ADJUSTMENT
Removal / installation · Vehicles built from Jul 2007
| 1. BEFORE REFILL TRANSMISSION |
- This transmission requires Toyota Genuine ATF WS or equivalent transmission fluid.
- After servicing the transmission, you must refill the transmission with the correct amount of fluid.
- Maintain the vehicle in a horizontal position while adjusting the fluid level.
- If the transmission pan, drain plug, valve body or torque converter is replaced, proceed to the "transmission pan fill" procedures.
- If the transmission hose or output shaft oil seal is replaced, remove the refill plug and proceed to the "transmission fill" procedures.
- If the entire transmission is replaced, proceed to the "fluid circulation" procedures.
- HINT:
- New transmissions are already filled with transmission fluid.
| 2. TRANSMISSION PAN FILL |
Remove the refill plug and overflow plug.

Text in Illustration *1
Refill Plug
*2
Overflow Plug
*3
Refill Hole
Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

Text in Illustration *1
Overflow Tube
*a
Specified Fiuid Level
Reinstall the overflow plug.
| 3. TRANSMISSION FILL |
Fill the transmission with the amount of fluid listed in the table below.
Reinstall the refill plug to prevent the fuel from splashing.
- Standard Capacity:
Repair
Fill Amount
Transmission hose and pipe removal
0.6 liters (0.63 US qts, 0.53 lmp.qts)
Output shaft oil seal replacement
0.4 liters (0.42 US qts, 0.35 lmp.qts)
Transmission pan and drain plug removal
1.7 liters (1.8 US qts, 1.5 lmp.qts)
Transmission valve body removal
4.3 liters (4.54 US qts, 3.78 lmp.qts)
Torque converter removal
5.4 liters (5.71 US qts, 4.75 lmp.qts)
- HINT:
- If the amount of fluid listed in the table cannot be added, perform the next step.
When the amount of fluid listed in table cannot be added:
Install the refill plug.
Allow the engine to idle with the air conditioning OFF.
Move the shift lever through the entire gear range to circulate fluid.
Wait for 30 seconds with the engine idling.
Stop the engine.
Remove the refill plug and add fluid.
Reinstall the refill plug.
| 4. FLUID CIRCULATION |
Allow the engine to idle with the air conditioning OFF.
Move the shift lever through the entire gear range to circulate fluid.
| 5. FLUID TEMPERATURE CHECK |
- NOTICE:
- The ATF temperature can be confirmed by checking the indicator light in the meter or by using the intelligent tester. When using the intelligent tester, it is necessary to change to temperature detection mode in order to idle the vehicle appropriately.
When using the intelligent tester:
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.
Check ATF temperature.
- NOTICE:
- The ATF temperature must be between 36°C (97°F) to 46°C (115°F).
- If the ATF temperature is not between 36°C (97°F) to 46°C (115°F), turn the ignition switch off and wait until the fluid temperature drops between 36°C (97°F) to 46°C (115°F).
- The ATF temperature must be between 36°C (97°F) to 46°C (115°F).
According to the display on the intelligent tester, perform the Active Test "Connect the TC and TE1".
- HINT:
- Indicator lights of the combination meter blink to output DTCs when TC and TE1 are connected.
Start the engine.
- NOTICE:
- Check that electrical systems such as the air conditioning system, audio system and lighting system are off.
When not using the intelligent tester (using indicator light):

Text in Illustration *a
Front view of DLC3
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
- SST
- 09843-18040
Start the engine.
- NOTICE:
- Check that electrical systems such as the air conditioning system, audio system and lighting system are off.
- HINT:
- Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected.
Slowly move the shift lever from P to L. Then return the shift lever to P.
- HINT:
- Slowly move the shift lever to circulate the fluid through each part of the transmission.
Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

- Standard condition:
- Indicator light (A/T OIL TEMP) remains illuminated for 2 seconds and then turns off.
When using the intelligent tester:
Return the shift lever to P and press OFF on the Active Test display.
When not using the intelligent tester:
Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).
Allow the engine to idle until the fluid temperature reaches 36 to 46°C (97 to 115°F).
The indicator (A/T OIL TEMP) will come on again when the fluid temperature reaches 36°C (97°F) and will blink when it exceeds 46°C (115°F).
- Indicator Indication of ATF Temperature:
Below Proper Temperature
Proper Temperature
Higher than Proper Temperature
Data List [A/T Oil Temperature 1]
36°C (97°F) or less
Data List [A/T Oil Temperature 1]
36 to 46°C (97 to 115°F)
Data List [A/T Oil Temperature 1]
46°C (115°F) or higher
Indicator light (A/T OIL TEMP)
Turn off
Indicator light (A/T OIL TEMP)
Turn on
Indicator light (A/T OIL TEMP)
Blinking
- NOTICE:
- When checking the fluid temperature using the indicator light, make sure that the shift lever is in P.
- Perform the fluid level inspection while the indicator light is on.
- When checking the fluid temperature using the indicator light, make sure that the shift lever is in P.
- NOTICE:
- Perform the fluid level inspection while the indicator light is on.
| 6. FLUID LEVEL CHECK |
- NOTICE:
- The ATF temperature must be between 36° (97°F) and 46°C (115°F) to accurately check the fluid level.
Remove the overflow plug with the engine idling.

Text in Illustration *1
Overflow Tube
*a
Specified Fiuid Level
Check that the fluid comes out of the overflow tube.
If fluid does not come out, proceed to the "Transmission Refill" procedures.
If fluid comes out, wait until the overflow slows to a trickle and proceed to the "Complete" procedures.
| 7. TRANSMISSION REFILL |
Remove the overflow plug.
Remove the refill plug.
Add ATF into the refill hole until ATF flows from the overflow tube.
Wait until the overflow slows to a trickle and proceed to the "Complete" procedures.
| 8. COMPLETE |
Install a new gasket and the overflow plug.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Stop the engine.
Install a new gasket and the refill plug.
- Torque:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
