2011-2016 FJ Cruiser · Service Manual RESTRAINTS

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


COMBINATION METER ASSEMBLY
E125398E02
  1. Disconnect the E13 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-1 (B) - Body ground
    R - Body ground
    Battery
    Always
    11 to 14 V
    E13-2 (IG+) - Body ground
    R-L - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1 V → 11 to 14 V
    E13-21 (ES) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the combination meter assembly connector.

  4. Measure the voltage of the wire harness side connector.

    Standard voltage: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-7 (WRNP) - Body ground
    LG - Body ground
    Seat belt warning light signal (Front passenger side)
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is unfastened
    Alternating between 11 to 14 V and below 3 V
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is fastened
    Below 1 V
    E13-8 (L) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is unfastened (Front driver side)
    Below 1 V
    Ignition switch ON
    Front seat belt is fastened (Front driver side)
    11 to 14 V
    E13-10 (PBKL) - Body ground
    L-R - Body ground
    Front seat inner belt signal (Front passenger side)
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is unfastened
    Below 1 V
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is fastened
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


MAIN BODY ECU
B136051E04
B136052E04
  1. Disconnect the 1A, 1B and 1H main body ECU connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1B-4 (BECU) - Body ground
    W-R - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    1H-2 (GND1) - Body Ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1A-7 (GND2) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1F-8 (SIG) - Body ground
    B-R - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1 V → 11 to 14 V
    E6-13 (DBKL) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is unfastened (Front driver side)
    Below 1 V
    Ignition switch ON
    Front seat belt is fastened (Front driver side)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

← PROBLEM SYMPTOMS TABLE (from Nov 2010)TERMINALS OF ECU (from Nov 2010) →