2011-2016 FJ Cruiser · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. BEARING POSITION

D028813E02

Bearing diameter:
Mark
Front Race Diameter Inside / Outside
Thrust Bearing Diameter Inside / Outside
Rear Race Diameter Inside / Outside
A
73.6 mm (2.898 in.) / 102.0 mm (4.016 in.)
71.9 mm (2.831 in.) / 85.6 mm (3.370 in.)
-
B
38.0 mm (1.496 in.) / 57.0 mm (2.244 in.)
43.4 mm (1.709 in.) / 58.3 mm (2.295 in.)
-
C
-
55.7 mm (2.193 in.) / 76.4 mm (3.008 in.)
53.7 mm (2.114 in.) / 74.0 mm (2.913 in.)
D
33.4 mm (1.315 in.) / 49.0 mm (1.929 in.)
32.1 mm (1.264 in.) / 49.35 mm (1.943 in.)
32.1 mm (1.2649 in.)/ 49.0 mm (1.929 in.)
E
-
21.5 mm(0.847 in.) / 40.8 mm (1.606 in.)
-
F
48.5 mm (1.909 in.) / 62.7 mm (2.469 in.)
45.9 mm (1.807 in.) / 64.0 mm (2.520 in.)
-


2. INSTALL NO. 4 BRAKE PISTON

D028795E06
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the brake reaction sleeve.

  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the No. 4 brake piston.

  1. Install the No. 4 brake piston onto the reaction sleeve.


3. INSTALL BRAKE REACTION SLEEVE

D028080E03
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent, and install it to the reaction sleeve.

  1. With the No. 1 brake piston underneath (the rear side), install the brake reaction sleeve and No. 1 brake piston onto the transmission case.

    NOTICE:
    Be careful not to damage the O-rings.


4. INSTALL 1ST AND REVERSE BRAKE PISTON

D028081E03
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent.

  1. Install the O-ring onto the 1st and reverse brake piston.

  1. With the spring seat of the piston facing upward (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.

  1. D028549E01
    Place the piston return spring onto the 1st and reverse brake piston.


5. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028082E01
  1. Place SST on the spring retainer, and compress the return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)


6. INSTALL REAR PLANETARY GEAR ASSEMBLY

D027947E01
  1. Install the thrust needle roller bearing.

    Thrust needle roller bearing diameter:
    Item
    Inside
    Outside
    Thrust needle roller bearing
    45.9 mm (1.807 in.)
    64.0 mm (2.520 in.)

  1. D027946E03
    Install the thrust needle roller bearing.

  1. Coat the No. 9 thrust bearing race with petroleum jelly, and install it onto the rear planetary ring gear.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    21.5 mm (0.847 in.)
    40.8 mm (1.606 in.)
    Race
    48.5 mm (1.909 in.)
    62.7 mm (2.469 in.)

  1. D027945E01
    Install the rear planetary gear assembly.


7. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

D027966E01
  1. Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.

  1. D029831E01
    Using vernier calipers, measure the level difference (length A) between the upper surface of the 1st and reverse brake piston and the hitting surface of the No. 4 brake flange at both ends across a diameter, and calculate the average.

    NOTICE:
    The 1st and reverse brake piston must be installed tightly to the end face of the transmission case.

    HINT:
    Length A = 36.35 to 37.09 mm (1.431 to 1.460 in.)

  1. D029832E03
    Using vernier calipers, measure the thickness (length B) of the 2 brake flanges, the 7 No. 4brake plates and the 8 No. 4 brake discs altogether at both ends across a diameter, and calculate the average.

    HINT:
    Pack clearance = Length A - Length B - 0.25 mm - 1.8 mm
    Length B = 36.04 to 37.14 mm (1.419 to 1.462 in.)

    Pack clearance:
    0.8 to 1.1 mm (0.031 to 0.043 in.)

  1. If the pack clearance is outside the standard, select and install a brake flange that makes the pack clearance within the standard.

    H thickness:
    No.
    Thickness
    No.
    Thickness
    0
    0 mm (0 in.)
    8
    0.8 mm (0.032 in.)
    2
    0.2 mm(0.008 in.)
    10
    1.0 mm (0.039 in.)
    4
    0.4 mm (0.016 in.)
    12
    1.2 mm (0.047 in.)
    6
    0.6 mm (0.024 in.)
    14
    1.4 mm (0.055 in.)


8. INSTALL NO. 4 BRAKE DISC

D027944E01
  1. Install the 7 plates, 8 discs and 2 flanges.

    Install in order:
    F - D - P - D - P - D- P - D -P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate, D = Disc, F = Flange


9. INSTALL BRAKE PLATE STOPPER SPRING

D027943E01
  1. Install the brake stopper spring.


10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965E05
  1. Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange onto the intermediate shaft.

    Bearing and race diameter mm (in.):
    Item
    Inside
    Outside
    No. 7 thrust bearing race
    33.4 (1.315)
    49.0 (1.929)
    Thrust needle roller bearing
    32.1 (1.264)
    49.35 (1.943)
    No. 8 thrust bearing race
    32.1 (1.264)
    49.0 (1.929)


11. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

D027964E01
  1. Install the No. 3 1-way clutch assembly and the 1-way clutch inner race onto the intermediate shaft.


12. INSTALL INTERMEDIATE SHAFT

D027942E01
  1. Install the intermediate shaft with the No. 3 1-way clutch assembly onto the case.

  1. D027927E03
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07050, 09350-07060)


13. INSTALL CENTER PLANETARY GEAR ASSEMBLY

D031532
  1. Install the center planetary gear assembly and planetary sun gear into the case.

  1. Coat the No. 4 thrust bearing race and thrust needle roller bearing with petroleum jelly, and install them onto the center planetary ring gear.

    Race and Bearing diameter:
    Item
    Inside
    Outside
    Race
    53.7 mm (2.114 in.)
    74.0 mm (2.913 in.)
    Bearing
    55.7 mm (2.192 in.)
    76.4 mm (3.008 in.)


14. INSTALL NO. 2 BRAKE PISTON

D028797E03
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the No. 2 brake piston.

  1. Be careful not to damage the O-rings. Press the No. 2 brake piston into the No. 2 brake cylinder with both hands.

  1. Install the No. 2 brake piston onto the case.


15. INSTALL NO. 2 BRAKE DISC

D027938E06
  1. Install the flange, 3 plates, 3 discs and brake piston return spring.

    Install in order:
    F - D- P- D- P- D- P

    HINT:
    P = Plate, D = Disc, F = Flange

  1. D028818E03
    Using SST and press, install the No. 2 brake spring snap ring.
    SST
    09351-40010  


16. INSTALL NO. 1 BRAKE PISTON

D028539E03
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the No. 1 brake piston.

  1. Be careful not to damage the O-rings. Press the No. 1 brake piston into the No. 1 brake cylinder with both hands.


17. INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935E01
  1. Install the brake piston return spring and No. 1 brake piston with the No. 1 brake cylinder into the transmission case.


18. INSTALL BRAKE PISTON RETURN SPRING SNAP RING

D028819E03
  1. Using SST and a press, install the brake piston return spring snap ring.

    SST
    09351-40010  


19. INSTALL NO. 1 BRAKE DISC

D027933E04
  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    F - D - P - D - P - D - P

    HINT:
    P = Plate, D = Disc, F = Flange


20. INSTALL CENTER PLANETARY RING GEAR

D028541E01
  1. Install the center planetary ring gear and front planetary ring gear flange into the front planetary ring gear.

  1. D028540E01
    Using a screwdriver, install the snap ring.


21. INSTALL FRONT PLANETARY RING GEAR

D031542
  1. Install the front planetary ring gear into the case.


22. INSTALL FRONT PLANETARY GEAR ASSEMBLY

D027931E04
  1. Install the thrust needle roller bearing and No. 2 planetary carrier thrust washer.

  1. Coat the No. 3 thrust bearing race with petroleum jelly, and install it onto the front planetary ring gear.

    Thrust needle roller bearing and race diameter:
    Item
    Inside
    Outside
    Thrust needle roller bearing
    43.4 mm (1.709 in.)
    58.3 mm (2.295 in.)
    Race
    38.0 mm (1.496 in.)
    57.0 mm (2.244 in.)

  1. D027930E01
    Install the front planetary gear assembly and 1-way clutch inner race into the case.


23. INSPECT NO. 1 PISTON STROKE OF BRAKE PISTON

D028814E01
  1. Make sure the No. 1 brake piston moves smoothly when applying and releasing the compressed air into the transmission case.

  1. D028815E01
    Using a feeler gauge, measure the B3 brake pack clearance between the snap ring and flange.

    Piston stroke:
    0.42 to 0.72 mm (0.017 to 0.028 in.)

    If the piston stroke is outside the specification, parts may have been assembled incorrectly.
    Perform the reassembly again.
    If the piston stroke is still outside the specification, select another flange.

    HINT:
    There are 4 different thicknesses for the flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    0
    2.0 mm (0.079 in.)
    2
    2.4 mm (0.094 in.)
    1
    2.2 mm (0.087 in.)
    3
    2.6 mm (0.102 in.)


24. INSTALL 2ND BRAKE PISTON

D028546E04
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the 2nd brake piston.

  1. Be careful not to damage the O-rings. Press the 2nd brake cylinder into the 2nd brake piston with both hands.

  1. D028817E03
    Using SST and press, install the snap ring.
    SST
    09351-40010  

    NOTICE:
    Make sure that the end gap of the snap ring is not aligned with the spring retainer claw.


25. INSTALL 2ND BRAKE CYLINDER

D027929E01
  1. Install the 2nd brake cylinder into the case.


26. INSTALL 1-WAY CLUTCH ASSEMBLY

D027928E01
  1. Install the 1-way clutch assembly and the thrust washer into the case.


27. INSTALL 2ND BRAKE PISTON HOLE SNAP RING

D027927E02
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)


28. INSTALL NO. 3 BRAKE DISC

D027926E04
  1. Install the flanges, 4 discs, 4 plates and the cushion plate onto the case.

    Install in order:
    F - D - P - D - P - D - P - D - P - C

    HINT:
    P = Plate, D = Disc, F = Flange C = Cushion


29. INSTALL NO. 3 BRAKE SNAP RING

D027925E01
  1. Using a screwdriver, install the snap ring.


30. INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

D027994E01
  1. Coat the race with petroleum jelly and install it onto the No. 2 clutch drum thrust washer.

  1. Install the No. 2 1-way clutch assembly washer.


31. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C133777
  1. Install the thrust needle roller bearing.

  1. Coat the race with petroleum jelly and install it onto the clutch drum thrust washer.

    Thrust needle roller bearing and diameter:
    Item
    Inside
    Outside
    Thrust needle roller bearing
    71.9 mm (2.831 in.)
    85.6 mm (3.370 in.)
    Race
    73.6 mm (2.898 in.)
    102.0 mm (4.016 in.)

  1. Install the clutch drum thrust washer and race onto the clutch drum and input shaft assembly.

  1. D029833E01
    Install the input shaft sub-assembly with the direct and reverse multiple disc assembly onto the transmission case.


32. INSTALL OIL PUMP ASSEMBLY

D028809E01
  1. Install the No. 1 thrust bearing race onto the front oil pump.

    No. 1 thrust bearing race diameter:
    Item
    Inside
    Outside
    Race
    74.2 mm (2.921in.)
    87.74 mm (3.454 in.)

  1. D028796E01
    Coat a new O-ring with Toyota Genuine ATF WS or equivalent, and install it onto the oil pump assembly.

  1. Place the oil pump through the input shaft, and align the bolt holes in the oil pump assembly with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

    NOTICE:
    Do not push on the oil pump strongly, as the oil seal ring will stick to the direct clutch drum.

  1. D027921E01
    Install the 10 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


33. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

D028548E02
  1. Using SST, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)

  1. Coat the oil seal lips with MP grease.


34. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION

D028547E02
  1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the O/D direct clutch, use the C3 accumulator piston holes indicated in the illustration.
    If there is no sound, disassemble and check the installation condition of the parts.

    1. (1) No. 2 clutch (C2)
    2. (2) No. 3 clutch (C3)
    3. (3) No. 1clutch (C1)
    4. (4) No. 3 brake (B3)
    5. (5) No. 1 brake (B1)
    6. (6) No. 2 brake (B2)
    7. (7) No. 4 brake (B4)


35. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

D028798E01
  1. Install a new spacer onto the manual valve lever.

  1. Install the manual valve lever shaft onto the transmission case through the manual valve lever.

  1. D028799E01
    Using a hammer, tap in a new spring pin.

  1. D028800E01
    Align the manual valve lever indentation with the spacer hole, and stake them together with a punch and hammer.

  1. Make sure the shaft rotates smoothly.


36. INSTALL PARKING LOCK PAWL SHAFT

D028846E04
  1. Install the E-ring onto the shaft.

  1. Install the parking lock pawl, shaft and spring.


37. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

D012709E01
  1. Connect the parking lock rod to the manual valve lever.


38. INSTALL PARKING LOCK PAWL BRACKET

D012708E01
  1. Place the parking lock pawl bracket onto the transmission case and tighten the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. D028801E03
    Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.


39. INSTALL C-1 ACCUMULATOR VALVE

D028802E01
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent, and install it onto the piston.

  1. D028803E01
    Install the 2 springs and accumulator valve into the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-1 Inner
    30.40 mm (1.197 in.)
    11.40 mm (0.449 in.)
    Pink
    C-1 Outer
    48.76 mm (1.920 in.)
    16.60 mm (0.654 in.)
    Light green


40. INSTALL C-3 ACCUMULATOR PISTON

D028802E05
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent, and install it into the piston.

  1. D028804E01
    Install the 2 springs and accumulator piston into the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-3 Inner
    44.0 mm (1.732 in.)
    14.0 mm (0.551 in.)
    Yellow
    C-3 Outer
    73.35 mm (2.888 in.)
    19.90 mm (0.784 in.)
    Red


41. INSTALL B-3 ACCUMULATOR PISTON

D028802E03
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the piston.

  1. D028805E01
    Install the spring and accumulator piston into the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    B-3
    70.5 mm (2.776 in.)
    19.7 mm (0.776 in.)
    Purple


42. INSTALL C-2 ACCUMULATOR PISTON

D028802E04
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install them onto the piston.

  1. D028806E01
    Install the spring and accumulator piston into the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-2
    62.0 mm (2.441 in.)
    15.9 mm (0.626 in.)
    White


43. INSTALL CHECK BALL BODY

D027914E04
  1. Install the check ball body and spring.


44. INSTALL BRAKE DRUM GASKET

D027969E01
  1. Install the 3 brake drum gaskets.


45. INSTALL TRANSAXLE CASE GASKET

D027968E04
  1. Install the 3 transaxle case gaskets.


46. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

D012707E01
  1. Align the groove of the manual valve with the pin of the lever.

  1. D012705E02
    Install the 19 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is as indicated below.

    Bolt length:
    25 mm (0.98 in.) for bolt A
    36 mm (1.42 in.) for bolt B


47. INSTALL TRANSMISSION WIRE

D027912E01
  1. Install a new O-ring onto the transmission wire.

  1. Install the transmission wire harness.

  1. Install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the solenoid connector.

  1. D012704E03
    Connect the 7 solenoid connectors.

  1. Install the ATF temperature sensor.

  1. Install the 2 clamps and the 2 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf } for bolt A
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt B

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    12 mm (0.47 in.) for bolt A
    36 mm (1.42 in.) for bolt B


48. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

D012703E01
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent, and install them onto the valve body oil strainer assembly.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }


49. INSTALL TRANSMISSION OIL CLEANER MAGNET

D027992E02
  1. Install the 4 transmission oil cleaner magnets.


50. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Install a new gasket onto the oil pan.

  1. Install the 20 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


51. INSTALL TRANSMISSION CASE ADAPTOR OIL SEAL

C111210E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09226-10010  


52. INSTALL TRANSMISSION CASE ADAPTER SUB-ASSEMBLY

C111211E02
  1. Apply seal packing or equivalent to the 8 bolts.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

  1. C111208E01
    Install the transmission case adapter sub-assembly with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    50 mm (1.969 in.) for bolt A
    40 mm (1.575 in.) for bolt B


53. INSTALL AUTOMATIC TRANSMISSION HOUSING

C111207E01
  1. Clean the threads of the bolts and case with white gasoline.

  1. Install the transmission housing with the 10 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf } for bolt A
    57 N*m{ 581 kgf*cm , 42 ft.*lbf } for bolt B
    34 N*m{ 345 kgf*cm , 25 ft.*lbf } for bolt C

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    Bolt A: 14 mm
    Bolt B: 17 mm
    Bolt C: 14 mm


54. INSTALL AUTOMATIC TRANSAXLE BREATHER TUBE

D027970E01
  1. Install a new O-ring onto the breather tube.

  1. Install the breather tube with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


55. INSTALL TRANSMISSION REVOLUTION SENSOR

C111258
  1. Coat 2 new O-rings with AFT, and install one onto each transmission revolution sensor.

  1. Install the 2 transmission revolution sensors.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


56. INSTALL OIL COOLER TUBE UNION

D027989E01
  1. Coat 2 new O-rings with Toyota Genuine ATF WS or equivalent, and install one onto each oil cooler tube union.

  1. Install the 2 oil cooler tube unions.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


57. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903E01
  1. Install the park/neutral position switch onto the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. D028682E01
    Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. D027980E03
    Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 129 kgf*cm , 9.4 ft.*lbf }

  1. D027990E01
    Using a screwdriver, bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.


58. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

D027971E02
  1. Install the control shaft lever LH with the washer and nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

← INSPECTION (from Jul 2007)COMPONENTS (from Jul 2007) →