2011-2016 FJ Cruiser · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012


1. CLEAN WINDSHIELD GLASS

B073128E01
  1. Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

  1. Clean the outer circumference of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.


2. CLEAN VEHICLE BODY

  1. B073084E14
    Clean and shape the contact surface of the vehicle body.
    Text in Illustration 
    *1
    Adhesive

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.


3. INSTALL WINDSHIELD GLASS STOPPER NO. 1

  1. B140026
    Install 2 new stoppers onto the vehicle body, as shown in the illustration.


4. INSTALL WINDSHIELD GLASS STOPPER NO. 2

B139393E02
Text in Illustration 
*a
Ceramic Notch
  1. Apply Primer G to the installation parts of the stoppers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new stoppers onto the windshield glass, as shown in the illustration.

    Specification:
    Area
    Measurement
    A
    40 mm (1.57 in.)
    B
    7.8 mm (0.307 in.)
    C
    12.5 mm (0.482 in.)


5. INSTALL WINDSHIELD OUTSIDE MOULDING LH

B139394E02
Text in Illustration 
*A
w/o Rain G
*B
w/ Rain G
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Do not coat the adhesive with Primer G.
    3. Throw away any leftover Primer G.

  1. Install the moulding onto the windshield glass, as shown in the illustration.


6. INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.


7. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the installation parts of new dams.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 3 new dams by applying double-sided tape all the way around the windshield glass except where the stoppers are installed, as shown in the illustration.

    B139395E02

    Text in Illustration 
    *a
    Ceramic Notch
    -
    -

    Specification:
    Area
    Measurement
    a
    7.0 mm (0.276 in.)
    b
    15.8 mm (0.622 in.)


8. INSTALL WINDSHIELD GLASS

  1. B139396E02
    Position the windshield glass.
    Text in Illustration 
    *1
    Stopper
    *a
    Matchmarks

    1. Using suction cups, place the windshield glass in the correct position.

    2. Check that the entire contact surface of the windshield glass rim is perfectly even.

    3. Place matchmarks on the windshield glass and vehicle body.

      NOTICE:
      Check that the stoppers are correctly attached to the vehicle body.

      HINT:
      When reusing a windshield glass, check and correct the matchmark positions.

    4. Using suction cups, remove the windshield glass.

  1. B271492E01
    Using a brush, apply Primer M to the exposed part of the vehicle body.
    Text in Illustration 
    *1
    Primer M
    *2
    Adhesive
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

  1. Using a brush or sponge, apply Primer G to the edge of the windshield glass and the contact surface.

    B139398E01

    Specification:
    Area
    Measurement
    a
    7.8 mm (0.307 in.)
    b
    7.8 mm (0.307 in.)
    c
    7.0 mm (0.276 in.)
    d
    8.0 mm (0.315 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or the equivalent


    1. B106205E05
      Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the times indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the windshield glass, as shown in the illustration.

      B139399E01

      Specification:
      Area
      Measurement
      a
      12 mm (0.472 in.)
      b
      8 mm (0.315 in.)
      c
      3 mm (0.118 in.)
      d
      3 mm (0.118 in.)
      e
      3 mm (0.118 in.)
      f
      11.8 mm (0.465 in.)

  1. B139396E02
    Install the windshield glass onto the vehicle body.
    Text in Illustration 
    *1
    Stopper
    *a
    Matchmarks

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned. Gently press it in along the rim.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the stoppers are attached to the vehicle body correctly.
      3. Check that there is a small gap between the vehicle body and the windshield glass.

    2. Gently press the front surface of the windshield glass to ensure that the windshield glass is securely fitted to the vehicle body.

    3. B112214
      Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the windshield glass rim.

      NOTICE:
      Do not drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


9. INSTALL WINDSHIELD OUTSIDE LOWER MOULDING
  1. Engage the 6 claws and install the windshield outside lower moulding.


10. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leakage with auto glass sealer.


11. INSTALL NO. 2 ROOF SIDE GARNISH PROTECTOR
  1. Install a new roof side garnish protector with the 4 clips.


12. INSTALL NO. 1 ROOF SIDE GARNISH PROTECTOR

HINT:
Use the same procedure as for the No. 2 roof side garnish protector (Click here).


13. INSTALL FRONT PILLAR OUTER GARNISH LH
  1. Engage the 5 clips and install the front pillar outer garnish.

  1. Tighten the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


14. INSTALL FRONT PILLAR OUTER GARNISH RH

HINT:
Use the same procedure as for the LH side (Click here).


15. INSTALL ROOF DRIP SIDE FINISH MOULDING RETAINER

HINT:
Use the same procedure to install all the roof drip side finish moulding retainers.

  1. Install the roof drip side finish moulding retainer.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


16. INSTALL WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY
  1. Clean the windshield glass.

    1. Using a scraper, remove the adhesive from the windshield glass.

    2. Clean the outer circumference of the windshield glass with a non-residue solvent.

      NOTICE:
      Do not touch the windshield glass surface after cleaning it.

  1. Using a brush or sponge, apply Primer G to the contact surface.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or the equivalent


    1. Cut the tip off the cartridge nozzle.

      HINT:
      After cutting off the tip, use all adhesive within the times indicated in the table below.
      Usage time frame: 
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to a new windshield outside upper moulding, as shown in the illustration.

      B267743E01

      Specification: 
      Area
      Measurement
      *1
      10 mm (0.394 in.) or more
      *2
      8 mm (0.315 in.) or more
      *3
      3.5 to 9.5 mm (0.138 to 0.374 in.)

  1. Engage the 4 claws and the 2 clips and install a new windshield outside upper moulding.

    NOTICE:
    Do not drive the vehicle within the time indicated in the table below.
    Minimum time: 
    Temperature
    Minimum time prior to driving vehicle
    35°C (95°F)
    1 hour 30 minutes
    20°C (68°F)
    5 hour
    5°C (41°F)
    24 hours

  1. Remove the protective tape.


17. INSTALL ROOF HEADLINING

18. INSTALL ROOM LIGHT ASSEMBLY
  1. Install room light bulb No. 1.

  1. B138414
    Engage the 4 claws and install the room light switch base.

  1. Install the roof wire into the claw of the room light.

  1. E114445
    Engage the 4 claws and install the room light.

  1. B124366
    Engage the 4 claws and install the 2 covers.

  1. E114446
    Engage the 4 claws and install the room light lens.


19. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
(Click here)

20. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
(Click here)

21. INSTALL VISOR HOLDER

B130631E05

HINT:
Use the same procedure for both sides.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120°and install the visor holder.


22. INSTALL VISOR ASSEMBLY RH
  1. Install the visor with the 2 screws.

  1. Install the visor support shaft into the visor holder.


23. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


24. INSTALL FRONT PILLAR GARNISH RH
  1. w/ Assist Grip:

    1. Engage the guide and the 2 clips and install the front pillar garnish.

  1. w/o Assist Grip:

    1. Engage the guide and the 2 clips and install the front pillar garnish.

    2. Tighten the bolt.

    3. B271491
      Engage the claw and close the cover.


25. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


26. INSTALL VISOR SUB-ASSEMBLY RH
  1. Engage the 2 claws and install the visor sub-assembly.


27. INSTALL VISOR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


28. INSTALL ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure to install all the assist grips.

  1. Install the assist grip with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


29. INSTALL ASSIST GRIP PLUG

B175649E04

HINT:
Use the same procedure to install all the assist grip plugs.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Engage the 2 claws and install the assist grip plug.


30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130604E03
    Align the locating marks with the paint marks first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Text in Illustration 
    *a
    Locating Mark
    *b
    Paint Mark

    Paint mark:
    Area
    Color
    RH side
    White
    LH side
    Red


31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


32. INSTALL ROOF SIDE RAIL GARNISH RH
  1. Engage the guide and the claws and install the roof side rail garnish.

  1. Tighten the 2 bolts.


33. INSTALL ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.


34. INSTALL ROOF SIDE INNER GARNISH COVER RH

B130601

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the roof side inner garnish cover.


35. INSTALL ROOF SIDE INNER GARNISH COVER LH

HINT:
Use the same procedure as for the RH side.


36. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the 2 claws and install the cowl side trim board.

  1. Install the clip.


37. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


38. INSTALL FOOTREST CLIP (for LHD)

B130588

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the footrest clip.


39. INSTALL FRONT FLOOR FOOTREST (for LHD)

  1. B130589
    Engage the 2 studs and install the front floor footrest.


40. INSTALL ACCESS DOOR SCUFF PLATE RH
  1. Engage the 6 claws and install the access door scuff plate.


41. INSTALL ACCESS DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


42. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 14 claws and install the door scuff plate.


43. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


44. INSTALL COWL TOP VENTILATOR LOUVER LH

  1. E127865
    Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.


45. INSTALL COWL TOP VENTILATOR LOUVER RH

  1. E127864
    Install the cowl top ventilator louver RH with the 3 clips and the claw.

  1. Install the hood to cowl top seal with the clip.


46. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E127863
    Install the cowl top ventilator louver sub-assembly with the 7 clips.


47. INSTALL FRONT FENDER SIDE PANEL UPPER LH
  1. Install the 4 new clips on the front fender side panel upper LH.

  1. B210065
    Engage the 4 clips and install the front fender side panel upper LH.


48. INSTALL FRONT FENDER SIDE PANEL UPPER RH
  1. Install the 4 new clips on the front fender side panel upper RH.

  1. B210064
    Engage the 4 clips and install the front fender side panel upper RH.


49. INSTALL ANTENNA ORNAMENT

  1. E127861E02
    Press in the antenna ornament in the direction shown in the illustration.


50. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

B138406E01
  1. Install the radio antenna pole by turning it in the direction of the arrow shown in the illustration.

    Torque:
    3.3 N*m{ 35 kgf*cm , 29 in.*lbf }

    NOTICE:
    Use a short wrench, tighten with your finger, not your hand.


51. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127876E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


52. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127875E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


53. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127874E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


54. INSTALL WINDSHIELD WIPER ARM COVER

  1. E127877E01
    Engage the claw and install the 3 front wiper arm cover.

← INSTALLATION (Jul 2007 – Oct 2010)INSTALLATION (Aug 2011 – Jul 2012) →