2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

  1. A226975E01
    Install a new gasket to the intake air surge tank assembly.
    Text in Illustration 
    *a
    Recess
    *b
    New Gasket

  1. Install the throttle with motor body assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the throttle body connector.

  1. A226865E01
    Connect the No. 4 water by-pass hose.
    Text in Illustration 
    *a
    RH
    *b
    Rear
    *c
    Top
    *d
    Matchmark

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the No. 5 water by-pass hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.


2. INSTALL AIR CLEANER HOSE ASSEMBLY

  1. A226974E01
    Install the air cleaner hose assembly with the 2 hose clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    Text in Illustration 
    *a
    Protrusion
    *b
    Groove
    *c
    Top
    *d
    RH
    *e
    Front
    *f
    Paint mark of the hose

  1. Install the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose and ventilation hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Engage the wire harness clamp.


3. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Remove the vinyl hose from the radiator drain cock of the radiator assembly.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the engine coolant level. If the engine coolant level is low, add engine coolant.

  1. A220212E03
    Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the radiator reserve tank cap sub-assembly.

  1. Install the radiator cap sub-assembly.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3

  1. Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator assembly if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap sub-assembly.*4

  1. Set the air conditioning as follows.*5

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator assembly and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
    2. Do not start the engine when there is no engine coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough engine coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7

    CAUTION:
    Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8

  1. A220212E03
    If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.
    If the engine coolant level is below the Full line, repeat steps *4 through *8.
    If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the service hole cover to the engine under cover.


4. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. A220211E01
    Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester


5. INSTALL V-BANK COVER
  1. Engage the 2 V-bank cover hooks to the bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.


6. PERFORM INITIALIZATION

NOTICE:
  1. Be sure to perform this procedure after reassembling the throttle body or removing and reinstalling any throttle body component.
  2. Perform the following procedure after replacing the ECM, throttle body or any throttle body components. The following procedure should also be performed if the throttle body is cleaned.
  3. Be sure to perform this procedure after replacing the ECM and reconnecting the battery cable.

  1. Disconnect the cable from the negative (-) battery terminal. Wait at least 60 seconds and reconnect the cable.

  1. Turn the ignition switch to ON without operating the accelerator pedal.

    NOTICE:
    If the accelerator pedal is operated, perform the above steps again.

  1. Connect the intelligent tester to the DLC3 and clear the DTCs (Click here).

  1. Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

    Standard:
    Condition
    Engine Idle Speed
    A/C switched off
    580 to 680 rpm

    NOTICE:
    1. Be sure to perform this step with all accessories off.
    2. Make sure that the shift lever is in neutral.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

  1. Perform a road test and confirm that there are no abnormalities.

← INSTALLATION (Aug 2009 – Jul 2013)INSTALLATION (from Aug 2014) →