2011-2016 FJ Cruiser · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. INSPECT REVERSE GEAR THRUST CLEARANCE

F051532E01
  1. Using a feeler gauge, measure the reverse gear thrust clearance.

    Standard clearance:
    0.125 to 0.375 mm (0.0049 to 0.0148 in.)

    If the clearance is outside the specification, replace the defective gear, spline piece or bearing race.


2. INSPECT 1ST GEAR THRUST CLEARANCE

F051533E01
  1. Using a dial indicator, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the defective gear, clutch hub, spline piece or counter gear.


3. INSPECT 2ND GEAR THRUST CLEARANCE

F051534E01
  1. Using a dial indicator, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the defective gear, clutch hub or counter gear.


4. INSPECT REVERSE GEAR RADIAL CLEARANCE

F051535E01
  1. Using a dial indicator, measure the reverse gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the reverse gear needle roller bearing or shaft.


5. INSPECT 1ST GEAR RADIAL CLEARANCE

F051536E01
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 1st gear needle roller bearing or shaft.


6. INSPECT 2ND GEAR RADIAL CLEARANCE

F051537E01
  1. Using a dial indicator, measure the 2nd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 2nd gear needle roller bearing or shaft.


7. REMOVE COUNTER GEAR FRONT BEARING SNAP RING NO.1

D033690E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.


8. REMOVE COUNTER GEAR FRONT BEARING OR ROLLER

F051539E01
  1. Using SST and a press, remove the counter gear front bearing or roller from the counter gear.

    SST
    09950-00020  
    09950-70010   (09951-07100)
    09950-60010   (09951-00320)


9. REMOVE REVERSE GEAR BEARING RACE INNER

F051540E01
  1. Remove the reverse gear bearing race inner from the counter gear.


10. REMOVE COUNTERSHAFT REVERSE GEAR

F051541E01
  1. Remove the countershaft reverse gear from the counter gear.

  1. Remove the hub sleeve, 2 shifting keys and key spring from the countershaft reverse gear.


11. REMOVE REVERSE GEAR NEEDLE ROLLER BEARING

F051542E01
  1. Remove the reverse gear needle roller bearing from the counter gear.


12. REMOVE NO. 4 SYNCHRONIZER RING

F051543E01
  1. Remove the No. 4 synchronizer ring from the counter gear.


13. REMOVE BALL

F051544E01
  1. Remove the ball from the counter gear.


14. REMOVE COUNTERSHAFT GEAR 1ST SPEED

F051630E01
  1. Using a press, remove the countershaft gear 1st speed together with the reverse gear spline piece from the counter gear.

    SST
    09950-00020  


15. REMOVE 1ST GEAR NEEDLE ROLLER BEARING

F051546E01
  1. Remove the 1st gear needle roller bearing from the counter gear.


16. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

C136407
  1. Remove the No. 1 synchronizer ring set from the counter gear.


17. REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING

D033696E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.


18. REMOVE COUNTER SHAFT 2ND SPEED GEAR

F051632E01
  1. Using a press, remove the counter shaft 2nd speed gear together with the No. 1 transmission clutch hub from the counter gear.

    SST
    09950-00020  


19. REMOVE 2ND GEAR NEEDLE ROLLER BEARING

F051551E01
  1. Remove the 2nd needle roller bearing from the counter gear.


20. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR)

F051633E01
  1. Remove the No. 1 synchronizer ring set from the 2nd gear.


21. REMOVE NO. 1 TRANSMISSION CLUTCH HUB

F051634E02
  1. Remove the hub sleeve, 3 synchromesh shifting keys, 3 balls and 3 springs from the clutch hub.

    HINT:
    Use a piece of cloth to prevent the ball and spring from flying off.


22. REMOVE SNAP RING COUNTER GEAR REAR BEARING

D033689E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.


23. REMOVE RADIAL BALL BEARING INNER RACE

F051635E01
  1. Using SST and a press, remove the needle roller bearing inner race.

    SST
    09950-00020  

← COMPONENTS (from Jul 2007)INSPECTION (from Jul 2007) →