2011-2016 FJ Cruiser · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B135155
    Hook the stay of the retractor onto the 2 rear seatback frame hooks and install the retractor with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.


2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

  1. B130768
    Install the rear seatback frame.

  1. B130767E02
    Using hog ring pliers, install 17 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

  1. B135129E02
    Install the belt of the rear center seat outer belt into the rear seatback cover band.
    Text in Illustration 
    *1
    Band


3. INSTALL REAR SEATBACK STOP BUTTON GROMMET

  1. B130771
    Engage the 2 claws and install the rear seatback stop button grommet.


4. INSTALL REAR SEATBACK LOCK RELEASE BUTTON

  1. B130773
    Install rear seatback lock release button.


5. INSTALL REAR SEAT HEADREST SUPPORT

B130770E02
Text in Illustration 
*a
Protrusion

HINT:
Use the same procedure to install all the rear seat headrest supports.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.


6. INSTALL REAR SEATBACK LOCK COVER

  1. B130761
    Engage the claw and install the rear seatback lock cover.

  1. Tighten the screw.


7. INSTALL REAR SEAT SHOULDER BELT COVER

  1. B267855
    Engage the 4 claws and install the rear seat shoulder belt cover.


8. INSTALL SHOULDER BELT ANCHOR COVER

  1. B267854
    Engage the 2gides and 2 claws, install the shoulder belt anchor cover.


9. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

  1. B130760E02
    Push the lock button of the rear seat headrest support and install the rear seat headrest.
    Text in Illustration 
    *1
    Lock Button


10. INSTALL REAR SEAT HEADREST ASSEMBLY

  1. B130759E02
    Push the lock button of the rear seat headrest support and install the rear seat headrest.
    Text in Illustration 
    *1
    Lock Button


11. INSTALL REAR SEATBACK ASSEMBLY

  1. B130750E01
    Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.

  1. B135128E01
    Install the rear seat inner belt into the rear seatback holder.

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.


12. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY

  1. B130749
    Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.

← INSTALLATION (Jul 2007 – Oct 2010)COMPONENTS (from Nov 2010) →