2011-2016 FJ Cruiser · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY

C013829
  1. Fix the rear differential carrier assembly to the overattachment.


2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E03
  1. Using a dial indicator, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    Vertical runout: 0.10 mm (0.0039 in.)
    Lateral runout: 0.10 mm (0.0039 in.)

    If the runouts are not with the specifications, replace the companion flange.


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

C014075
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.


4. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C028211
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.


5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.


6. INSPECT TOTAL PRELOAD

C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.


7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

G020268
  1. Remove the 4 bolts and actuator from the differential carrier.

  1. Remove the O-ring.


8. REMOVE NO.1 TRANSFER INDICATOR SWITCH

G020269
  1. Remove the indicator switch and gasket.


9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

G020270
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and ball.

  1. G020271
    Using a 5 mm pin punch and hammer, remove the slotted pin.

  1. G020272
    Remove the 2 bolts from the shaft retainer.

  1. Using a plastic hammer, remove the shaft retainer.

  1. Remove the shift fork shaft.


10. REMOVE REAR DRIVE PINION NUT

F044346E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  

  1. SA02349E06
    Using SST to hold the drive pinion companion flange, remove the nut.
    SST
    09330-00021  


11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F052175E02
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


12. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

F040564E04
  1. Using SST and a press, remove the dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  


13. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  


14. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

15. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Z000641E04
  1. Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09556-22010  


16. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

C030538
  1. Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.


17. REMOVE DIFFERENTIAL CASE ASSEMBLY

F052179E01
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.

  1. C028220
    Remove the rear differential case sub-assembly and 2 case bearings from the differential carrier.

    HINT:
    Tag the 2 case bearings outer races to show the locations for reassembly.


18. REMOVE DIFFERENTIAL DRIVE PINION

C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.


19. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

R010668E02
  1. Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If either the drive pinion or ring gear is damaged, replace them as a set.


20. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

21. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

F044358E02
  1. Using SST, remove the front tapered roller bearing from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and a hammer, remove the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.


22. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.


23. REMOVE DIFFERENTIAL RING GEAR

F052180E01
  1. Place matchmarks on the ring gear and differential case.

  1. Using a screwdriver and a hammer, unstake the lock plates.

  1. Remove the 10 ring gear set bolts and 5 lock plates.

  1. C014054
    Using a plastic hammer, tap on the ring gear to separate it from the differential case.


24. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

G020277
  1. Install the rear differential case bearing onto the differential case.

  1. Install the differential case onto the differential carrier.

  1. Install the 2 bearing caps and 4 bolts onto the differential carrier.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. Inspect the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.


25. REMOVE REAR DIFFERENTIAL CASE BEARING

F040345E03
  1. Using SST, remove the 2 rear differential case bearings from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)


26. DISASSEMBLE DIFFERENTIAL CASE

F052178E01
  1. Place matchmarks on the LH and RH cases.

  1. Remove the 8 bolts.

  1. ZK09094
    Using a plastic hammer, separate the LH and RH cases.

  1. C090324E02
    Remove these parts from the differential case.
    A
    Side gear
    B
    Side gear thrust washer
    C
    Spider
    D
    Pinion gear
    E
    Pinion gear thrust washer


27. INSPECT REAR DIFFERENTIAL LOCK SLEEVE

G020273
  1. Install the sleeve onto the differential case (LH) and check that it moves smoothly.

  1. Install the side gear onto the sleeve and check that it moves smoothly.

  1. G020274
    Using a feeler gauge, measure the clearance between the shift fork and sleeve.

    Maximum clearance:
    0.15 to 0.35 mm (0.0059 to 0.0138 in.)


28. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that there is no damage to the differential pinion and differential side gear.
    If the differential pinion and/or differential side gear is damaged, replace the differential.


29. INSPECT DIFFERENTIAL CASE ASSEMBLY
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace the differential case.

← REMOVAL (from Aug 2009)DISASSEMBLY (from Aug 2009) →