2011-2016 FJ Cruiser · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


1. PRECAUTION

CAUTION:
Read "PRECAUTION" thoroughly before servicing (Click here).


2. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is turned to OFF.

  1. Check that the negative (-) battery terminal is disconnected.

    NOTICE:
    After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

  1. C128260
    Temporarily install the center airbag sensor assembly with the 3 bolts.

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, make sure that the SRS wiring does not interfere with any other parts and that it is not pinched between other parts.

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. C128259E01
    Connect the holder (with connectors) to the center airbag sensor assembly.

  1. Check that the water-proof sheet is properly set.


3. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
  1. Engage the 3 clips and 2 claws and install the instrument lower cover.

  1. Install the 2 <E> bolts and 2 clips.


4. INSTALL CONSOLE UPPER PANEL NO.1 GARNISH

  1. B271482
    Slide the console upper panel garnish toward the front of the vehicle and engage guide.

  1. Engage the claw and clip and install the console upper panel garnish.


5. INSTALL FRONT CONSOLE BOX
  1. Engage the 5 guides and install the front console box.

  1. Install the 4 <H> bolts.


6. INSTALL BOX BOTTOM MAT
  1. Install the box bottom mat.


7. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY
  1. Engage the 3 guides and 5 clips and install the console upper rear panel.


8. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY

  1. B271483
    Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 guides.

  1. Engage the 4 claws and install the parking brake hole cover.


9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B133894
    Install the shift lever knob.


10. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B133896
    Install the shift lever knob.


11. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY
  1. Connect the 3 connectors.

  1. Engage the 4 clips and install the integration control panel assembly.

  1. Install the 2 screws.


12. INSTALL INSTRUMENT PANEL GARNISH RH
  1. Engage the 3 clips and install the instrument panel garnish.

  1. Install the screw <G>.


13. INSTALL INSTRUMENT PANEL GARNISH LH
  1. Engage the 3 clips and install the instrument panel garnish.

  1. Install the screw <G>.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


15. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    HINT:
    Some systems need initialization after reconnecting the cable to the negative battery terminal.


16. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← INSTALLATION (Jul 2007 – Oct 2010)INSTALLATION (from Aug 2012) →