2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B130597
    Disengage the 14 claws and remove the front door scuff plate.


3. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


4. REMOVE FRONT FLOOR FOOTREST

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


5. REMOVE FOOTREST CLIP

  1. B130587
    Remove the 2 footrest clips.


6. REMOVE COWL SIDE TRIM BOARD RH

  1. B130599
    Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.


7. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B138475
    Remove the front door opening trim weatherstrip to the extent that the front pillar garnish and the instrument panel lower finish panel can be removed.


9. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


10. REMOVE ASSIST GRIP PLUG

B138476E01

HINT:
Use the same procedure to remove all the assist grip plugs.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.


11. REMOVE ASSIST GRIP ASSEMBLY

B138478E01

HINT:
Use the same procedure to remove all the assist grips.

  1. Remove the 2 screws and the assist grip.


12. REMOVE FRONT PILLAR GARNISH RH

  1. B130608
    Disengage the 2 clips and the claw and remove the front pillar garnish.


13. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


14. REMOVE ASSIST GRIP RETAINER RH

B133881
  1. Remove the 2 bolts and remove the assist grip retainer.


15. REMOVE ASSIST GRIP RETAINER LH

HINT:
Use the same procedure as for the RH side.


16. REMOVE INSTRUMENT PANEL GARNISH LH

  1. B133886
    Remove screw <H>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


17. REMOVE INSTRUMENT PANEL GARNISH RH

  1. B133887
    Remove screw <H>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


18. REMOVE INTEGRATION CONTROL PANEL ASSEMBLY

  1. B133888
    Remove the 2 <H> screws.

  1. Disengage the 4 clips and remove the integration control panel assembly.

  1. Disconnect the 3 connectors.


19. REMOVE RADIO RECEIVER ASSEMBLY

  1. B130575
    Remove the 4 bolts and the radio receiver.

  1. B130576
    Disconnect the plug, the head unit connector and the 2 radio connectors.


20. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B133898E02
  1. Disengage the 2 A claws and 2 B claws.

  1. Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 C claws and remove the parking brake hole cover.


21. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

  1. B133893
    Remove the shift lever knob.


22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)

  1. B133895
    Remove the shift lever knob.


23. REMOVE FRONT CONSOLE BOX UPPER PANEL SUB-ASSEMBLY

  1. B133897
    Shift the shift lever into the N position.

  1. Disengage the 5 clips and 3 claws and remove the console upper rear panel.


24. REMOVE FRONT CONSOLE BOX BOTTOM MAT

  1. B133899
    Remove the box bottom mat.


25. REMOVE FRONT CONSOLE BOX

  1. B133851
    Remove the 4 <D> bolts.

  1. Disengage the 5 claws and remove the console box.


26. REMOVE FRONT CONSOLE BOX UPPER PANEL GARNISH

B133900E01
  1. Disengage claw A and the clip.

  1. Slide the console upper panel garnish toward the rear of the vehicle, disengage the claw B and remove the console upper panel garnish.


27. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY

  1. B133852
    Remove the 2 clips and 2 <F> bolts.

  1. Disengage the 3 clips and 2 claws and remove the instrument lower cover.


28. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY LH

  1. B133853
    Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


29. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


30. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY LH

  1. B133860
    Remove the 2 <F> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


31. REMOVE INSTRUMENT LOWER PANEL

  1. B133864
    Remove the 4 <F> bolts and remove the lower instrument panel.


32. REMOVE INSTRUMENT CLUSTER LOWER FINISH PANEL

  1. B133861
    Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.

  1. Disconnect the connectors.


33. REMOVE COMBINATION METER ASSEMBLY

  1. B133862
    Remove the 4 screws.

  1. B133863
    Disconnect the 2 connectors and clamp and remove the combination meter.


34. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

  1. B133854E01
    Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.

  1. B133855
    Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.


35. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH

  1. B133857
    Remove screw <A>.

  1. Disengage the 2 clips and claw and remove the instrument panel lower finish panel.

  1. Separate the connectors from the instrument panel lower finish panel.


36. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY RH

  1. B176533E01
    Remove the No. 2 instrument panel register assembly (Previous Version).

    1. Remove the clip.

    2. Disengage the 4 clips and 2 claws and remove the instrument panel register.

      NOTICE:
      1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
      2. Pull the instrument panel register up diagonally to remove it.

  1. B188205E01
    Remove the No. 2 instrument panel register assembly (New Version).

    1. Apply protective tape, as shown in the illustration.

    2. Using a thin-bladed screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel hole cover.

    3. B188206E01
      Remove the bolt and clip.

    4. Disengage the 4 clips and 2 claws and remove the instrument panel register.

      NOTICE:
      1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
      2. Pull the instrument panel register up diagonally to remove it.


37. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY RH

  1. B133865
    Disengage the 4 clips and claw and remove the instrument panel speaker panel.


38. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


39. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

B130583E01

HINT:
Use the same procedure for both sides.

  1. Remove the 2 bolts and the front No. 2 speaker.

  1. Disconnect the speaker connector.


40. DISCONNECT PASSENGER AIRBAG CONNECTOR

B133890E02
  1. Slide the slider and disconnect the passenger airbag connector.


41. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Disengage the clamps and disconnect the connectors.

  1. Remove the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G> and remove the instrument panel.

    B133866E01


42. REMOVE INSTRUMENT PANEL FINISH PANEL END

  1. B133889
    Disengage the 3 claws and remove the instrument panel finish panel end.


43. REMOVE ANTENNA CORD SUB-ASSEMBLY

  1. B135181
    Disengage the 4 clamps.

  1. Remove the 3 pieces of tape and the antenna cord.

← COMPONENTS (from Jul 2007)REMOVAL (Nov 2010 – Jul 2012) →