Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
DTCs for the CAN communication system are as follows: U0073, U0100, U0123, U0124, U0126 and U0129.
Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.
Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
*: Use the intelligent tester.
1.VEHICLE BROUGHT TO WORKSHOP
NEXT
2.INSPECT BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
NEXT
3.CHECK AND CLEAR DTC*
Using the intelligent tester, perform the Health Check (all DTCs check).
NOTICE:
If there is a CAN communication trouble code that indicates that an ECU or sensor has a power malfunction or interior malfunction which is causing a communication stop, the problem may not be in the communication line.
When CAN communication related connectors are disconnected with the ignition switch ON or ACC, the ECU related to the connector and ECUs of related systems will store a CAN communication DTC.
NEXT
4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
Based on the vehicle equipment and specifications, confirm the systems that use CAN communication (Click here).
NEXT
5.CHECK DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE (CANH - CANL)
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
Proceed to
6 (CANH) - 14 (CANL)
Ignition switch off
OK (54 to 69 Ω)
A
6 (CANH) - 14 (CANL)
Ignition switch off
NG (70 Ω or higher)
B (for LHD)
C (for RHD)
6 (CANH) - 14 (CANL)
Ignition switch off
NG (Below 54 Ω)
D (for LHD)
E (for RHD)
Text in Illustration
*a
DLC3
B.
C.
D.
E.
A
6.CHECK V BUS CIRCUIT +B (CANH, CANL - BAT)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (CANH) - 16 (BAT)
Ignition switch off
6 kΩ or higher
14 (CANL) - 16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration
*a
DLC3
Result
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
B.
C.
A
7.CHECK V BUS CIRCUIT GND (CANH, CANL - CG)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
6 (CANH) - 4 (CG)
Ignition switch off
200 Ω or higher
14 (CANL) - 4 (CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
DLC3
Result
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
B.
C.
A
8.CHECK ECUS CONNECTED TO CAN BUS*
Connect the cable to the negative (-) battery terminal.
Select "CAN Bus Check" from "System Select".
Wait 1 minute and then check the display of the connected ECUs and sensors.
Result
Result
Proceed to
All ECUs and sensors connected to the CAN communication system are displayed on the screen.
A
One ECU or sensor connected to the CAN communication system are displayed on the screen.
B
2 or more ECUs and sensors connected to the CAN communication system are displayed on the screen.
C
NOTICE:
The ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.
HINT:
If the display of an ECU is intermittent during the check, one side of an ECU or sensor branch wire is open (The signal of the ECU is treated as noise, which affects the response and display of the intelligent tester).
B.
C.
A
9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*
Select "CAN Bus Check" from "System Select".
Write down all of the DTCs stored in each ECU.
HINT:
If there are communication malfunction DTCs stored but the intelligent tester "CAN Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN system, the communication malfunction DTCs may be past malfunctions that are no longer present.
For V bus main wire malfunctions, related ECUs are also detected. Therefore, determine the malfunctioning area based on all of the DTCs that are output.
NEXT
10.CHECK DTC COMBINATION TABLE (V BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION)
Based on the combination of stored CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction (Click here).
NEXT
11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)*
Using the intelligent tester, clear all DTCs.
Perform a malfunction simulation test on all harnesses and connectors related to the V bus circuit main wire.
Check the DTCs that were stored as a result of the malfunction simulation test. Then determine the malfunctioning area.