REASSEMBLY
Removal / installation · Vehicles built Jul 2007 – Jul 2009
Versions by build date: Jul 2007 – Jul 2009 from Aug 2009
- NOTICE:
- When installing, coat the parts indicated by the arrows with power steering fluid (Click here).
| 1. INSTALL VANE PUMP HOUSING OIL SEAL |
![]() ![]() |
Coat a new vane pump housing oil seal lip with power steering fluid.
Using SST and a press, install a new oil seal.
- SST
- 09950-60010
(09951-00280)
09950-70010 (09951-07100)
- NOTICE:
- Make sure that the oil seal is installed facing in the correct direction.
| 2. INSTALL PULLEY SHAFT SUB-ASSEMBLY |
![]() ![]() |
Coat the bushing inner surface of the vane pump housing front with power steering fluid.
Gradually insert the vane pump shaft.
- NOTICE:
- Do not damage the vane pump housing oil seal lip in the vane pump housing front.
| 3. INSTALL VANE PUMP FRONT SIDE PLATE |
![]() ![]() |
Coat a new O-ring with power steering fluid and install it onto the vane pump housing front.
Coat a new O-ring with power steering fluid and install it onto the side plate.

Align the dent of the side plate with that of the vane pump housing front and install the side plate.

- NOTICE:
- Make sure that the side plate is installed facing the correct direction.
| 4. INSTALL VANE PUMP CAM RING |
![]() ![]() |
Align the dent of the cam ring with that of the side plate and install the cam ring with the inscribed mark facing outward.
| 5. INSTALL VANE PUMP ROTOR |
![]() ![]() |
Install the vane pump rotor with the inscribed mark facing outward.
Coat the 10 vane plates with power steering fluid.
Install the vane plates with the round ends facing outward.
Using a snap ring expander, install a new snap ring onto the pulley shaft.

| 6. INSTALL VANE PUMP REAR HOUSING |
Coat a new O-ring with power steering fluid and install it onto the vane pump housing rear.
Align the straight pin of the vane pump housing rear with the dents of the cam ring, side plate and vane pump housing front, and install the vane pump housing rear with the 4 bolts.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
| 7. INSPECT PRELOAD |
![]() ![]() |
Check that the pump rotates smoothly without making any abnormal noises.
Provisionally install the service bolt.
- Recommended service bolt:
- Thread diameter:
- 10 mm (0.3937 in.)
- Thread pitch:
- 1.25 mm (0.0492 in.)
- Bolt length:
- 50 mm (1.9685 in.)
Using a torque wrench, check the pump rotating torque.
- Torque:
- 0.27 N*m{ 2.8 kgf*cm , 2.4 in.*lbf }
| 8. INSTALL POWER STEERING OIL PRESSURE SWITCH |
Coat the O-ring with power steering fluid and install it onto the power steering oil pressure switch.
Install the power steering oil pressure switch onto the vane pump.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 9. INSTALL FLOW CONTROL VALVE |
![]() ![]() |
Coat the compression spring and flow control valve with power steering fluid.
Install the compression spring and flow control valve.
Coat a new O-ring with power steering fluid and install it onto the pressure port union.
Install the pressure port union.
- Torque:
- 69 N*m{ 704 kgf*cm , 51 ft.*lbf }
| 10. INSTALL POWER STEERING SUCTION PORT UNION |
Coat a new O-ring with power steering fluid, and install it onto the suction port union.
Install the suction port union with the bolt.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }







