2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

ON-VEHICLE INSPECTION

Inspection · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


INSPECT SPEEDOMETER
  1. Check the operation.

    1. Using a speedometer tester, inspect the speedometer and confirm that the speedometer readings are within the acceptable range. Also check the odometer operation.

      Reference:
      km/h:
      Standard Indication
      Acceptable Range
      20 km/h
      17.5 to 21.5 km/h
      40 km/h
      38 to 42 km/h
      60 km/h
      58 to 63 km/h
      80 km/h
      78 to 84 km/h
      100 km/h
      98.5 to 104.5 km/h
      120 km/h
      119 to 125 km/h
      140 km/h
      139 to 146 km/h
      160 km/h
      159 to 167 km/h
      180 km/h
      179 to 188 km/h
      200 km/h
      199 to 209 km/h
      mph:
      Standard Indication
      Acceptable Range
      20 mph
      19 to 22 mph
      40 mph
      39 to 42.5 mph
      60 mph
      59.5 to 63.5 mph
      80 mph
      79.5 to 84 mph
      100 mph
      100 to 105 mph
      120 mph
      121 to 126.5 mph

      NOTICE:
      Tire wear and excessively high or low tire pressure affect speedometer indications.

    2. Check the deflection of the speedometer indicator.

      Reference:
      Below 0.5 km/h (0.3 mph)


INSPECT SPEED SENSOR

E153140E01
  1. Check the output signal waveform.

    1. Remove the combination meter assembly, but do not disconnect the connector.

    2. Connect an oscilloscope to terminal E13-4 and to the body ground.

    3. Start the engine.

    4. Check the signal waveform according to the conditions in the table below.

      Item
      Contents
      Terminal Connection
      E13-4 (SE) - Body Ground
      Tool Setting
      5V / DIV, 20ms / DIV
      Condition
      Driving at approximately 20km / h (12mph)

      OK:
      As shown in the illustration.

      NOTICE:
      As the vehicle speed increases, the cycle of the signal waveform narrows.

    5. Reinstall the combination meter assembly.


INSPECT TACHOMETER
  1. Check the operation.

    1. Connect the tune-up test tachometer and start the engine.

      NOTICE:
      1. Reversing the connection of the tachometer will damage the transistors and the insides of the diodes.
      2. When removing or installing the tachometer, be careful not to drop or strike it.

    2. Compare the result of the test with the standard indication.
      DC 13.5 V, at 25°C (77°F)

      Reference:
      Standard Indication (USA) (RPM)
      Standard Indication (CANADA) (r/min)
      Data in ( ) are for reference
      Acceptable Range (USA) (RPM)
      Acceptable Range (CANADA) (r/min)
      Data in ( ) are for reference
      700
      630 to 770
      1,000
      (900 to 1,100)
      2,000
      (1,850 to 2,150)
      3,000
      2,800 to 3,200
      4,000
      (3,800 to 4,200)
      5,000
      4,800 to 5,100
      (6,000)
      (5,750 to 6,250)


INSPECT FUEL RECEIVER GAUGE

  1. E153141E01
    Disconnect the L5 fuel sender gauge connector.

  1. Check the fuel receiver gauge operation when the ignition switch is turned to the ON position.

    OK:
    Needle position is on EMPTY.

  1. Connect terminals 2 and 3 on the wire harness side connector of the fuel sender gauge.

  1. Check the fuel receiver gauge operation when the ignition switch is turned from OFF to ON.

    OK:
    Needle position is on FULL.

  1. Reconnect the fuel sender gauge connector.


INSPECT FUEL LEVEL WARNING LIGHT
  1. Disconnect the fuel sender gauge connector.

  1. Turn the ignition switch to the ON position, then check that the fuel level needle indicates EMPTY and the fuel level warning light comes on.

    OK:
    Fuel level warning light comes on.

  1. Reconnect the fuel sender gauge connector.


INSPECT ENGINE OIL PRESSURE WARNING LIGHT
  1. Disconnect the engine oil pressure switch connector.

  1. Turn the ignition switch to the ON position.

  1. Ground the terminal of the wire harness side connector, then check the engine oil pressure warning light.

    OK:
    Engine oil pressure warning light illuminates.

  1. Reconnect the engine oil pressure switch connector.


INSPECT BRAKE WARNING LIGHT
  1. Inspect the parking brake warning light.

    1. Disconnect the parking brake switch connector.

    2. Turn the ignition switch to the ON position.

    3. Ground the terminal of the wire harness side connector, then check the parking brake warning light.

      OK:
      Brake warning light illuminates.

    4. Reconnect the parking brake switch connector.

  1. Inspect the brake fluid level warning light.

    1. Disconnect the brake fluid level warning switch connector.

    2. Turn the ignition switch to the ON position.

    3. Connect a terminal to the other terminal of the wire harness side connector, then check the brake fluid level warning switch.

      OK:
      Brake warning light illuminates.

    4. Reconnect the brake fluid level warning switch connector.


INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Float inside reservoir tank is in high position (switch OFF): 10 k Ω or higher

  1. Use a siphon or a similar tool to drain fluid out of the reservoir tank.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Float inside reservoir tank is in low position (switch ON): Below 1 Ω

  1. Pour the fluid back into the reservoir tank.

  1. Reconnect the brake fluid level warning switch connector.

  1. Reinstall the reservoir tank cap and strainer.

← DIAGNOSTIC TROUBLE CODE CHART (from Nov 2012)ON-VEHICLE INSPECTION (from Nov 2010) →