2011-2016 FJ Cruiser · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Jul 2007


1. INSTALL TRANSFER EXTENSION HOUSING OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. F043486E01
    Using SST and a hammer, tap in the oil seal until its surface is flush with the housing upper surface.
    SST
    09316-60011   (09316-00011)


2. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear)
  1. Using SST and a hammer, tap in a new oil seal (for rear) in the same way as the oil seal (for front).

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.


3. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Apply gear oil to the connecting areas of the companion flange and output shaft.

  1. Using SST, install the companion flange (rear) in the same way as the companion flange (front).

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }


4. INSTALL REAR PROPELLER SHAFT ASSEMBLY

C098700E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }

  1. C098699E02
    Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }


5. INSTALL LOWER TRANSFER CASE PROTECTOR
  1. Install the protector with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }


6. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


7. CHECK FOR TRANSFER OIL LEAKAGE
  1. Remove the case plug (for filler) and gasket.

  1. C083746E01
    Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-3

    Viscosity:
    SAE 75W-90

    Standard capacity:
    1.0 liter (1.1 US qts, 0.9 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← REMOVAL (from Jul 2007)PRECAUTION (from Jul 2007) →