2011-2016 FJ Cruiser · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


CHECK TRANSPONDER KEY AMPLIFIER

  1. Disconnect the E72 amplifier connector and measure the resistance according to the value(s) in the table below.
    B065593E37

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E72-7 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E72 amplifier connector and measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E72-1 (VC5) - E72-7 (AGND)
    GR-R - L
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    E72-4 (CODE) - E72-7 (AGND)
    P - G
    Demodulated signal of key code data
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    E72-5 (TXCT) - E72-7 (AGND)
    LG - R
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    If the result is not as specified, the amplifier may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139208E01
      Waveform 1
      Tester Connection
      E72-4 (CODE) - E72-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B139205E01
      Waveform 2
      Tester Connection
      E72-5 (TXCT) - E72-7 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder


CHECK TRANSPONDER KEY ECU

  1. Disconnect the E73 ECU connector and measure the resistance and voltage according to the value(s) in the table below.
    B088367E11

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E73-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E73-1 (+B) - E73-16 (GND)
    W-R - W-B
    Battery
    Always
    11 to 14 V
    E73-2 (IG) - E73-16 (GND)
    B-O - W-B
    Ignition switch signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V
    E73-3 (KSW) - E73-16 (GND)
    G-Y - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    10 kΩ or higher
    Key is in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E73 ECU connector and measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E73-5 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    E73-3 (KSW) - E73-16 (GND)
    G-Y - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    11 to 14 V
    Key is in ignition key cylinder
    Below 1 V
    E73-14 (VC5) - E73-5 (AGND)
    GR-R - L
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    E73-4 (TXCT) - E73-5 (AGND)
    LG-R - L
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    E73-15 (CODE) - E73-5 (AGND)
    P-G - L
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    E73-13 (EFIO) - E73-16 (GND)
    W-R - W-B
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 3
    E73-12 (EFII) - E73-16 (GND)
    L-O - W-B
    ECM input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 4
    E73-9 (D) - E73-16 (GND)
    R-Y - W-B
    Diagnostic tester communication
    Without communication
    Below 1 V
    During communication
    Pulse generation
    E73-7 (CTY) - E73-16 (GND)
    R-B - W-B
    Door courtesy signal
    Switch pushed
    11 to 14 V
    Switch free
    Below 1 V
    E73-8 (IND) - E73-16 (GND)
    V-W - W-B
    Security indicator signal
    Security indicator light is on
    11 to 14 V
    Security indicator light is off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139205E01
      Waveform 1
      Tester Connection
      E73-4 (TXCT) - E73-5 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B139208E01
      Waveform 2
      Tester Connection
      E73-15 (CODE) - E73-5 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder

    3. B139206E01
      Waveform 3
      Tester Connection
      E73-13 (EFIO) - E73-16 (GND)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    4. B164432E01
      Waveform 4
      Tester Connection
      E73-12 (EFII) - E73-16 (GND)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON


CHECK ECM

  1. Disconnect the E46 ECM connector and measure the resistance according to the value(s) in the table below.
    A121603E11

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E46-35 (EOM) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E46 ECM connector. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E46-16 (IMI) - E46-35 (EOM)
    W-R - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 1
    E46-15 (IMO) - E46-35 (EOM)
    L-O - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139206E01
      Waveform 1
      Tester Connection
      E46-16 (IMI) - E46-35 (EOM)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    2. B164432E01
      Waveform 2
      Tester Connection
      E46-15 (IMO) - E46-35 (EOM)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Aug 2014)TERMINALS OF ECU (from Aug 2009) →