2011-2016 FJ Cruiser · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


1. CLEAN QUARTER WINDOW GLASS

  1. BO04421E01
    Clean the outer circumference of the glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Even if using a new glass, clean the glass with a non-residue solvent.


2. CLEAN VEHICLE BODY

  1. B073084E14
    Clean and shape the contact surface of the vehicle body.
    Text in Illustration 
    *1
    Adhesive

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.


3. INSTALL QUARTER WINDOW GLASS

  1. B271493E01
    Using a brush, apply Primer M to the exposed part of the vehicle body.
    Text in Illustration 
    *1
    Primer M
    *2
    Adhesive
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

  1. B139424E01
    Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    Specification:
    Area
    Measurement
    a
    20 mm (0.787 in.)
    b
    17.3 mm (0.681 in.)
    c
    26 mm (1.024 in.)
    d
    20 mm (0.787 in.)
    e
    20 mm (0.787 in.)
    f
    5 mm (0.197 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. B140014E01
    Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or the equivalent


    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      27.3 mm (1.075 in.)
      d
      8 mm (0.315 in.)
      e
      8 mm (0.315 in.)
      f
      10 mm (0.394 in.)
      g
      14 mm (0.551 in.)

  1. Install the quarter window glass onto the body.

    1. Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the pins are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.

    3. B112214
      Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the quarter window glass rim.

      NOTICE:
      Do not drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


4. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leakage with auto glass sealer.


5. INSTALL BACK DOOR HINGE PROTECTOR LH

  1. B266335
    Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Using a piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Remove the double-sided tape backing of the back door hinge protector LH.

  1. Engage the 3 guides and install a new back door hinge protector LH.

    NOTICE:
    Thoroughly press the back door hinge protector LH to ensure that it adheres.


6. INSTALL ROOF SIDE INNER GARNISH

HINT:
Use the same procedure as for the RH side.


7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Tighten the 3 screws.

  1. Tighten the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Tighten the 3 screws.


9. INSTALL REAR SEAT OUTER BELT ASSEMBLY

HINT:
Use the same procedure as for the RH side.


10. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the lap belt outer anchor cover.


11. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
  1. Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }

  1. Connect the connectors.


12. INSTALL SPEAKER MOUNTING COVER (w/ Woofer)
  1. Engage the 8 clips and 2 guides and install the speaker mounting cover.


13. INSTALL DECK SIDE GARNISH (w/ Woofer)
  1. Engage the 6 claws and install the deck side garnish.


14. INSTALL QUARTER TRIM POCKET (w/o Woofer)
  1. Engage the 6 claws and install the quarter trim pocket.


15. INSTALL SIDE TRIM COVER (w/o Woofer)
  1. Engage the 6 claws and the 2 guides and install the side trim cover.


16. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)
  1. Engage the 7 claws and install the quarter trim pocket tray.


17. INSTALL PACKAGE HOLDER NET HOOK

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }


18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:
Use the same procedure as for the RH side.


19. INSTALL REAR DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.


20. INSTALL FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.


21. INSTALL REAR FLOOR MAT ASSEMBLY
  1. Install the rear floor mat with the 2 clips.


22. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.


23. INSTALL REAR FLOOR MAT SUPPORT PLATE
  1. Engage the 11 claws and install the rear floor mat support plate.

  1. Tighten the 5 screws.


24. INSTALL REAR FLOOR BOARD
  1. Engage the clip and claw and install the rear floor board.

  1. B135074E05
    Install the luggage hold belt striker with the bolt.
    Text in Illustration 
    *1
    Guide
    *a
    for RH Side
    *b
    for LH Side

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.


25. INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)

  1. B130750E01
    Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.

  1. B135128E01
    Install the rear seat inner belt into the rear seatback holder.

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.


26. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH (for RH Side)

  1. B130749
    Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.


27. INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)

  1. B130721E01
    Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Install the rear center seat inner belt into the rear seatback holder.


28. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH (for LH Side)

  1. B130720
    Engage the 8 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.

← INSTALLATION (Jul 2007 – Oct 2010)INSTALLATION (from Aug 2012) →