Home › BODY ELECTRICAL › DOOR LOCK › UNLOCK WARNING SWITCH (for LHD)
REMOVAL
Removal / installation · Vehicles built Nov 2010 – Jul 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.
REMOVE FRONT DOOR SCUFF PLATE RH
Disengage the 14 claws and remove the front door scuff plate.
3.
REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
4.
REMOVE FRONT FLOOR FOOTREST
Disengage the 4 claws and remove the front floor footrest.
5.
REMOVE FOOTREST CLIP
Remove the 2 footrest clips.
6.
REMOVE COWL SIDE TRIM BOARD RH
Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
7.
REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
8.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Separate the front door opening trim weatherstrip LH.
9.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Separate the front door opening trim weatherstrip RH.
10.
REMOVE ASSIST GRIP PLUG (w/ Assist Grip)
HINT:
Use the same procedure to remove all the assist grip plugs.
Text in Illustration
*1
Protective Tape
*a
for RH Side
*b
for LH Side
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
11.
REMOVE ASSIST GRIP ASSEMBLY (w/ Assist Grip)
HINT:
Use the same procedure to remove all the assist grips.
Text in Illustration
*a
for RH Side
*b
for LH Side
Remove the 2 screws and the assist grip.
12.
REMOVE FRONT PILLAR GARNISH RH
w/ Assist Grip:
Disengage the 2 clips and the guide and remove the front pillar garnish.
w/o Assist Grip:
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
Text in Illustration
*1
Protective Tape
Remove the bolt.
Disengage the 2 clips and the guide and remove the front pillar garnish.
13.
REMOVE FRONT PILLAR GARNISH LH
HINT:
Use the same procedure as for the RH side.
14.
REMOVE INSTRUMENT PANEL GARNISH LH
Remove screw <G>.
Disengage the 3 clips and remove the instrument panel garnish.
NOTICE:
Pull the instrument panel garnish up at an angle of 45° to remove it.
Do not damage the surface of the instrument panel when removing it.
15.
REMOVE INSTRUMENT PANEL GARNISH RH
Remove screw <G>.
Disengage the 3 clips and remove the instrument panel garnish.
NOTICE:
Pull the instrument panel garnish up at an angle of 45° to remove it.
Do not damage the surface of the instrument panel when removing it.
16.
REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY
Remove the 2 screws.
Disengage the 4 clips and remove the integration control panel assembly.
Disconnect the 3 connectors.
17.
REMOVE RADIO RECEIVER ASSEMBLY
Remove the 4 bolts.
Disconnect the connectors and remove the radio receiver.
18.
REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY
Disengage the 4 claws.
Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 guides and remove the parking brake hole cover.
19.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
Remove the shift lever knob.
20.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)
Remove the shift lever knob.
21.
REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY
Shift the shift lever into the N position.
Disengage the 5 clips and 3 guides and remove the console upper rear panel.
22.
REMOVE BOX BOTTOM MAT
Remove the box bottom mat.
23.
REMOVE FRONT CONSOLE BOX
Remove the 4 <H> bolts.
Disengage the 5 guides and remove the console box.
24.
REMOVE CONSOLE UPPER PANEL NO. 1 GARNISH
Disengage claw and the clip.
Slide the console upper panel garnish toward the rear of the vehicle, disengage the guide and remove the console upper panel garnish.
25.
REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY
Remove the 2 clips and 2 <E> bolts.
Disengage the 3 clips and 2 claws and remove the instrument lower cover.
26.
REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Disengage the 4 clips and 2 claws and remove the instrument panel register.
NOTICE:
To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
Pull the instrument panel register up diagonally to remove it.
27.
SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the 3 claws and separate the hood lock control lever.
28.
REMOVE INSTRUMENT PANEL FINISH PLATE
Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
Text in Illustration
*1
Protective Tape
*2
Instrument Panel Finish Plate
29.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
Remove the 2 <E> bolts.
Disengage the 5 clips and claw and remove the lower instrument panel finish panel.
30.
REMOVE LOWER INSTRUMENT PANEL LH
Remove the 4 <E> bolts and the lower instrument panel.
31.
REMOVE INSTRUMENT CLUSTER LOWER FINISH PANEL
Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.
Disconnect the connectors.
32.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws.
Disconnect the 2 connectors and clamp and remove the combination meter.
33.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
Text in Illustration
*1
Stopper
Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.
34.
REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH
Remove the screw <A>.
Disengage the 2 clips and claw and remove the instrument panel lower finish panel.
Separate the connectors from the instrument panel lower finish panel.
35.
REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Apply protective tape, as shown in the illustration.
Text in Illustration
*1
Protective Tape
Using a thin-bladed screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel hole cover.
Remove the bolt <E> and clip.
Disengage the 4 clips and 2 claws and remove the instrument panel register.
NOTICE:
To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
Pull the instrument panel register up diagonally to remove it.
36.
REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Disengage the 4 clips and claw and remove the instrument panel speaker panel.
37.
REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
HINT:
Use the same procedure as for the RH side.
38.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
Remove the 2 bolts and the front speaker.
Disconnect the speaker connector.
39.
REMOVE ASSIST GRIP RETAINER RH (w/ Assist Grip)
Remove the 2 bolts and remove the assist grip retainer.
40.
REMOVE ASSIST GRIP RETAINER LH (w/ Assist Grip)
HINT:
Use the same procedure as for the RH side.
41.
DISCONNECT PASSENGER AIRBAG CONNECTOR
Slide the slider and disconnect the passenger airbag connector.
Text in Illustration
*1
Slider
42.
REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
Disengage the clamps and disconnect the connectors.
Remove the 2 <B> bolts, 2 <D> bolts, 7 <C> bolts and nut <F> and remove the instrument panel.
43.
REMOVE INSTRUMENT PANEL FINISH PANEL END LH
Disengage the 3 claws and remove the instrument panel finish panel end.
44.
REMOVE IGNITION SWITCH LOCK CYLINDER AND KEY SET
Turn the ignition switch lock cylinder to the ACC position.
Push down the stop pin with a screwdriver and pull out the ignition switch lock cylinder.
45.
REMOVE KEY INTER LOCK SOLENOID (for Automatic Transmission)
Disconnect the clamp from the steering column bracket upper.
Remove the 2 screws and the key inter lock solenoid.
46.
REMOVE UNLOCK WARNING SWITCH
Disconnect the connector.
Remove the unlock warning switch toward the rear of the vehicle by pushing up the center part.