SYSTEM DESCRIPTION
Troubleshooting · Vehicles built Aug 2008 – Oct 2010
Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| SYSTEM DESCRIPTION |
- HINT:
- The skid control ECU forms a single unit with the hydraulic brake booster.
ABS (Anti-lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.

Operation description
The skid control ECU detects the wheel lock condition by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valves to prevent the wheels from locking by controlling the oil pressure of each wheel cylinder.
The ABS warning light comes on when the ABS system malfunctions.
EBD (Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions and vehicle load.
In addition, when braking while cornering, it also controls the brake forces of the right and left wheels, helping to maintain the vehicle behavior.

Operation description
The skid control ECU receives the speed signals from each speed sensor to detect the slip condition of the wheels and sends the control signal to the solenoid.
The solenoid valves control the oil pressure of the rear wheel cylinder and divide the control power appropriately between the front and rear wheels and the right and left wheels.
Both of the ABS and the brake warning lights come on when the EBD system malfunctions.
BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist drivers who cannot generate a large enough brake force during emergency braking, thus helping to maximize the vehicle's brake performance.

Operation description
The skid control ECU receives the speed signals from each speed sensor and the fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is deemed necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valves then control the pressure applied to each wheel cylinder.
The ABS warning light comes on when the BA system malfunctions.
VSC (Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid or strong rear wheel skid during cornering.

Operation description
The skid control ECU determines the vehicle condition by receiving signals from the speed sensors, yaw rate and deceleration sensor, and steering angle sensor. The skid control ECU controls the engine torque through the ECM via CAN communication, and brake fluid pressure through the pump and solenoid valves.
w/o VSC OFF Switch:
The SLIP indicator light blinks and the skid control buzzer sounds when the system is operating. The VSC TRC warning light and the VSC OFF indicator light come on when the VSC system malfunctions.
w/ VSC OFF Switch:
The SLIP indicator light blinks and the skid control buzzer sounds when the system is operating. The SLIP indicator light comes on when the VSC system malfunctions.
TRC (Traction Control)
The TRC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting or accelerating on a slippery surface.

Operation description
The skid control ECU detects the vehicle's slip condition by receiving signals from each speed sensor and the ECM via CAN communication. The skid control ECU controls engine torque through the ECM via CAN communication, and brake fluid pressure through the pump and solenoid valves.
w/o VSC OFF Switch:
The SLIP indicator light blinks when the system is operating. The VSC TRC warning light and SLIP indicator light come on when the TRC system malfunctions.
w/ VSC OFF Switch:
The SLIP indicator light blinks when the system is operating. The SLIP indicator light comes on when the TRC system malfunctions.
A-TRAC (Active Traction Control) (with A-TRAC Switch)
During rugged off-road driving, this function controls the engine output and the brake fluid pressure that is applied to slipping wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD (Limited Slip Differential) effect. As a result, the vehicle's off-road drivability and ability to free itself from bumps have been increased.

Operation description
When the A-TRAC switch is pressed and the A-TRAC system is operative, the A-TRAC indicator light comes on. When the system is operating, the SLIP indicator light blinks.
w/o VSC OFF Switch:
The VSC TRC warning light and SLIP indicator light come on when the A-TRAC system malfunctions.
w/ VSC OFF Switch:
The SLIP indicator light comes on when the A-TRAC system malfunctions.- HINT:
- If the A-TRAC system operates constantly for a long time, the temperature of the actuator in the hydraulic brake booster may increase excessively. In such cases, the skid control buzzer sounds intermittently and the SLIP indicator light comes on. If this condition continues, the skid control buzzer sounds for approximately 1 second and the A-TRAC system is temporarily deactivated. After a while, the SLIP indicator light goes off and the A-TRAC system is reactivated. The vehicle can be driven normally while the A-TRAC system is deactivated.
| ABS with EBD, BA, TRC, A-TRAC and VSC OPERATION |
The skid control ECU calculates vehicle stability tendency based on the signals from the 4 wheel speed sensors, the yaw rate and deceleration sensor, and the steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the brake fluid pressure by the hydraulic brake booster) should be implemented.
| FAIL SAFE FUNCTION |
w/o VSC OFF Switch:
When a failure occurs in the ABS with BA, TRC, A-TRAC and VSC systems, the ABS and VSC TRC warning lights, and VSC OFF and SLIP indicator lights come on, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the brake warning light comes on and its operation is prohibited.
w/ VSC OFF Switch:
When a failure occurs in the ABS with BA, TRC, A-TRAC and VSC systems, the ABS and SLIP indicator lights come on, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the brake warning light comes on and its operation is prohibited.If control is prohibited due to a malfunction during operation, control is disabled gradually to avoid sudden vehicle instability.
| INITIAL CHECK |
When the vehicle speed first reaches approximately 6 km/h (4 mph) or more after the ignition switch is turned ON, each solenoid valve and the motor of the hydraulic brake booster are sequentially activated to perform electrical checks. During the initial check, the operating sound of the motor can be heard from the engine compartment, but this does not indicate a malfunction.
| FUNCTION OF COMPONENTS |
*2: w/ VSC OFF Switch
| Components |
Function |
| Hydraulic brake booster |
|
| Skid control ECU |
|
| Master cylinder pressure sensor |
|
| Accumulator pressure sensor |
|
| Front speed sensor |
|
| Rear speed sensor |
|
| ABS warning light |
Illuminates to inform driver that skid control ECU has detected ABS system malfunction and terminated ABS system operation. |
| BRAKE warning light |
Illuminates to inform driver that skid control ECU has detected BRAKE system malfunction. |
| VSC TRC warning light *1 |
Illuminates to inform driver that skid control ECU has detected VSC system malfunction and terminated VSC system operation. |
| SLIP indicator light *1 |
Blinks to inform driver that VSC, TRC or A-TRAC is in operation. |
| SLIP indicator light *2 |
|
| TRC OFF indicator light *2 |
Illuminates to inform driver that traction control is ready to operate. |
| A-TRAC indicator light |
Illuminates to inform driver that A-TRAC is ready to operate. |
| Yaw rate and deceleration sensor |
Detects vehicle's yaw rate and deceleration and sends signal to skid control ECU via CAN communication system. |
| Steering angle sensor |
Detects steering wheel's steering angle and amount of movement, and then sends signal to skid control ECU via CAN communication system. |
| Skid control buzzer |
|
| ECM |
|
| A-TRAC switch |
Allows driver to turn A-TRAC on and off. |
| VSC OFF switch |
Allows driver to turn vehicle stability control and traction control on and off. |