28100
1.INSPECT STARTER ASSEMBLY
Each of the following tests must be performed within 3 to 5 seconds to prevent the coil from burning out.
Use a thick cable for carrying a large electric current.
| *a | Terminal C | *b | Terminal 50 |
| *c | Terminal 30 | - | - |
Perform operation test without load.
Using a vise and aluminum protection plates, fix the starter assembly.
Connect the battery and an ammeter to the starter with terminal 30 disconnected, as shown in the illustration.
Do not connect terminal 50 to the battery.
| *a | Terminal 50 | *b | Terminal 30 |
| *c | Body | - | - |
Connect terminal 30 and terminal 50 to the battery and check that the starter rotates smoothly and steadily while the pinion gear is moving outward.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, repair or replace the starter assembly. |
||
| Battery - Terminal 30 | 11 V | 200 A or less |
28160
2.INSPECT STARTER ARMATURE ASSEMBLY
Check the commutator for open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Segment - Segment | Always | Below 1 Ω |
|
If the result is not as specified, replace the starter armature assembly. |
|
| *a | Segment |
Check the commutator for ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Commutator - Armature coil core | Always | 10 kΩ or higher |
|
If the result is not as specified, replace the starter armature assembly. |
|
| *a | Commutator |
| *b | Armature Coil Core |
Check that the commutator is not dirty or burnt.
If dirty or burnt, restore it with sandpaper (No. 400) or replace the starter armature assembly.
Using a vernier caliper, measure the commutator diameter.
36.0 mm (1.42 in.)
35.0 mm (1.38 in.)
If the diameter is less than the minimum, replace the starter armature assembly.
Using a vernier caliper, measure the undercut depth of the commutator.
0.7 mm (0.0276 in.)
0.2 mm (0.00787 in.)
If the undercut depth is less than the minimum, correct it with a hacksaw blade.
Check that the 2 bearings rotate smoothly.
If necessary, replace the starter armature assembly.
Inspect the commutator for circle runout.
Place the starter armature assembly on V-blocks.
Using a dial gauge, measure the circle runout.
0.05 mm (0.00197 in.)
If the circle runout is greater than the maximum, replace the starter armature assembly.
28120
3.INSPECT STARTER YOKE ASSEMBLY
Check the field coil for open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal C - Brush | Always | Below 1Ω |
|
If the result is not as specified, replace the starter yoke assembly. |
|
| *a | Brush |
| *b | Terminal C |
Check the field coil for ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Brush - Starter yoke body | Always | 10 kΩ or higher |
|
If the result is not as specified, replace the starter yoke assembly. |
|
| *a | Brush |
| *b | Starter Yoke Body |
28140
4.INSPECT STARTER BRUSH HOLDER ASSEMBLY
Using a vernier caliper, measure the starter brush length.
21.0 mm (0.827 in.)
12.0 mm (0.472 in.)
|
If the length is less than the minimum, replace the starter brush holder assembly and the starter yoke assembly. |
|
| *a | Length |
Replace all 4 starter brushes at the same time.
28140
5.INSPECT STARTER BRUSH HOLDER ASSEMBLY
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the starter brush holder assembly. |
||
| Positive brush holder - Negative brush holder | Always | 10 kΩ or higher |
Using a pull scale, measure the installed load of the spring at the exact moment the starter brush spring separates from the starter brush.
36 N (3.6 kgf, 8.0 lbf)
12.4 N (1.3 kgf, 2.8 lbf)
|
If the installed load is less than the minimum, replace the starter brush spring. |
|
| *a | Brush |
| *b | Brush Spring |
28011
6.INSPECT STARTER CLUTCH SUB-ASSEMBLY
Check the starter clutch sub-assembly operation.
| *a | Lock |
| *b | Free |
Hold the clutch and bearing with one hand and turn the shaft with the other.
Check that the inner sleeve turns easily in the "free" direction but cannot turn in the "lock" direction as shown in the illustration.
If the starter clutch sub-assembly does not operate as specified, replace the starter clutch sub-assembly.
28150
7.INSPECT MAGNET STARTER SWITCH ASSEMBLY
Check the pull-in coil for open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Terminal C | Always | Below 1.0 Ω |
|
If the result is not as specified, replace the magnet starter switch assembly. |
|
| *a | Terminal 50 |
| *b | Terminal C |
Check the holding coil for open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Magnet Starter Switch Body | Always | Below 2.0 Ω |
|
If the result is not as specified, replace the magnet starter switch assembly. |
|
| *a | Terminal 50 |
| *b | Magnet Starter Switch Body |