2011-2016 FJ Cruiser · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (w/ Front Seat Side Airbag) (Click here).

HINT:
The procedure described below is for the driver side. Use the same procedure for both the driver and front passenger sides, unless otherwise specified.


1. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B130778E01
    Install the front seat inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

  1. Install the wire harness into the claw of the front seat cushion inner shield.

  1. B130776
    for Driver Side:

    1. Install the 2 clamps and the 2 connectors.

    2. Connect the seat position sensor connector.

  1. B177952
    for Front Passenger Side:

    1. Install the 2 clamps and the connector.

    2. Connect the buckle switch connector.

    3. Connect the occupant classification connector.


2. INSTALL FRONT SEAT ASSEMBLY

B130666E01

NOTICE:
Follow the procedure described below in order to prevent the seat tracks from locking separately.

  1. Insert the 2 locating pins through the 2 body holes, place the front seat in the most rearward position and make sure that the inner and outer seat tracks are locked securely.

  1. Tighten bolt 1 and then bolt 2 onto the front side.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat to the most forward position, and then make sure that the inner and outer seat tracks are locked securely.

  1. Tighten bolt 3 and then bolt 4 onto the rear side.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.

    HINT:
    If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.

  1. B135118
    for Driver Side:

    1. Connect the 2 buckle switch connectors.

    2. w/ Front Seat Side Airbag:

      1. Connect the airbag connector.

    3. Install the clamp.

  1. B177957
    for Front Passenger Side:

    1. Connect the connector.

    2. w/ Front Seat Side Airbag:

      1. Connect the airbag connector.

    3. Install the clamp.


3. INSTALL FRONT SEAT TRACK COVER

B138598E01

HINT:
Use the same procedure for both sides.

  1. Insert the front seat track cover 2 guides in between the seat rail and the seat leg. Then slightly lift up the front seat track cover rear part and carefully push the front seat track cover in until it cannot be pushed in any further.

  1. B138599E01
    Carefully insert the front seat track cover outside claw into the seat leg corner groove according to the procedure shown in the illustration.

  1. Carefully push directly from the top of the front seat track cover inside claw to insert it into the seat leg corner groove, as shown in the illustration.


4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


5. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)
(Click here)
← INSTALLATION (Nov 2010 – Jul 2012)COMPONENTS (Jul 2007 – Oct 2010) →