2011-2016 FJ Cruiser · Service Manual RESTRAINTS

DISPOSAL

Removal / installation · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures described below are for the LH side.
  3. When scrapping a vehicle equipped with the SRS or disposing of the front seat side airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with airbag deployment, contact the SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.

CAUTION:
  1. Never dispose of a front seat side airbag assembly that has an undeployed airbag.
  2. The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
  3. When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
  4. When deploying the airbag, perform the operation at least 10 m (33 ft) away from the airbag assembly.
  5. The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  6. Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.
  7. Do not apply water, etc. to a front seat side airbag assembly with a deployed airbag.
  8. Always wash your hands with water after completing the operation.


1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. B104819E01
    Check the function of SST (Click here).

  1. Precaution (Click here).

  1. Disconnect the cable from the negative battery terminal.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.

  1. Remove the 4 bolts from the front seat assembly (Click here).

    HINT:
    Keep the front seat assembly in the cabin.

  1. Install SST.

    1. C128282E01
      Disconnect the connector (yellow colored one) from the front seat side airbag assembly.

      NOTICE:
      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. C128241E01
      Connect the SST connector to the front seat side airbag assembly connector.
      SST
      09082-00700  
      09082-00750  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

    3. Install the front seat assembly with the 4 bolts (Click here).

    4. C110476E01
      Move SST at least 10 m (33 ft) away from the vehicle side window.

    5. Securing enough clearance for the SST wire harness in the side window, close all doors and windows of the vehicle.

      NOTICE:
      Take care not to damage the SST wire harness.

    6. Connect the red clip of the SST to the positive (+) battery terminal and the black clip of the SST to the negative (-) battery terminal.

  1. Deploy the airbag.

    1. Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.

    2. Press the SST activation switch and deploy the airbag.

      CAUTION:
      1. When deploying the airbag, make sure that no one is near the vehicle.
      2. The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
      3. Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.
      4. Do not apply water, etc. to a front seat side airbag assembly with a deployed airbag.
      5. Always wash your hands with water after completing the operation.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.


2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:
  1. When disposing of the front seat side airbag assembly, never use the customer's vehicle to deploy the airbag.
  2. Be sure to follow the procedure detailed below when deploying the airbag.

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. B104819E01
    Check the function of SST (Click here).

  1. Remove the front seat side airbag assembly (Click here).

    CAUTION:
    1. When removing the front seat side airbag assembly, work must be started 90 seconds after the ignition switch is turned to the "LOCK" position and the negative (-) terminal cable is disconnected from the battery.
    2. When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

  1. B104882E01
    Using a service-purpose wire harness for the vehicle, tie down the front seat side airbag assembly to the tire.
    Stripped wire harness section: 
    Area
    Measurement
    A
    1.25 mm2 or more (0.0019 in.2 or more)

    HINT:
    To calculate the area of the stripped wire harness section:
    Area = 3.14 x (Diameter)2 divided by 4

    CAUTION:
    If the wire harness is too thin or any other object is used to tie down the front seat side airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).


    1. C140809
      Install the front seat side airbag assembly with the 2 nuts.

    2. C140810
      Wind the wire harnesses around the stud bolts of the front seat side airbag assembly as shown in the illustration.

    3. C128234E01
      Position the front seat side airbag assembly inside the tire as shown in the illustration.
      Must exceed the following dimensions.
      Tire size: 
      Area
      Measurement
      Width
      185 mm (7.28 in.)
      Inner diameter
      360 mm (14.17 in.)

      CAUTION:
      1. Make sure that the wire harness is tight. If there is slack in the wire harnesses, the front seat side airbag assembly may become loose due to the shock when the airbag is deployed.
      2. Always tie down the front seat side airbag assembly with the airbag deployment direction facing inside the tire.

      NOTICE:
      The tire will be damaged by airbag deployment, so use waste tires.

  1. Install SST.

    1. C121170E03
      Connect the SST connector to the front seat side airbag assembly connector.
      SST
      09082-00750  

  1. C107074E02
    Place the tires.

    1. Place at least 2 tires under the tire to which the front seat side airbag assembly is tied.

    2. Place at least 2 tires over the tire to which the front seat side airbag assembly is tied. The top tire should have a disc wheel installed.

      NOTICE:
      Do not place the SST connector under the tire because it could be damaged.

    3. B105087
      Tie the tires together with 2 wire harnesses.

      CAUTION:
      Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

  1. Install SST.

    1. B105200E01
      Connect the SST connector.
      SST
      09082-00700  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

    2. Move SST at least 10 m (33 ft) away from the airbag tied down to the tires.

  1. Deploy the airbag.

    1. Connect the red clip of the SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    2. Check that no one is within a 10 m (33 ft) radius of the tire to which the front seat side airbag assembly is tied.

    3. Press the SST activation switch and deploy the airbag.

      CAUTION:
      When deploying the airbag, make sure that no one is near the tires.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.

  1. H000544E01
    Dispose of the front seat side airbag assembly.

    CAUTION:
    1. The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
    2. Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.
    3. Do not apply water, etc. to a front seat side airbag assembly with a deployed airbag.
    4. Always wash your hands with water after completing the operation.


    1. Remove the front seat side airbag assembly from the tire.

    2. Place the front seat side airbag assembly in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.

← DISPOSAL (Jul 2007 – Oct 2010)DISPOSAL (from Aug 2012) →