2011-2016 FJ Cruiser · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. INSPECT 6TH GEAR THRUST CLEARANCE

F051109E01
  1. Using a dial indicator, measure the 6th gear thrust clearance.

    Standard clearance:
    0.20 to 0.49 mm (0.0079 to 0.0193 in.)

    If the clearance is outside the specification, replace the defective gear, spacer or shaft.


2. INSPECT 3RD GEAR THRUST CLEARANCE

F051110E01
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.09 to 0.52 mm (0.0035 to 0.0205 in.)

    If the clearance is outside the specification, replace the defective gear, thrust washer, clutch hub or shaft.


3. INSPECT 4TH GEAR THRUST CLEARANCE

F051111E01
  1. Using a dial indicator, measure the 4th gear thrust clearance.

    Standard clearance:
    0.12 to 0.38 mm (0.0047 to 0.0150 in.)

    If the clearance is outside the specification, replace the defective gear, clutch hub or shaft.


4. INSPECT 6TH GEAR RADIAL CLEARANCE

F051106E01
  1. Using a dial indicator, measure the 6th gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


5. INSPECT 3RD GEAR RADIAL CLEARANCE

F051107E01
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


6. INSPECT 4TH GEAR RADIAL CLEARANCE

F051108E01
  1. Using a dial indicator, measure the 4th gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


7. REMOVE TRANSMISSION CLUTCH HUB NO.3 SHAFT SNAP RING

D033652E01
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


8. REMOVE 6TH GEAR

D033653E01
  1. Using SST and a press, remove transmission clutch hub No. 3, the hub sleeve, synchronizer ring and 6th gear from the input shaft.

    SST
    09950-00020  
    09950-70010   (09951-07200)
    09950-60010   (09951-00300)

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand so that it does not fall off.


9. REMOVE 6TH GEAR NEEDLE ROLLER BEARING

F051087E01
  1. Remove the 6th gear needle roller bearing from the input shaft.


10. REMOVE SPACER

F051088E01
  1. Remove the spacer from the input shaft.


11. REMOVE GEAR THRUST WASHER SHAFT SNAP RING

D033654E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.


12. REMOVE 3RD GEAR THRUST WASHER

F051090E01
  1. Remove the 3rd gear thrust washer from the input shaft.


13. REMOVE 3RD GEAR

F051091E01
  1. Remove the 3rd gear from the input shaft.


14. REMOVE STRAIGHT PIN

F051092E01
  1. Remove the straight pin from the input shaft.


15. REMOVE 3RD GEAR NEEDLE ROLLER BEARING

F051093E01
  1. Remove the 3rd gear needle roller bearing from the input shaft.


16. REMOVE SPACER

F051094E01
  1. Remove the spacer from the input shaft.


17. REMOVE NO. 2 SYNCHRONIZER RING SET

F051095E01
  1. Remove the No. 2 synchronizer ring set from the input shaft.


18. REMOVE CLUTCH HUB NO.2 SETTING SHAFT SNAP RING

D033657E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.


19. REMOVE 4TH GEAR

D033658E01
  1. Using SST and a press, remove transmission clutch hub No. 2, the hub sleeve, synchronizer ring and 4th gear from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Support the input shaft by hand so that it does not fall off.


20. REMOVE 4TH GEAR NEEDLE ROLLER BEARING

F051098E01
  1. Remove the 4th gear needle roller bearing from the input shaft.


21. REMOVE INPUT SHAFT FRONT BEARING SNAP RING

D033659E01
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


22. REMOVE INPUT SHAFT FRONT BEARING

D033660E01
  1. Using SST and a press, remove the input shaft front bearing from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Support the input shaft by hand so that it does not fall off.


23. REMOVE NO. 2 TRANSMISSION CLUTCH HUB

C136406E01
  1. Remove the clutch hub, 3 synchromesh shifting keys, 3 balls and 3 springs from the hub sleeve.

    HINT:
    Use a piece of cloth to prevent the ball and spring from flying off.


24. REMOVE NO. 3 TRANSMISSION CLUTCH HUB
  1. Perform the same procedures as for the No. 2 clutch hub.

← COMPONENTS (from Jul 2007)INSPECTION (from Jul 2007) →