Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).
HINT:
Use the same procedure for both the RH and LH sides.
1.
BOLTS, SCREWS AND NUTS TABLE
HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.
3.
DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
Start up the engine.
Switch A/C ON.
Turn the blower switch to ON.
Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.
Stop the engine.
Remove the caps from the service valves on the refrigerant line.
Connect the refrigerant recovery unit.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
NOTICE:
Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.
4.
DRAIN ENGINE COOLANT
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Remove the service hole cover from the engine under cover.
Install a vinyl hose onto the drain on the radiator side.
Text in Illustration
*1
Vinyl Hose
*2
Tape
Fix the vinyl hose with tape.
Text in Illustration
*1
Radiator Cap
*2
Reservoir Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
Loosen the radiator drain cock plug.
Remove the radiator cap and drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.
NOTICE:
If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of water pump may result.
5.
REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY
Remove the radio antenna pole by turning it in the direction of the arrow shown in the illustration.
6.
REMOVE WINDSHIELD WIPER ARM COVER
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 3 front wiper arm cover.
7.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
8.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)
HINT:
Use the same procedure as for the LH side.
9.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10.
REMOVE FRONT FENDER SIDE PANEL UPPER LH
Disengage the 4 clips and remove the front fender side panel upper LH.
Remove the 4 clips from the front fender side panel upper LH.
11.
REMOVE ANTENNA ORNAMENT
Pull out the antenna ornament vertically.
12.
REMOVE FRONT FENDER SIDE PANEL UPPER RH
Disengage the 4 clips and remove the front fender side panel upper RH.
Remove the 4 clips from the front fender side panel upper RH.
13.
REMOVE COWL TOP VENTILATOR LOUVER ASSEMBLY
Disengage the 7 clips and remove the cowl top ventilator louver sub-assembly.
14.
REMOVE COWL TOP VENTILATOR LOUVER RH
Disengage the clip and remove the hood to cowl top seal.
Remove the 3 clips and the claw, and remove the cowl top ventilator louver RH.
15.
REMOVE COWL TOP VENTILATOR LOUVER LH
Remove the 5 clips.
Disengage the 7 claws and remove the cowl top ventilator louver LH.
16.
DISCONNECT COOLER REFRIGERANT SUCTION PIPE A
Install SST onto the piping clamp.
SST
09870-00015
HINT:
Check the directions of the piping clamp and SST by referring to the illustration on the caution label.
Push down SST and release the clamp lock.
NOTICE:
Do not deform the tube when pushing SST.
Pull SST slightly, push the release lever, and then remove the piping clamp with SST.
Disconnect the suction pipe.
NOTICE:
Do not use any tools when disconnecting the pipe.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.
17.
DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
SST
09870-00025
HINT:
Disconnection procedure of the liquid pipe is the same as for the suction pipe.
18.
DISCONNECT HEATER WATER HOSE INLET
Using pliers, grip the claw of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.
19.
DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)
Using pliers, grip the claw of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.
20.
POSITION FRONT WHEELS FACING STRAIGHT AHEAD
21.
REMOVE LOWER NO. 3 STEERING WHEEL COVER
Using a thin-bladed screwdriver, remove steering wheel cover lower No.3.
HINT:
Tape up the screwdriver tip before use.
22.
REMOVE LOWER NO. 2 STEERING WHEEL COVER
Using a thin-bladed screwdriver, remove steering wheel cover lower No.2.
HINT:
Tape up the screwdriver tip before use.
23.
REMOVE STEERING PAD
Using "Torx" socket wrench (T30), loosen the 2 "Torx" screws until the groove along the screw circumference catches on the screw case.
Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand as shown in the illustration.
NOTICE:
When removing the steering pad, do not pull the airbag wire harness.
Disconnect the horn connector.
Disconnect the 2 connectors from the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Remove the steering pad.
24.
REMOVE STEERING WHEEL ASSEMBLY
Remove the steering wheel assembly set nut.
Place matchmarks on the steering wheel assembly and main shaft assembly.
Disengage the 5 clips and claw and remove the lower instrument panel finish panel.
56.
REMOVE LOWER INSTRUMENT PANEL LH
Remove the 4 <F> bolts and remove the lower instrument panel.
57.
REMOVE INSTRUMENT CLUSTER FINISH PANEL
Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.
Disconnect the connectors.
58.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws.
Disconnect the 2 connectors and clamp and remove the combination meter.
59.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.