2011-2016 FJ Cruiser · Service Manual DRIVE LINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jul 2007


TRANSFER SYSTEM

NOTICE:
  1. To shift from H2 to H4, reduce the vehicle's speed to less than 50 mph (80 km/h) and move the transfer shift lever.
  2. To shift from H4 to L4, stop the vehicle, move the shift lever to N and then move the transfer shift lever.
  3. To shift from L4 to H4, stop the vehicle, move the shift lever to N and then move the transfer shift lever.


CHECK H2 (2WD) - H4 OR L4 (4WD) SHIFT

C133832E01
  1. Start the engine.

  1. Move the transfer shift lever from the H2 position to the H4 or L4 position.

  1. Check that the 4WD indicator light illuminates.

  1. Move the transfer shift lever from the H4 or L4 position to the H2 position.

  1. Check that the 4WD indicator light turns off.

    HINT:
    1. If the indicator light does not turn off when you move the transfer shift lever into H2, drive straight ahead while accelerating or decelerating, or drive in reverse.
    2. If a shift remains incomplete for 30 minutes, the 4WD indicator light will begin flashing.


CHECK 4WD CONTROL ECU

G100317E01
  1. Measure the voltage and resistance of the connector.

    Standard voltage:
    Tester Connection
    Wiring Color
    Condition
    Specified Condition
    F14-10 (IG) - F14-5 (GND)
    B-Y - W-B
    Ignition switch ON
    11 to 14 V
    F14-7 (IND1) - F14-5 (GND)
    W-R - W-B
    Ignition switch ON and transfer shift lever position H2
    11 to 14 V
    F14-7 (IND1) -F14-5 (GND)
    W-R - W-B
    Ignition switch ON and transfer shift lever position H4 or L4
    0 to 3.5 V
    F14-8 (ADD) - F14-5 (GND)
    R-B - W-B
    Ignition switch ON and A.D.D. NOT LOCKED
    11 to 14 V
    F14-8 (ADD) - F14-5 (GND)
    R-B - W-B
    Ignition switch ON and A.D.D. LOCKED
    Below 1.5 V
    F14-6 (4WD) - F14-5 (GND)
    B - W-B
    Ignition switch ON and transfer shift lever position H2
    11 to 14 V
    F14-6 (4WD) - F14-5 (GND)
    B - W-B
    Ignition switch ON and transfer shift lever position H4 or L4
    Below 1.5 V
    F14-1 (DL1) - F14-5 (GND)
    R-Y - W-B
    Ignition switch ON and A.D.D. NOT LOCKED
    Below 1.5 V
    F14-1 (DL1) - F14-5 (GND)
    R-Y - W-B
    Ignition switch ON and A.D.D. LOCKED
    11 to 14 V
    F14-2 (DL2) - F14-5 (GND)
    R-W - W-B
    Ignition switch ON and A.D.D. LOCKED
    Below 1.5 V
    F14-2 (DL2) - F14-5 (GND)
    R-W - W-B
    Ignition switch ON and A.D.D. NOT LOCKED
    11 to 14 V
    F14-4 (DM1) - F14-3 (DM2)
    Y - R
    Ignition switch ON and A.D.D. NOT LOCKED → LOCKED
    11 to 14 V or 0 to 14 V pulse generation → less than 0.5 V
    F14-3 (DM2) - F14-4 (DM1)
    R - Y
    Ignition switch ON and A.D.D. LOCKED → NOT LOCKED
    11 to 14 V or 0 to 14 V pulse generation → less than 0.5 V


    Standard resistance:
    Tester Connection
    Wiring Color
    Condition
    Specified Condition
    F14-5 (GND) - Body ground
    W-B - Body ground
    Always
    Below 1 Ω

    1. If the result is not as specified, the 4WD control ECU may have a malfunction.
    1. Check for continuity between the wire harnesses.
    2. Reinstall the ECU.
    3. Replace the ECU if there is still no continuity between the wire harnesses after completion of procedures 1 and 2.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)INSPECTION (Jul 2007 – Jul 2009) →