REASSEMBLY
Removal / installation · Vehicles built from Jul 2007
| 1. INSTALL BRAKE BOOSTER ACCUMULATOR ASSEMBLY |
![]() ![]() |
Place the brake booster pump in a vise lined with a cloth.
Install the brake booster accumulator pipe, compression spring and a new O-ring.
- NOTICE:
- Ensure that no foreign matter enters the pump.
Install the brake booster accumulator onto the brake booster pump.
- Torque:
- 57 N*m{ 585 kgf*cm , 42 ft.*lbf }
| 2. INSTALL PISTON |
Apply lithium soap base glycol grease to a new piston.
Install the piston into the master cylinder body.
Using 2 screwdrivers, install a new C-ring while pressing the piston.

- NOTICE:
- Do not damage the rubber lips on the piston when reassembling.
| 3. INSTALL MASTER CYLINDER BOOT |
| 4. INSTALL MASTER CYLINDER PUSH ROD CLEVIS |
![]() ![]() |
Install the master cylinder side lock nut and rod operating adapter.
- Torque:
- 26 N*m{ 260 kgf*cm , 19 ft.*lbf }
Install the lock nut and push rod clevis.

- Torque:
- 26 N*m{ 260 kgf*cm , 19 ft.*lbf }
| 5. INSTALL MASTER CYLINDER SOLENOID |
![]() ![]() |
Place a new gasket onto the master cylinder solenoid.
Install the master cylinder solenoid with 6 new bolts.

- Torque:
- 32 N*m{ 325 kgf*cm , 24 ft.*lbf }
- NOTICE:
- Do not let water, dust, or other foreign matter adhere to the surface or fitting surfaces of the master cylinder solenoid, master cylinder body and gasket.
| 6. INSTALL BRAKE BOOSTER PUMP BRACKET |
![]() ![]() |
Using a 5 mm hexagon wrench, install the brake booster pump bracket with the 2 bolts.
- Torque:
- 7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
Install the bush onto the brake booster pump bracket.
| 7. INSTALL BRAKE ACTUATOR BRACKET |
![]() ![]() |
Using a 5 mm hexagon wrench, install the brake actuator bracket with the bolt.
- Torque:
- 7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
| 8. INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY |
![]() ![]() |
Using a 4 mm hexagon wrench, install the 2 pins.
- Torque:
- 7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
Install the 2 collars and 2 bushes onto the brake booster with accumulator pump assembly.
Install the brake booster with accumulator pump assembly.

Install a new clip.

Install the wire harnesses with the 2 screws.

- Torque:
- 2.9 N*m{ 30 kgf*cm , 26 in.*lbf }
Install 2 new plugs.

| 9. INSTALL BRAKE ACTUATOR NO. 1 TUBE |
![]() ![]() |
Using a union nut wrench, install the brake actuator tube.
- Torque:
- without union nut wrench:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- with union nut wrench:
- 14 N*m{ 144 kgf*cm , 10 ft.*lbf }
- NOTICE:
- This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
- This torque value is effective when the union nut wrench is parallel to a torque wrench.
- This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
| 10. INSTALL BRAKE ACTUATOR HOSE NO.1 |
![]() ![]() |
Using needle-nose pliers, install the brake actuator hose with the 2 clips.
| 11. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY |
Apply lithium soap base glycol grease to 3 new grommets.
Install the 3 grommets onto the master cylinder body.

- NOTICE:
- The grommets are different sizes. Install the grommets in their correct positions.
Install the master cylinder reservoir with the screw.

- Torque:
- 1.7 N*m{ 17 kgf*cm , 15 in.*lbf }
Using a pin punch and hammer, install a new pin onto the master cylinder reservoir.

| 12. INSTALL BRAKE ACTUATOR NO. 1 BRACKET |
Install the fluid level warning switch connector.
Using a 5 mm hexagon wrench, install the brake actuator bracket with the bolt.

- Torque:
- 7.8 N*m{ 80 kgf*cm , 69 in.*lbf }








