2011-2016 FJ Cruiser · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


1. PRECAUTION
(Click here)

2. INSTALL STEERING ANGLE SENSOR

C133075
  1. Install the steering angle sensor.

  1. C133074
    Connect the harness and steering angle sensor connector.

  1. Connect the steering sensor connector.


3. INSTALL SPIRAL CABLE
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch in the neutral position.

    NOTICE:
    If it is not in the neutral position, the pin of the turn signal switch may snap.

  1. C128206
    Install the spiral cable with the 4 screws.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. C141564E01
    Connect the connectors to the spiral cable.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


4. INSTALL UPPER STEERING COLUMN COVER

  1. C133808
    Engage the claw and install the upper steering column cover.


5. INSTALL LOWER STEERING COLUMN COVER

  1. C133807
    Engage the 2 claws.

  1. Install the lower steering column cover with the 3 screws.


6. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is turned to OFF.

  1. Check that the negative (-) battery terminal is disconnected.

    CAUTION:
    After removing the terminal, wait for at least 90 seconds before starting the operation.

  1. C128207
    Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with the airbag wire harness or connector.

  1. C128208E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with the airbag wire harness or connector.

    HINT:
    The spiral cable will rotate approximately 2.5 turns both ways from the center.


7. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


8. INSPECT STEERING WHEEL CENTER POINT

9. INSTALL STEERING PAD

  1. C128255E01
    Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it from moving upward.


10. INSTALL STEERING WHEEL COVER LOWER NO.2

  1. C128196
    Install steering wheel cover lower No.2.


11. INSTALL STEERING WHEEL COVER LOWER NO.3

  1. C128195
    Install steering wheel cover lower No.3.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


13. INSPECT STEERING PAD

  1. C128192
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


14. PERFORM INITIALIZATION
(Click here)

15. INSPECT SRS WARNING LIGHT
(Click here)
← INSPECTION (from Jul 2007)INSTALLATION (Nov 2010 – Jul 2012) →