 1.969,2.021 2.094,2.021 true 1.563,1.406 1.208,2.052 1.208,2.052 1.063,2.052 true 1.552,1.135 1.313,0.49 1.313,0.49 1.167,0.49 true 1.708,1.156 1.813,0.26 1.813,0.26 1.958,0.26 true 2.323,3.813 2.323,4.333 2.323,4.333 2.479,4.333 true 1.875,1.427 2.052,1.813 2.052,1.813 2.208,1.813 true 1.844,1.146 2.083,0.531 2.083,0.531 2.24,0.531 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.021,0.188 2.938,0.385 0.917,0.198 10 false CANH*d 0.615,0.396 1.531,0.594 0.917,0.198 10 false CANH*c 2.156,1.948 3.073,2.146 0.917,0.198 10 false CANL*d 2.271,1.729 3.188,1.927 0.917,0.198 10 false CANL*e 1.563,2.75 2.479,2.948 0.917,0.198 10 false J45 2.563,4.25 3.115,4.448 0.552,0.198 10 false BAT 0.302,1.156 1.219,1.354 0.917,0.198 10 false J81 0.198,2.563 0.51,2.76 0.313,0.198 10 false *b 2.313,0.458 3.229,0.656 0.917,0.198 10 false CANH*e 0.51,1.948 1.427,2.146 0.917,0.198 10 false CANL*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: except 1HZ

*2: for 1HZ

J81-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
J81-16 (CANL) - J45-16 (BAT)
J81-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Spiral with sensor cable sub-assembly (steering angle sensor)
J81-17 (CANL) - J45-16 (BAT)
J81-7 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

No. 3 CAN junction connector*1

·

No. 11 CAN junction connector*2


J81-18 (CANL) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to No. 67 Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU)
*d to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*e
·

to No. 3 CAN Junction Connector (except 1HZ)

·

to No. 11 CAN Junction Connector (for 1HZ)




Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) C
NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) D
NG (ECU or sensor CAN wires) E



A

REPLACE NO. 67 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 67 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 67 JUNCTION CONNECTOR - NO. 11 CAN JUNCTION CONNECTOR)

E

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)
a.

Reconnect the J81 No. 67 junction connector.


b.
C338146E39
0.146,3.333 0.49,3.615 0.344,0.281 1.479,0.333 1.823,0.615 0.344,0.281 2.417,1.219 2.646,0.365 2.646,0.365 2.823,0.365 true 2.323,1.531 2.531,2.156 2.531,2.156 2.708,2.156 true 2.385,3.719 2.594,4.344 2.594,4.344 2.771,4.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.156,2.5 0.469,2.698 0.313,0.198 10 false *b 2.885,0.292 3.323,0.49 0.438,0.198 10 false CA2L 2.781,2.073 3.219,2.271 0.438,0.198 10 false CA2H 2.844,4.271 3.281,4.469 0.438,0.198 10 false BAT 0.208,3.385 0.646,3.583 0.438,0.198 10 false J45 1.552,0.385 1.99,0.583 0.438,0.198 10 false J51

Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-22 (CA2H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-7 (CA2L) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 67 JUNCTION CONNECTOR)

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 73 JUNCTION CONNECTOR)
a.

except 1HZ:

Reconnect the A91 No. 3 CAN junction connector.


b.

for 1HZ:

Reconnect the A127 No. 11 CAN junction connector.


c.

Disconnect the No. 73 junction connector.


d.
C358916N05
1.49,2.708 1.854,2.938 0.365,0.229 0.229,1.125 0.594,1.354 0.365,0.229 1.042,1.198 0.958,0.656 0.958,0.656 0.823,0.656 true 1.302,1.188 1.573,0.438 1.573,0.438 1.729,0.438 true 2.323,3.813 2.323,4.333 2.323,4.333 2.479,4.333 true 1.01,1.406 0.875,1.969 0.875,1.969 0.74,1.969 true 1.313,1.406 1.615,1.958 1.615,1.958 1.771,1.958 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.802,0.365 2.719,0.563 0.917,0.198 10 false CANH*d 0.271,0.573 1.188,0.771 0.917,0.198 10 false CANH*c 1.563,2.75 2.479,2.948 0.917,0.198 10 false J45 2.563,4.25 3.115,4.448 0.552,0.198 10 false BAT 0.292,1.167 1.208,1.365 0.917,0.198 10 false A96 0.198,2.563 0.51,2.76 0.313,0.198 10 false *b 0.219,1.885 1.135,2.083 0.917,0.198 10 false CANL*c 1.844,1.854 2.76,2.052 0.917,0.198 10 false CANL*d

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: except 1HZ

*2: for 1HZ

A96-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

No. 3 CAN junction connector*1

·

No. 11 CAN junction connector*2


A96-12 (CANL) - J45-16 (BAT)
A96-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 CAN junction terminal
A96-14 (CANL) - J45-16 (BAT)


Text in Illustration
*a Front view of wire harness connector
(to No. 73 Junction Connector)
*b Front view of DLC3
*c
·

to No. 3 CAN Junction Connector (except 1HZ)

·

to No. 11 CAN Junction Connector (for 1HZ)


*d to No. 1 CAN Junction Terminal


Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) B
NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) C
NG (ECU or sensor CAN wires) D



A

REPLACE NO. 73 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 73 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 73 JUNCTION CONNECTOR - NO. 11 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464E30
1.479,2.469 1.854,2.771 0.375,0.302 1.5,0.271 1.875,0.573 0.375,0.302 1.313,0.99 1.083,0.365 1.083,0.365 0.906,0.365 true 1.323,1.167 1.323,1.823 1.323,1.823 1.188,1.823 true 2.385,3.646 2.521,4.271 2.521,4.271 2.688,4.271 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.104,2.5 0.417,2.698 0.313,0.198 10 false *b 0.531,0.292 1.146,0.49 0.615,0.198 10 false CA2L 0.781,1.75 1.396,1.948 0.615,0.198 10 false CA2H 2.75,4.198 3.365,4.396 0.615,0.198 10 false BAT 1.552,2.531 2.167,2.729 0.615,0.198 10 false J45 1.573,0.333 2.188,0.531 0.615,0.198 10 false J51

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-22 (CA2H) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-7 (CA2L) - J45-16 (BAT)


Text in Illustration
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR