2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel pressure system (Click here).

  1. Using a voltmeter, measure the battery voltage.

    Standard voltage:
    11 to 14 V

  1. Disconnect the negative battery terminal.

  1. Disengage the fuel pipe clamp.

  1. Disconnect the fuel pipe No. 1.

  1. A065093E02
    Install SST and the fuel tube connector onto the vehicle.

  1. Wipe off any spilt gasoline.

  1. Connect the cable to the negative battery terminal.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the intelligent tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control / ON.

  1. Measure the fuel pressure.

    Standard:
    281 to 287 kPa (2.87 to 2.93 kgf/cm2, 40.8 to 41.7 psi)

    1. If the fuel pressure is greater than the standard value, replace the fuel pump.
    1. If the fuel pressure is less than the standard value, check the connection between the fuel hose and fuel pump.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control / OFF.

  1. Check that the fuel pressure does not change for 5 minutes.

    Standard:
    147 kPa (1.5 kgf/cm2, 21 psi)

    If the result is not as specified, check the fuel pump and fuel injector.

  1. Disconnect the intelligent tester from the DLC3.

  1. Disconnect the cable from the battery negative terminal.

  1. Remove SST and the fuel tube connector while being careful to prevent gasoline splashes.

  1. Connect the fuel tube.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


4. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


5. REMOVE REAR SEAT CUSHION ASSEMBLY LH

  1. B130718
    Remove the 2 bolts and the rear seat cushion.


6. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. A129907
    Pull back the floor carpet.

  1. Remove the center floor silencer pad LH.

  1. A129904
    Remove the 3 screws from the center floor.

  1. A129908
    Disconnect the connector.


7. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A075955
    Loosen the clamp bolt and disconnect the fuel tank to filler pipe hose.


8. DISCONNECT FUEL CUT-OFF TUBE

  1. A226916E01
    Turn the retainer to disengage the lock claws and pull out the fuel cut off tube.
    Text in Illustration 
    *1
    Retainer
    *2
    O-Ring
    *3
    Fuel Pipe
    *4
    Nylon Tube
    V100135
    Turn
    V100136
    Pull

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube.
    4. To protect the tube, cover it with a vinyl bag after disconnecting it.
    5. When the connector and the pipe are stuck, turn the retainer carefully to free and then disconnect the fuel tank tube.


9. DISCONNECT FUEL TANK BREATHER TUBE

  1. A226916E01
    Turn the retainer to disengage the lock claws and pull out the fuel cut off tube.
    Text in Illustration 
    *1
    Retainer
    *2
    O-Ring
    *3
    Fuel Pipe
    *4
    Nylon Tube
    V100135
    Turn
    V100136
    Pull

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube.
    4. To protect the tube, cover it with a vinyl bag after disconnecting it.
    5. When the connector and the pipe are stuck, turn the retainer carefully to free and then disconnect the fuel tank tube.


10. REMOVE NO.1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Automatic Transmission)

  1. A137217
    Remove the 2 nuts and the fuel tank protector bracket.

  1. A129913
    Remove the 4 nuts and the fuel tank protector.


11. REMOVE NO.1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Manual Transmission)

  1. A138100
    Remove the nut and the fuel tank protector bracket.

  1. A129913
    Remove the 4 nuts and the fuel tank protector.


12. DISCONNECT FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE

  1. A226908E01
    Pinch the retainer to disengage the lock claws and pull out the fuel tank return tube.
    Text in Illustration 
    *1
    Retainer
    *2
    O-Ring
    *a
    Lock
    *b
    Unlock

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube.
    4. To protect the tube, cover it with a vinyl bag after disconnecting it.
    5. When the connector and the pipe are stuck, turn the retainer carefully to disconnect them.


13. REMOVE FUEL TANK ASSEMBLY
  1. Hold the fuel tank using a mission jack.

  1. A129914
    Remove the 2 fuel tank bands.

    1. Remove the 2 bolts.

    2. Remove the 2 clips and 2 pins, then remove the 2 fuel tank bands.


14. REMOVE FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE

  1. A172198E02
    Remove the 2 joint clips, and pull out the 2 fuel tank tubes.
    Text in Illustration 
    *1
    O-Ring
    V100135
    Pull

    NOTICE:
    1. Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
    2. Do not use any tools in this work.
    3. Do not bend or twist the nylon tube by force.
    4. After disconnecting, cover the fuel tube joint with a vinyl bag.
    5. When the fuel tube joint and fuel suction plate are stuck, turn the fuel tank main tube carefully to free and then disconnect it. Likewise, disconnect the fuel tank return tube.


15. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NOTICE:
Protect the connector and tube joint with masking tape or equivalent to prevent any foreign matter from sticking to them. Clean any dirt and foreign matter from the fuel suction tube assembly before removing.

  1. A076683E01
    Using a SST, loosen the retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Align the tips of the SST with the ribs on the retainer.

  1. Remove the retainer.

  1. Pull the fuel pump assembly out of the fuel tank.

    NOTICE:
    Do not bend the arm of the sender gauge.

  1. A172212
    Remove the gasket from the fuel tank.


16. REMOVE FUEL SENDER GAUGE ASSEMBLY

E127931
  1. Disconnect the fuel sender gauge connector.

  1. E127932
    Unlock the fuel sender gauge, and slide and remove it.

← COMPONENTS (from Aug 2009)REMOVAL (from Aug 2009) →