There may be a short circuit between one of the CAN bus lines and GND when no resistance exists between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Detection Item | Trouble Area |
|---|---|
|
*1: w/ Airbag System *2: w/o Airbag System *3: for LHD *4: for RHD *5: except 1HZ *6: for 1HZ |
|
| No resistance exists between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. | ·
Short to GND in CAN main wires ·
Short to GND in CAN branch wires ·
Central gateway ECU (network gateway ECU) ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Brake actuator assembly (skid control ECU) ·
Airbag ECU assembly*1 ·
No. 1 CAN junction terminal*2 ·
No. 3 CAN junction connector*5 ·
No. 11 CAN junction connector*6 ·
No. 63 junction connector*3 ·
No. 67 junction connector*4 ·
No. 73 junction connector*2 |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check for vehicle type.
| Result | Proceed to |
|---|---|
| except 1HZ | A |
| for 1HZ | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | ·
to No. 63 Junction Connector (for LHD) ·
to No. 67 Junction Connector (for RHD) |
*d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | to Airbag ECU Assembly (w/ Airbag System) | *f | to No. 73 Junction Connector (w/o Airbag System) |
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Airbag System *2: w/o Airbag System *3: for LHD *4: for RHD |
|||
| A91-1 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
No. 63 junction connector*3 ·
No. 67 junction connector*4 |
| A91-3 (CANL) - J45-4 (CG) | |||
| A91-2 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| A91-4 (CANL) - J45-4 (CG) | |||
| A91-5 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag ECU assembly*1 |
| A91-7 (CANL) - J45-4 (CG) | |||
| A91-6 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 73 junction connector*2 |
| A91-8 (CANL) - J45-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 63 junction connector CAN main wire [for LHD]) | B |
| NG (No. 67 junction connector CAN main wire [for RHD]) | C |
| NG (No. 73 junction connector CAN main wire [w/o Airbag System]) | D |
| NG (ECU or sensor CAN wires) | E |
A
B
C
D
E
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 11 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 11 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | ·
to No. 63 Junction Connector (for LHD) ·
to No. 67 Junction Connector (for RHD) |
*d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | to Airbag ECU Assembly (w/ Airbag System) | *f | to No. 73 Junction Connector (w/o Airbag System) |
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Airbag System *2: w/o Airbag System *3: for LHD *4: for RHD |
|||
| A127-1 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
No. 63 junction connector*3 ·
No. 67 junction connector*4 |
| A127-3 (CANL) - J45-4 (CG) | |||
| A127-2 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| A127-4 (CANL) - J45-4 (CG) | |||
| A127-5 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag ECU assembly*1 |
| A127-7 (CANL) - J45-4 (CG) | |||
| A127-6 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 73 junction connector*2 |
| A127-8 (CANL) - J45-4 (CG) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 63 junction connector CAN main wire [for LHD]) | B |
| NG (No. 67 junction connector CAN main wire [for RHD]) | C |
| NG (No. 73 junction connector CAN main wire [w/o Airbag System]) | D |
| NG (ECU or sensor CAN wires) | E |
A
B
C
D
E
except 1HZ:
Reconnect the A91 No. 3 CAN junction connector.
for 1HZ:
Reconnect the A127 No. 11 CAN junction connector.
Disconnect the No. 63 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: except 1HZ *2: for 1HZ |
|||
| J90-1 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| J90-4 (CANL) - J45-4 (CG) | |||
| J90-2 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| J90-5 (CANL) - J45-4 (CG) | |||
| J90-3 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
No. 3 CAN junction connector*1 ·
No. 11 CAN junction connector*2 |
| J90-6 (CANL) - J45-4 (CG) | |||
| *a | Front view of wire harness connector
(to No. 63 Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) |
| *d | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| *e | ·
to No. 3 CAN Junction Connector (exceot 1HZ) ·
to No. 11 CAN Junction Connector (for 1HZ) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) | C |
| NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) | D |
| NG (ECU or sensor CAN wires) | E |
A
B
C
D
E
Reconnect the J90 No. 63 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-22 (CA2H) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J51-7 (CA2L) - J45-4 (CG) |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
except 1HZ:
Reconnect the A91 No. 3 CAN junction connector.
for 1HZ:
Reconnect the A127 No. 11 CAN junction connector.
Disconnect the No. 67 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: except 1HZ *2: for 1HZ |
|||
| J81-5 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| J81-16 (CANL) - J45-4 (CG) | |||
| J81-6 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| J81-17 (CANL) - J45-4 (CG) | |||
| J81-7 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
No. 3 CAN junction connector*1 ·
No. 11 CAN junction connector*2 |
| J81-18 (CANL) - J45-4 (CG) | |||
| *a | Front view of wire harness connector
(to No. 67 Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) |
| *d | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| *e | ·
to No. 3 CAN Junction Connector (except 1HZ) ·
to No. 11 CAN Junction Connector (for 1HZ) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) | C |
| NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) | D |
| NG (ECU or sensor CAN wires) | E |
A
B
C
D
E
Reconnect the J81 No. 67 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-22 (CA2H) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J51-7 (CA2L) - J45-4 (CG) |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
except 1HZ:
Reconnect the A91 No. 3 CAN junction connector.
for 1HZ:
Reconnect the A127 No. 11 CAN junction connector.
Disconnect the No. 73 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: except 1HZ *2: for 1HZ |
|||
| A96-1 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
No. 3 CAN junction connector*1 ·
No. 11 CAN junction connector*2 |
| A96-12 (CANL) - J45-4 (CG) | |||
| A96-3 (CANH) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction terminal |
| A96-14 (CANL) - J45-4 (CG) | |||
| *a | Front view of wire harness connector
(to No. 73 Junction Connector) |
| *b | Front view of DLC3 |
| *c | ·
to No. 3 CAN Junction Connector (except 1HZ) ·
to No. 11 CAN Junction Connector (for 1HZ) |
| *d | to No. 1 CAN Junction Terminal |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) (except 1HZ) | B |
| NG (No. 11 CAN junction connector CAN main wire) (for 1HZ) | C |
| NG (ECU or sensor CAN wires) | D |
A
B
C
D
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-22 (CA2H) - J45-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| J51-7 (CA2L) - J45-4 (CG) |
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG