2011-2016 FJ Cruiser · Service Manual CRUISE CONTROL SYSTEM

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operated in the directions of the arrows and turns off when it is released. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

B133364E05

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
E107091E05
  1. Connect a intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. According to the display on tester, read the "Data List".


ECM (Cruise Control System):
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
Main SW M-CPU
Main switch signal (Main CPU) / ON or OFF
ON: Main switch ON
OFF: Main switch OFF
-
Cancel Switch
CANCEL switch signal / ON or OFF
ON: CANCEL switch ON
OFF: CANCEL switch OFF
-
SET/COAST Switch
-SET (SET/COAST) switch signal / ON or OFF
ON: -SET switch is ON
OFF: -SET switch is OFF
-
RES/ACC Switch
+RES (RES/ACC) switch signal / ON or OFF
ON: +RES switch is ON
OFF: +RES switch is OFF
-

OK:
When the cruise control main switch is operated, the display changes as shown above.

Result: 
Result
Proceed to
OK
A
NG (All items are defective)
B
NG (1 to 5 items are defective)
C


A
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
B


2. INSPECT CRUISE CONTROL MAIN SWITCH

  1. I045145E02
    Remove the cruise control main switch.

  1. Measure the resistance.

Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 3
cruise control switch neutral
10 kΩ or higher
cruise control switch ON
Below 1 Ω
cruise control switch OFF
10 kΩ or higher
+/RES
216 to 264 Ω
-/SET
567 to 693 Ω
CANCEL
1,386 to 1,694 Ω

  1. Reinstall the cruise control main switch.



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)

  1. B133362E01
    Disconnect the spiral cable side connector.

  1. Disconnect the cruise control main switch side connector.

  1. Measure the resistance.

Standard resistance:
Tester Connection
Specified Condition
Terminal 1 (ECC) main switch side - Terminal 4 (ECC) spiral cable side
Below 1 Ω
Terminal 3 (CCS) main switch side - Terminal 5 (CCS) spiral cable side
Below 1 Ω

  1. Reconnect the spiral cable side connector.

  1. Reconnect the cruise control main switch side connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SPIRAL CABLE
B133361E01

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets. (Click here)

  1. Remove the spiral cable.

  1. Measure the resistance.

Standard resistance:
Tester Connection
Specified Condition
Terminal 5 (CCS) main switch side - CCS (E17-5)
Below 1 Ω
Terminal 4 (ECC) main switch side - ECC (E17-4)
Below 1 Ω

HINT:
The spiral cable makes a maximum of approximately 5 rotations.

  1. Reinstall the spiral cable.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
  1. Disconnect the E81 ECM connector.

  1. Disconnect the E17 spiral cable (vehicle side) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E81-11 (CCS) - E17-5 (CCS)
    Below 1 Ω
    E81-11 (CCS) or E17-5 (CCS) - Body ground
    10 kΩ or higher
    E17-4 (ECC) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the spiral cable (vehicle side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Cruise Control Switch Circuit (Dec 2007 – Jul 2009)Cruise Control Switch Circuit (from Nov 2010) →