Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR (for 1HZ)
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0498911 COMPRESSOR(for 1HZ) A

AIR CONDITIONING  COMPRESSOR(for 1HZ)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNETIC CLUTCH ASSEMBLY

a.
I103030C01
2.021,0 2.26,0.188 0.24,0.188 10 false *a 0.844,0.24 1.146,0.458 0.302,0.219 10 false *b 0.646,1.531 0.948,1.75 0.302,0.219 10 false *b 1.219,1.74 1.521,1.958 0.302,0.219 10 false *b
*a Screw
*b Bolt


Install the magnetic clutch starter with the 3 bolts.

Torque:

7.9 N*m (81 kgf*cm, 70 in.*lbf)



b.

Install the ground wire with the screw.


c.
E471506

Using a snap ring expander, install the magnetic clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.



d.

Install the magnetic clutch washers and magnet clutch hub.

NOTICE:

Do not change the combination of the magnetic clutch washers used before disassembly.



e.
E471507C01
0.688,1 0.927,0.948 false 0.5,0.938 1.104,1.167 0.604,0.229 10 false *a
*a SST


Using SST, secure the magnetic clutch hub and install the bolt.

SST
09985-00030  

Torque:

22.6 N*m (230 kgf*cm, 17 ft.*lbf)


NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and clutch hub.



Hide 88410 2.INSPECT MAGNETIC CLUTCH CLEARANCE

a.
E471508C01
1.49,2.792 1.667,3.021 true 0.49,0.802 0.833,0.802 true 0.906,0.729 1.271,0.958 0.365,0.229 10 false 1 2.958,0.969 3.323,1.198 0.365,0.229 10 false *b 1.615,3.031 1.979,3.26 0.365,0.229 10 false *1 0.292,0.198 0.656,0.427 0.365,0.229 10 false *a 0.146,0.708 0.604,0.906 0.458,0.198 10 false MG+
*1 Magnet Clutch Hub
*a Component without harness connected
(Compressor And Magnetic Clutch)
*b Battery


Clamp the compressor in a vise.


b.

Set the dial indicator to the magnetic clutch hub.


c.

Connect the positive battery lead to terminal 1 (MG+) of the magnetic clutch connector and the negative lead to the ground wire. Turn the magnetic clutch on and off and measure the clearance.

Standard clearance:

0.6 to 1.0 mm (0.0237 to 0.0393 in.)


If the measured value is not within the standard clearance, remove the magnetic clutch hub and adjust the clearance using a magnetic clutch washer or combination of washers.

NOTICE:

Adjustment should be performed with 3 or less magnetic clutch washers.



d.

Remove the compressor from the vise.


Hide 88688K 3.INSTALL COOLER COMPRESSOR BRACKET

a.
E471502

Install the bracket with the bolt.


b.

Connect the connector clamp.